Tarantula RS.1 Installation Manual

Manual is about: REMOTE VEHICLE STARTER

Summary of RS.1

  • Page 1

    Fcc id notice this device complies with part 15 of the fcc rules. Operation is subject to the following conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Caution: changes...

  • Page 2: System Programming - Menu 1

    System programming - menu 1 page 2 install manual table of contents wiring diagram.......................................................................Page 3-4 connector pin configuration antenna connection door lock connector bypass connector data port connector tach learning........................

  • Page 3: System Programming - Menu 1

    System programming - menu 1 page 2 install manual table of contents wiring diagram.......................................................................Page 3-4 connector pin configuration antenna connection door lock connector bypass connector data port connector tach learning........................

  • Page 4: System Programming - Menu 1

    System programming - menu 1 page 4 install manual wire diagram 1 2 3 1 2 3 1 2 3 4 position 1 or position 2 green blue n/a* n/a black orange selectable park light output output to activate door lock circuit (-) output to activate door unlock circuit (-) output for voltage inverter* n/a ground for by...

  • Page 5: System Programming - Menu 1

    System programming - menu 1 page 4 install manual wire diagram 1 2 3 1 2 3 1 2 3 4 position 1 or position 2 green blue n/a* n/a black orange selectable park light output output to activate door lock circuit (-) output to activate door unlock circuit (-) output for voltage inverter* n/a ground for by...

  • Page 6: System Programming - Menu 1

    Pin 1 green/ white pin 2 green/ black pin 3 orange/ black pin 4 pin 7 red/ white gray pin 5 pin 8 brown/ white violet/ white pin 6 pin 9 brown gray re-arm (-) programmable supplies one .75 second pulse when locked and one .75 second pulse after remote start shutdown. Factory alarm re-arm/ rap shutdo...

  • Page 7: System Programming - Menu 1

    Pin 1 green/ white pin 2 green/ black pin 3 orange/ black pin 4 pin 7 red/ white gray pin 5 pin 8 brown/ white violet/ white pin 6 pin 9 brown gray re-arm (-) programmable supplies one .75 second pulse when locked and one .75 second pulse after remote start shutdown. Factory alarm re-arm/ rap shutdo...

  • Page 8: System Programming - Menu 1

    System programming - menu 1 page 8 install manual transmitter programming system programming - menu 1 page 9 install manual programming rs.1 rs.1 programming additional transmitters turn ignition key off to exit remote program mode when all required remote’s have been programmed. 1 honk confirms pro...

  • Page 9: System Programming - Menu 1

    System programming - menu 1 page 8 install manual transmitter programming system programming - menu 1 page 9 install manual programming rs.1 rs.1 programming additional transmitters turn ignition key off to exit remote program mode when all required remote’s have been programmed. 1 honk confirms pro...

  • Page 10: Program Menu 1 & 2

    5 bypass module idata™ link bypass fortin™ bypass 8 special disarm pulses acc & gwr when unlocked normal disarm 9 unlock button 1 / 2 button remote only unlock and start for timer mode & menu 4 unlock / lock toggle unlock and start for timer mode & menu 4 unlock output 2nd ignition setting # led fla...

  • Page 11: Program Menu 1 & 2

    5 bypass module idata™ link bypass fortin™ bypass 8 special disarm pulses acc & gwr when unlocked normal disarm 9 unlock button 1 / 2 button remote only unlock and start for timer mode & menu 4 unlock / lock toggle unlock and start for timer mode & menu 4 unlock output 2nd ignition setting # led fla...

  • Page 12: System Programming - Menu 1

    System programming - menu 1 page 12 install manual diagnostics diagnostics chart 2 button remote installer notes to enter diagnostic memory if the remote starter does not activate when the start button is pressed the park lights will flash a diagnostic to indicate what shutdown input has been trigge...

  • Page 13: System Programming - Menu 1

    System programming - menu 1 page 12 install manual diagnostics diagnostics chart 2 button remote installer notes to enter diagnostic memory if the remote starter does not activate when the start button is pressed the park lights will flash a diagnostic to indicate what shutdown input has been trigge...

  • Page 14: System Programming - Menu 1

    Door lock diagrams green vehicle's lock/unlock switch to control relay or actuators negative door lock (low current) alarm and / or starter module door lock output system programming - menu 1 page 14 install manual relay diagrams vehicle's lock/ unlock switch use spdt 12v relay blue negative door lo...

  • Page 15: System Programming - Menu 1

    Door lock diagrams green vehicle's lock/unlock switch to control relay or actuators negative door lock (low current) alarm and / or starter module door lock output system programming - menu 1 page 14 install manual relay diagrams vehicle's lock/ unlock switch use spdt 12v relay blue negative door lo...

  • Page 16

    Website: www.Security.Soundstream.Com tech support: tech-support@soundstream.Com.