Summary of VITA 7100K
Page 1
Vita k series user’s manual 2007 july v1.1 copyright 2007 july all rights reserved manual version 1.1.
Page 2
The information contained in this document is subject to change without notice. We make no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. We shall not be liable for errors contained her...
Page 3: Ce Mark
Safety important safety instructions 1. To disconnect the machine from the electrial power supply, turn off the power switch and remove the power cord plug from the wall socket. The wall socket must be easily accessible and in close proximity to the machine. 2. Read these instructions carefully. Sav...
Page 4: Caution On Lithium Batteries
Caution on lithium batteries there is a danger of explosion if the battery is replaced incorrectly. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions. Legislation and weee symbol 2002/96/ec waste electri...
Page 5: Table of Contents
Table of contents 1. Item checklist ..............................................................................................5 2. System view .................................................................................................6 2.1. Front view..........................................
Page 6: 1. Item Checklist
1. Item checklist remove the unit from the carton by holding it with the foam inserts: a. Driver cd b. Com port cable c. Power cable d. Power adapter e. System 5.
Page 7: 2. System View
2. System view 2.1. Front view touch screen 2.1. Rear view vesa mount hdd cover i/o ports 6.
Page 8: 2.2. I/o View
2.2. I/o view cash drawer parallel dc in com1,2,3,4 vga usb power switch lan line in line out 7.
Page 9: 3. Specification
3. Specification main name vita 7100k vita 7300k vita 7500k vita 7900k cpu support intel pentium m 1.8ghz chipset intel 855gm fsb 400 mhz system memory 2 x ddr so-dimm slot, up to 2gb graphic memory shared system memory 8 ~ 64mb bios award bios lcd touch panel lcd size 12” tft lcd 15” tft lcd 17” tf...
Page 10
Power adapter dc 19v, 90w audio speaker one 3 w speaker two 3w speakers environment emc & safety fcc, class a, ce, lvd operating temperature o ~ 40℃ (32℉ ~ 104℉) storage temperature -20 ~ 60℃ (-4℉ ~ 140℉) operating humidity 5% ~ 95% rh non condensing storage humidity 5% ~ 95% rh non condensing dust ...
Page 11: 4. Jumper Settings
4. Jumper settings jp2 pwr1 rj45_1 rj11_1 cn2 cn1 rj45_2 usb2 usb1 prn1 sw1 pci1 ide1 dimm1 cpu1 cn19 cn20 cn15 cn21 cn13 cn18 jp11 jp4 jp9 jp10 jp3 jp1 jp5 jp7 jp6 10
Page 12
1. Connectors connector function connector function cn1 audio line out ied1 primary ide connector cn2 audio line in prn1 parallel port cn13 com5 for touch pwr1 +19v power adapter cn15 cpu fan connector rj11_1 cash drawer connector cn16 hardware reset rj45_1 lan (on board) cn18 usb2 rj45_2 com1, com2...
Page 13
3. Cash drawer power setting voltage jp4 +12v ◎1-2 +24v 3-4 +19v 5-6 4. Com3 & com 4 power setting function jp3 com3 pin10_ri ◎1-2 com3 pin10_+5v 3-4 com3 pin10_+12v 5-6 com4 pin10_ri ◎7-8 com4 pin10_+5v 9-10 com4 pin10_+12v 11-12 5. Card reader setting function ◎docking on board jp11 (1-2) n/c 1-2 ...
Page 14
7. Com2 rs232 / 485 / 422 setting function ◎rs232 rs485 rs422 jp9 (1-2) v jp9 (3-4) v jp9 (4-6) v jp9 (5-7) v jp9 (7-8) v jp9 (9-10) v jp10 (1-2) v jp10 (3-4) v jp10 (5-6) v jp10 (7-8) v jp10 (9-10) v jp10 (11-12) v note: open short 3. Connectors pin definition cn4: speaker & mic connector pin 1 amp...
Page 15
Cn13: com5 pin 1 dcd# pin 2 rx# pin 3 tx# pin 4 dtr# pin 5 gnd pin 6 dsr# pin 7 rts# pin 8 cts# pin 9 ri pin 10 +5v cn15: cpu fan connector pin 1 +5v pin 2 feedback pin 3 gnd cn18: usb 2 pin 1 +5v_usb1 pin 2 usb20_r_p1 pin 3 usb20_r_p1+ pin 4 gnd cn19: lvds interface pin 1 lvds_b0+ pin 2 lvds_a3+ pi...
Page 16
Cn20: inverter connector pin 1 +12v_inv pin 2 +12v_inv pin 3 +12v_inv pin 4 +12v_inv pin 5 back-light enable pin 6 n/c pin 7 n/c pin 8 back-light enable pin 9 gnd pin 10 gnd pin 11 gnd pin 12 gnd cn21: pos card reader connector pin 1 +5v pin 2 +5v pin 3 kdata_sio_to_msr pin 4 kdata_sio_to_msr pin 5 ...
Page 17
Pin 19 gnd pin 20 rs232_2_ri rj45_2: com1, com2, com3, com4 pin 21 n/c pin 22 rs232_3_dcd# pin 23 rs232_3_dsr# pin 24 rs232_3_rx# pin 25 rs232_3_rts# pin 26 rs232_3_tx# pin 27 rs232_3_cts# pin 28 rs232_3_dtr# pin 29 gnd pin 30 rs232_3_ri pin 31 n/c pin 32 rs232_4_dcd# pin 33 rs232_4_dsr# pin 34 rs23...
Page 18: 5. Bios Settings
5. Bios settings 1. Bios setup utility the bios setup defines how the system is configured. You must run this program the first time you configure your unit. You may need to run it again if you change the configuration. You must connect a pc keyboard to the keyboard connector to run the bios setup u...
Page 19
Standard cmos features use this menu for basic system configuration. Advanced bios features use this menu to set the advanced features available on the system. Advanced chipset features use this menu to change the values in the chipset registers and optimize the system’s performance. Integrated peri...
Page 20
Set supervisor password enables you to change, set, or disable the supervisor or user password. Set password change, set, or disable the password. It allows you to limit access to the system and to the setup, or just to the setup. Save & exit setup save cmos value changes to cmos and exits setup. Ex...
Page 21: 6. Airflow Requirements
6. Airflow requirements do not block the air vents on the cpu. These vents are necessary for cooling purposes. Do not place the cpu in an enclosed area where sufficient ventilation is not available. Leave at least 150 mm (6 in.) of clearance on the sides where air vents are located. 20