Tau K100M Installation Manual
INSTALLATION GUIDE
K100M
Control panel for T-ONE5E gearmotor
D_MNL0K100M 05-06-2012 - Rev.02
WARNING!
Attention: This product may only be installed from professional installers. Only qualiied and trained electricians may connect, programme and
service the controls.
No information given in this manual can be considered as being of interest to end users.
This manual is enclosed with control unit K100M and may therefore not be used for different products!
Important information:
Disconnect electric power to the system before making maintenance, repairs or removing covers
The K100M control unit has been designed to control a electromechanical sliding door operator.
Any other use is considered improper and is consequently forbidden by current laws.
Read all instructions carefully and completely before attempting to install and use this automatic gate operator!
INSTALLATION
Make sure the gate has been properly installed and slides freely in both directions. Repair or replace all worn or damaged gate hardware prior
to installation. A freely moving gate will require less force to operate and will enhance the performance of the operator and safety devices used
with the system.
Also check that the gate operator assembly has been installed according to the instructions.
WARNING: The automatic gate operator must be grounded - All Federal, State and local safety codes must be observed.
ATTENTION:
- do not use solid wire, use only multi threaded wire
- do not reuse pre-existing electric wire.
IF THE ABOVE INSTRUCTIONS ARE NOT FOLLOWED THE “MANUFACTURER” SHALL IN NO EVENT BE LIABLE FOR DIRECT, INDIRECT, INCI-
DENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OR LOSS OF PROFITS WHETHER BASED IN CONTRACT TORT OR ANY OTHER LEGAL
THEORY DURING THE COURSE OF THE WARRANTY OR AT ANY TIME THEREAFTER.
CONTROL PANEL FOR ONE 230 V AC MOTOR
MICROPROCESSOR-CONTROLLED LOGIC
STATUS LEDS
LINE FUSE
BUILT-IN FLASHING LIGHT CIRCUIT
BUILT-IN 433.92 MHz RADIO RECEIVER
MAX. OPERATING TIME 240”
AUTOMATIC 50 / 60 HZ FREQUENCY DETECTION
ADJUSTABLE SOFT-STOP
AMPEROMETRIC OBSTACLE DETECTION
TESTING
Once the connection has been completed:
All the green LEDs must be ON (each of them corresponds to a Normally Closed input). They will turn OFF when the controls to which they are as-
sociated are operated.
The red opening command LEDs must be OFF (each corresponding to a Normally Open input). They will turn ON when the commands they are as-
sociated with are given; red LED DL1 must be ON steadily.
TECHNICAL CHARACTERISTICS
Power input – control board
230 V AC - 50-60 Hz
Nominal power
400 W
230 V AC Input protection fast blow fuse (F1 - 5x20)
F 3,15 A
Power input – motors
230 V AC
Power input – auxiliary circuits
24 V AC
24 V AC Input (auxiliary circuits) fast blow fuse (F2 - 5x20)
F 500 mA
Working temperature
-20°C ÷ +55°C
Protection degree
IP 44
DIAGNOSTICS LED
DL1 (RADIO CONTROLS) / RED
ERROR message / PROGRAMMING of transmitters
DL2 (OPEN/CLOSE) / RED
OPEN / CLOSE pushbutton activated
DL3 (PHOTO) / GREEN
PHOTOCELL activated
DL4 (CLOSE LIMIT SWITCH) / GREEN
CLOSING LIMIT SWITCH activated
DL5 (OPEN LIMIT SWITCH) / GREEN
OPENING LIMIT SWITCH activated
DL6 (STOP) / GREEN
STOP pushbutton activated
English
F
R
SEN
S
T
C
A
F
2
F
1
7
8
9
1
0
1
1
1
2
1
3
1
4
1
2
3
N
e
u
tra
l
23
0 V
AC
Pow
er
sup
ply
Ph
a
se
M-OP
CL
S
OL
S
CO
M
FS1
FS2
M-CO
M
M-CL
4
1
C
H
O
P/
C
L
D
L
3
D
L
4
D
L
5
D
L
6
D
L
2
D
L
1
1
2
3
4
1
2
3
4
F
la
sh
in
g
lig
h
t
2
3
0
V
AC
ma
x.
5
0
W
O
p
e
n
/C
lo
se
St
o
p
An
te
n
n
a
K
1
0
0
M
D
ip
-sw
it
ch
e
s
O
N
M2
M3
D
L
3
D
L
4
D
L
5
D
L
6
D
L
2
D
L
1
PH
O
T
O
C
L
O
SE
L
IMI
T
SW
IT
C
H
O
PEN
L
IMI
T
SW
IT
C
H
ST
O
P
O
PEN
/C
L
O
SE
R
AD
IO
C
O
N
T
R
O
L
S
T
C
A
+
-
SEN
S
+
-
F
R
+
-
Ph
o
to
ce
lls
C
o
mmo
n
Ph
o
to
ce
ll
R
X
1
2
3
4
5
T
X
1
2
0
V
AC
Ph
o
to
ce
ll
-
2
4
V
AC
GB - Translation of original instructions