Targus DEFCON 3 User Manual

Manual is about: Targus User's Guide Portable Security System

Summary of DEFCON 3

  • Page 1

    Portable security system user’s guide.

  • Page 2

    Introduction congratulations on your purchase of the targus defcon 3 security system - you have selected the most advanced personal property protection available. Now your briefcase, computer, and other personal property are as safe on the road as they are in your home or office! This user’s guide p...

  • Page 3

    Features electronic motion sensor triggers the alarm when motion is detected. You can choose from two different sensitivity settings. Level 1 - low motion sensitivity (default) level 2 - high motion sensitivity alarm volume 84db - low volume 94db - high volume (default) alarm siren choice of six dif...

  • Page 4

    3.

  • Page 5

    4.

  • Page 6

    5 installing batteries figure 3. Installing batteries in the alarm unit 1. Unscrew the end of the cable to detach it. 2. Remove the screw and battery cover from the back of the alarm unit. 3. Insert the batteries in place as shown in figure 3. 4. Replace the battery cover and screw. 5. Reattach the ...

  • Page 7

    6 programming a new remote control when you need to program a new remote control for the alarm unit: 1. Remove the batteries from the alarm unit for at least 10 minutes. 2. Replace the batteries. 3. Press and hold either button on the remote control until the alarm unit beeps six times and the led l...

  • Page 8

    7 programming defcon 3 features the defcon 3 has a program mode that enables you to tailor the alarm unit to your personal preferences through several advanced features. Accessing program mode 1. Make sure the alarm unit is not armed. 2. Press and hold the program button on the remote control for th...

  • Page 9

    8 setting motion sensitivity the defcon 3 alarm unit has two sensitivity settings: low motion sensitivity (level 1): first then . This setting triggers the alarm siren when the unit has detected continuous motion for six seconds. This is the factory default. High motion sensitivity (level 2): first ...

  • Page 10

    9 setting alarm volume your defcon 3 alarm unit has two volume settings: high volume - 94 db (default setting) low volume - 84 db 1. Access program mode. Alarm volume is the second feature you encounter in program mode. 2. To bypass the motion sensitivity feature and program the alarm volume, press ...

  • Page 11

    10 exiting program mode you may exit program mode at any time. To exit and save your selections, press and hold the program button for three seconds. A special tone sounds with four rapid flashes from the left led light . If no signal is received from the remote control for 20 seconds, the alarm uni...

  • Page 12

    11 specifications power: current consumption (armed/disarmed): 0.16 - 1.6 ma current consumption (tripped): 60 ma batteries: alarm: three (3) aaa alkaline 1.5 volt remote control: one (1) ansi/neda 1811a or equivalent battery life: alarm: up to 90 days with cable secured or 3 years with cable unsecu...

  • Page 13

    Troubleshooting should you encounter any difficulties in operating your defcon 3 security system, review the following list of common problems and solutions. If the problem remains unresolved, please contact our technical support team. Problem solution system does not operate ensure batteries are pr...

  • Page 14

    13 technical support in the unlikely event that you encounter problems with your targus defcon 3 security system, please use our web site to contact our support group through email. Web site: www.Targus.Com email: techsupport@targus.Com or, call technical support. Our knowledgeable staff is availabl...

  • Page 15

    The leading global supplier of portable solutions visit our web site at www.Targus.Com new york • los angeles • toronto • tokyo • hong kong singapore • sydney • london • paris • brussels • hannover features and specifications are subject to change without notice. ©2000 targus corp. 400-0005-001a.