Tascam AVIOM PRO16 DM-4800 Owner's Manual
IF-AV/DM
Aviom Pro16 A-Net Interface Card
D01106120A
Introduction
Thank you for purchasing the TASCAM IF-AV/DM
Aviom Pro16 A-Net Interface Card. This card allows your
TASCAM Digital Mixer to feed monitor audio to any
number of Aviom Pro16 A-Net devices such as the A-16II
Personal Mixer.
Before using the unit, please take time to read this manual
thoroughly to ensure you understand how to properly set up
and connect the unit, as well as the operation of its many
useful and convenient functions. After you have finished
reading this manual, please keep it in a safe place for future
reference.
You can also download the Owner’s Manual from the
TASCAM web site (http://www.tascam.com).
Features
Transmission of up to 16 channels of audio.
•
Compatible with 24 bit quantization and 44.1 kHz and 48
•
kHz sampling frequency
Convenient on-screen stereo link control.
•
Trademarks
TASCAM is a trademark of TEAC Corporation,
•
registered in the U.S. and other countries.
Aviom, A-Net, and Pro16 are trademarks of Aviom, Inc.
•
Other company names, product names and logos in this
•
document are the trademarks or registered trademarks of
their respective owners.
Product components
The included items are listed below.
Take care when opening the package not to damage the
items. Keep the package materials for transportation in the
future.
Please contact the store where you purchased this unit if any
of these items are missing or have been damaged during
transportation.
Main unit
•
.........................................................................1
Attachment screws
•
..........................................................5
Owner’s Manual (this document)
•
....................................1
Names and functions of parts
1
RJ-45 Connector for A-Net
DM-3200/DM-4800 requirements
In order to use the IF-AV/DM card, the DM-4800/DM-3200
must use software version 1.70 or later. The mixer cannot
recognize the IF-AV/DM card when using earlier versions.
Check the TASCAM website (http://www.tascam.com/) for
the latest DM-4800/DM-3200 software and download the
TFI update file.
Install TMCompanion, which is included on the CD-ROM
included with the DM-4800/DM-3200, on the computer
that you are using. Launch TMCompanion and use the TFI
update file to upgrade the software version used by the
DM-4800/DM-3200.
Installation
NOTE
DM-3200: Install the IF-AV/DM in mixer slot 1. It will not
•
function in slot 2.
DM-4800: Install the IF-AV/DM in mixer slot 1 or 3. It will
•
not function in slot 2 or 4.
Turn the mixer power OFF before beginning installation.
•
1 Remove the five screws from the cover panel of the
slot where you want to install the IF-AV/DM card
(slot 1 on a DM-3200, slot 1 or 3 on a DM-4800), and
then remove the panel. (If that slot already contains
a card, remove the card.)
2 Insert the IF-AV/DM card into the slot. Insert the
card completely, aligning its edges with the white
guidelines on the inside of the slot. Push the card
in until it clicks into place and its backplate is even
with the back of the mixer. Do not, however, push the
card too hard. If you are having difficulty inserting it
properly, pull it out once and try again.
3 Use the five screws that you removed earlier or the
five screws included with this card to fix the card in
place.
4 Turn the mixer’s power ON, and open the DIGITAL
screen (with the ALT key indicator lit, press screen
mode selection key 2). Select the SLOT tab (SLOT
1-2 or SLOT 3-4 for the DM-4800), and confirm that
the unit recognizes the installed card. If a “No Card”
message appears, the card might not have been
inserted properly or the screws might not be tight
enough.
Compatibility
The IF-AV/DM interface card, when installed and properly
configured, is compatible with the following Aviom Pro16
Series products:
A-16II Personal Mixer (the original A-16 is not
•
supported)
A-16R rack-mounted Personal Mixer
•
AN-16/o Output Module
•