1. DL manuals
  2. Task Force
  3. Lawn Mower
  4. 26053
  5. Operator's Manual

Task Force 26053 Operator's Manual

Manual is about: 20 in. REEL MOWER

Summary of 26053

  • Page 1

    Tm 20 in. Reel mower item / articulo # 227683 model / modelo #26053 read your operator’s manual completely and carefully before attempting to set up or operate your new reel mower, all operators of this equipment should read and understand all safety rules printed on the machine and in this operator...

  • Page 2

    Table of contents ………………………………………………………………………………….…………..………….………3 ………………………………………………………………………….…………..…………….……2 product specifications product specifications safety information ………………………………………………………………………….…………..………….………3 care and maintenance assembly instructions …………………………………………………………………………….………..…...

  • Page 3

    3 never place hands, fingers or feet inside the reel. Although a motor does not power this mower, when the wheels turn the reel spins and can cut. Never mow when grass is wet as it can be slippery. Do not use the reel mower while barefoot or while wearing sandals. Walk behind, never run, while using...

  • Page 4

    4 assembly instructions 1. Top handle 2. Center handle pieces 3. Left lower handle 4. Right lower handle 5. Foam grip 6. 1- 3/8 in. Bolts 7. Flat washer 8. Wing nut tools required pliers (not included) fig. 1 assembling the handle: (fig.1) note: do not completely tighten bolts until assembly is comp...

  • Page 5: Fig. 2

    Attaching the handle to the mower base:(fig:2) 5 fig. 2 1 2 5 1. Align holes (1) at the lower end of each handle arm with short posts (2) extending from the mower base side plates. Slide lower ends of handle arms onto posts. 2. After handle arm holes are on posts, use pliers to snap c-clips (1) onto...

  • Page 6

    Assembling and attaching the rear bag: (fig. 3, 4, 5 and 6) 1. Layout all components in the packaging. 2. Open all hook and loop seams on the grass bag and place the frame into position and fold hook and loop seams back together. (fig. 3) assembly instructions 6 fig. 3 fig. 4 fig. 6 3. Remove pre-in...

  • Page 7

    Cutting height adjustments: (fig. 7) the cutting height of the mower adjusts from 1-3/4 - 2-3/4 in. By moving the height adjustment levers to the required position. To achieve the lowest cutting position, one at a time, move the the adjustment levers on both sides, located next to the smaller wheels...

  • Page 8

    Mower blade adjustments: (fig. 8 and 9) warning: blades are extremely sharp. To avoid injury, do not touch blades when making note: blades are factory adjusted. Misalignment can occur, often caused by blades being too loose or too tight. This can cause an uneven cut each end of the cutting bar is ad...

  • Page 9

    Two-year limited warranty the manufacturer warranties that this product is free from defects in material and workmanship for two (2) years from the date of the original purchase by the original purchaser only. This warranty is not transferable and does not cover: products sold damaged or incomplete,...

  • Page 10

    Parts diagram 10

  • Page 11

    Item description qty 1 left housing support 1 2 right housing support 1 3 reel cut 1 4 top push handle 1 5 center handle pieces 2 6 lower handle 2 7 pin 2 8 bearing 2 9 gear wheel 2 10 housing 1 11 long shaft 1 12 cutting bar 1 13 cutting bar adjustment bolt 2 14 cutting bar adjustment spring 2 15 s...