Tansun Quartzheat SOR 210IP Reference Manual - page 4
1. Securely fasten the L-shaped wall brackets to the mounting surface using both
of the fixing holes in the short part of the bracket (see Fig. J for mounting hole
centres). Please refer to Table 1 for recommended positioning of the heater.
Please note. wall fixings are not supplied. They should be selected to
substantially support the weight of the installation. If in doubt contact a
professional for advice!
A s s e m b l i n g - T w o I n d i v i d u a l H e a t e r s J o i n e d
1. Take the first heater and place it face down on a flat surface.
2. Take the second heater and place it face down and positioned parallel to the first heater.
3. Push the M8 bolts (used to hold the wall brackets through the hole in the brackets on the rear heaters
and slide a shake-proof washer on all the threads from the protruding side.
4. Slide the joining bars on each bolt and fit a washer and nut – do not fully tighten at this point.
5. Ensure the second heater is still parallel to the first and sitting flat.
6. Slide the joining bars on each protruding bolt of the other heater to connect them together and fit the
washers and nuts.
7. Again, ensuring the heaters remain flat, fully tighten all four nuts to secure the joining bars in place.
W a l l M o u n t i n g - T w o I n d i v i d u a l H e a t e r s J o i n e d
When two Sorrento IP heaters are joined together they can be mounted in a horizontal or angled
manner as the emitter is a universal burning type.
When wall mounting two Sorrento IP heaters joined together in a horizontal manner, do not position
the heater at an angle more than 45° and less than 10° as shown in Fig. G.
When vertically mounting two Sorrento IP heaters joined together, ensure the mounting surface is
angled so the heater projects downwards - see Fig. C on Page. 3. Do not position the heater at an
angle more than 45° and less than 30° to the horizontal as shown. Position the heater so the cords
are exiting the terminal box pointing down.
Fig. G
Fig. H
Fig. F
Fig. E
DRILLING HOLE TEMPLATE DIMENSIONS FOR
WALL MOUNTED BRACKETS - 1 x HEATER
M o u n t i n g - S i n g l e U n i t w i t h O p t i o n a l S w i v e l B r a c k e t
1. When wall mounting, securely fasten the L-shaped wall bracket to the mounting surface using both
of the fixing holes in the short part of the bracket. Refer to Table 1 for recommended positioning of the
heater. Please note: wall fixings are not supplied. They should be selected to substantially support the
weight of the installation. If in doubt contact a professional for advice!
2. The heater can be fixed to the wall bracket securely with the nuts and bolts provided as shown in
Fig. F.
3. The heater should be mounted with the terminal box at the bottom of the heater.
4. When wall mounting, fix in the required angular position by tightening the fixing bolts on the brackets
at the rear of the heater as pointed out in Fig. F.
5. Secure the supply cable so it is not resting on the body or obstructing the air-vents.
Always isolate the heater from the mains supply when adjusting the position.
Always allow the heater to cool before attempting to reposition/move. Never attempt to move the heater while it is switched on!
Observe the minimum safe distance between the heater body and inflammable surfaces and objects when mounting.
Please refer to Table 1 for the recommended positioning of the heater with regards to minimum distances. Do not install the heater in a corner!
Keep out of the reach of children.
Fig. J
DRILLING HOLE TEMPLATE DIMENSIONS FOR
WALL MOUNTED BRACKETS - 2 × HEATERS
4
When two Sorrento IP heaters are joined they can be hung from a ceiling from chains.
Always allow the heater to cool before attempting to reposition/move. Never attempt to move
the heater while it is switched on!
Observe the minimum safe distance between the heater body and inflammable surfaces and
objects when mounting.
Please refer to Table 1 for the recommended positioning of the heater with regards to
minimum distances. Do not install the heater in a corner!
Keep out of the reach of children.
1. Please refer to Table 1 for recommended positioning of the heater. When hanging from a
ceiling two chains of equal length and gauge are required and should be selected with fixings
that are more than adequate to hold the weight of the heater. If in doubt contact a
professional for advice!
2. Fix the heater assembly to the chains via the hole in the centre of the joining bar as shown in
Fig. K. and ensure the heater faces directly down when hanging.
3. Secure the supply cable so it is not resting on the body or obstructing the air-vents.
Always isolate the heater from the mains supply when adjusting the position.
Fig. K
A s s e m b l i n g - T h r e e I n d i v i d u a l H e a t e r s J o i n e d
1. Take the first heater and lie it face down on a flat surface.
2. Take the second and third heaters and position them face down and parallel to the first.
3. Push the M8 bolts (used to hold the wall brackets through the hole in the brackets on the rear heaters and slide a shake-proof washer on all the
threads from the protruding side.
4. Slide the long joining bar (not supplied, available separately) on each bolt and fit a washer and nut – do not fully tighten at this point.
5. Position the second heater so it’s parallel to the first and sitting flat.
6. Take the third heater and a long joining bar. Push a bolt and washer through the end hole and place a serrated washer on the other side. Push the
bolt through the bracket hole on heater. Repeat on opposite side and secure with a washer and nut – do not fully tighten at this point.
7. Position the third heater so it’s parallel to the second.
8. Line-up the bars of the first heater with the brackets of the second heater – they should go on the inside faces like heater one.
9. Line-up the bars of the third heater with the brackets of the second heater – these should go on the outside faces like heater three.
10. Push a bolt from the back of the long joining bars through the holes putting a serrated washer on each side of the heater bracket.
11. Fit a washer and nut to both sides and providing the assembly is sitting flat, fully tighten both sides and also the nuts of the first and third heaters to
the long joining bars.
12. The heater is now ready for mounting or hanging.
C e i l i n g H a n g i n g - T w o I n d i v i d u a l H e a t e r s J o i n e d
2. Fix the heater assembly to the brackets via the hole in the centre of the joining bar. The joining bars should slide inside the gap of the two wall
brackets.
3. Place a bolt and washer in the hole of the wall bracket and put a serrated washer on the opposite side between the bracket and joining bar. Repeat
on opposite side.
4. Fit the heater assembly to the brackets and place a washer and nut on the bolts protruding through the joining bars.
5. Fully tighten the nut and bolts with the heater set at the desired angle (Fig. H).
6. Secure the supply cable so it is not resting on the body or obstructing the air-vents.
Always isolate the heater from the mains supply when adjusting the angular position.
5