Gate by sq•2 power on threshold close ratio threshold attack release auto in/out output level chan 1 in/out channel 1 channel 2 threshold close ratio threshold attack release auto in/out output level chan 2 in/out compressor / limiter compressor / limiter off + 10 0 dbu -70 -50 -30 -15 -40 + 20 + 10...
2 safety instructions 1. Read instructions — all the safety and operation instructions should be read before this product is operated. 2. Retain instructions — the safety and operating instructions should be kept for future reference. 3. Heed warnings — all warnings on this product and in these oper...
Part no. 0009426 rev. A 1/04 ©2004 loud technologies inc. All rights reserved. 3 what me, read a manual? Before you begin, please make sure you read the safety instructions on page 2 and getting started on page 4. Your new tapco ® sq•2 is designed to set up quickly and operate easily. We know it’s o...
4 getting started the following steps will help you set up your sq•2, and get the levels just right. Settings: 1. Be sure the sq•2’s power switch is off. 2. Turn all the controls to their center positions (12 o’clock) and set all the switches out. Connections: 1. Using balanced or unbalanced cables,...
5 don’t forget to visit our website at www.Tapcogear.Com for more information about this and other tapco products. Contents safety instructions................................................................2 getting started ....................................................................4 intro...
6 introduction thank you for choosing a tapco ® squeez™ dynamics processor by mackie ® . The tapco product line hails back to the days of tapco corporation, greg mackie’s fi rst company. Tapco revolutionized the audio industry back in 1969 with the very fi rst 6-channel mixer specifi cally designed ...
7 the gate/expander typically, a gate is used to turn off a channel when there is no signal to reduce the overall noise level of the mix. When the signal drops below a certain level determined by the threshold control, it is turned off. When the signal comes back up and crosses the threshold, the le...
8 ac fuse t 0.315a serial / date code tip = input ring = output sleeve = ground bal/ unbal input side chain output bal/ unbal tip = input ring = output sleeve = ground output bal/ unbal bal/ unbal input side chain brought to you by the groovy folks in woodinville, wa, usa manufactured in china • "ta...
9 sq•2 features 5. Attack this control determines how fast the compressor reacts once the threshold has been exceeded. It ranges from 0.1 ms (milliseconds) to 200 ms. If you want to use the compressor as a limiter, set the attack knob to its lowest setting (0.1 ms). This way the limiter quickly catc...
10 air filter 10. Level the air fi lter is a unique feature that restores brilliance and sizzle to compressed signals. It provides a high-frequency boost to the signal after the compression stage. It ranges from off to full, where full provides the maximum high-frequency boost. Certain instruments s...
11 15. Output two types of connectors are provided for the outputs — male xlr and 1/4” trs (tip-ring-sleeve). These balanced outputs are in parallel, and provide exactly the same signal. You can connect either a balanced trs connector or an unbalanced ts connector to the 1/4” output jack. See “appen...
12 appendix a: service information no sound • is the gate threshold control turned up too high? Turn the gate threshold all the way off and see if you hear anything. • is the signal source turned up? Make sure the signal level from the mixing console (or whatever device immediately precedes the sq•2...
13 6. Write the ra number in big print on top of the box. Units sent to us without the ra number will be refused. 7. Ship the sq•2 to us. We suggest insurance for all forms of cartage. Ship to this address: tapco service department 16220 wood-red road ne woodinville, wa 98072 8. We’ll try to fi x th...
14 appendix b: connections 1/4" ts phone plugs and jacks “ts” stands for tip-sleeve, the two connection points available on a mono 1/4" phone jack or plug. They are used for unbalanced signals. Sleeve tip tip sleeve tip sleeve 1/4" ts unbalanced wiring: sleeve = shield tip = hot (+) 1/4" trs insert ...
15 appendix c: technical info sq•2 specifi cations frequency response 20 hz to 20 khz (+0, –1 db) audio input type: active balanced xlr and 1/4" jacks impedance: 60 k Ω balanced maximum input level: +21 dbu balanced and unbalanced audio output type: xlr and 1/4" jacks impedance: k Ω unbalanced maxim...
16 sq•2 block diagram this outlines the signal fl ow inside the sq•2. Balanced line input (trs) balanced line input (xlr-f) side chain inser t (trs) 1 2 3 ga te threshold output threshold a t t a c k release ra tio air fil ter level out in au t o at ta c k / release chan 1 in/out vca (v ol ta ge con...
17 byb y sq • 2 power on threshold close ratio threshold a ttack release auto in/out output level chan 1 in/out channel 1 channel 2 threshold close ratio threshold a ttack release auto in/out output level chan 2 in/out gate compressor / limiter compressor / limiter off + 10 0 dbu -70 -50 -30 -15 -40...
By 18.
19 tapco limited warranty a. Loud technologies inc. Warrants all materials, workmanship and proper operation of this tapco product for a period of one year from the original date of purchase. If any defects are found in the materials or workmanship, or if the product fails to function properly durin...
Tapcogear.Com.
