1. DL manuals
  2. Taylor
  3. Paint Sprayer
  4. 358
  5. Operator's Manual

Taylor 358 Operator's Manual

Manual is about: Thick Shake Dessert Machines

Summary of 358

  • Page 1

    Operator's manual model 358 & 359 thick shake freezers original operating instructions 056788-m 8/2/10 (original publication) (updated 8/25/14).

  • Page 2

    Complete this page for quick reference when service is required: taylor distributor: address: phone: service: parts: date of installation: information found on the data label: model number: serial number: electrical specs: voltage cycle phase maximum fuse size: a minimum wire ampacity: a e 2010 carr...

  • Page 3: Table Of Contents

    Table of contents models 358 & 359 table of contents section 1 to the installer 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installer safety 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 4

    Models 358 & 359 table of contents table of contents - page 2 disassembly 19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Brush cleaning 19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 5: Section 1

    1 models 358 & 359 to the installer 131125 section 1 to the installer the following information has been included in the manual as safety and regulatory guidelines. For complete installation instructions, please see the installation checklist. Installer safety in all areas of the world, equipment sh...

  • Page 6

    2 models 358 & 359 to the installer 131125 air cooled units do not obstruct air intake and discharge openings: air cooled units require a minimum of 3” (76 mm) of clearance around all sides of the freezers and 3-1/2” (89 mm) on the bottom. Model 359 only: installation of air deflector is required. F...

  • Page 7

    3 models 358 & 359 to the installer 131125 refrigerant in consideration of our environment, taylor uses only earth friendly hfc refrigerants. The hfc refrigerant used in this unit is r404a. This refrigerant is generally considered non-toxic and non-flammable, with an ozone depleting potential (odp) ...

  • Page 8: Section 2

    4 models 358 & 359 to the operator 131125 section 2 to the operator your freezers have been carefully engineered and manufactured to give you dependable operation. These units, when properly operated and cared for, will produce a consistent quality product. Like all mechanical products, they will re...

  • Page 9: Section 3

    5 models 358 & 359 safety 131125 section 3 safety we, at taylor company, are concerned about the safety of the operator when he or she comes in contact with the freezer and its parts. Taylor has gone to extreme efforts to design and manufacture built-in safety features to protect both you and the se...

  • Page 10

    6 models 358 & 359 safety 131125 do not use a water jet to clean or rinse the freezer. Failure to follow these instructions may result in serious electrical shock. S do not allow untrained personnel to operate this machine. S do not operate the freezer unless all service panels and access doors are ...

  • Page 11: Section 4

    7 models 358 & 359 operator parts identification section 4 operator parts identification model 358 figure 1 item description part no. 1 cover a.-hopper insul x51658 2 tube-feed-nonrevers 015176-5 3 panel-rear 046021 4 panel-side *358* right 046023-sp1 5 filter a.-13 x 16-7/8 x 7/16 046044 6 stud-nos...

  • Page 12

    8 models 358 & 359 operator parts identification model 359 figure 2 item description part no. 1 panel-side-left 065250 2 cover assembly-hopper x51658 3 tube-feed-nonreversible 015176-5 4 panel-rear 065271 5 filter-air 18 l x 13.5 h x .70 052779-3 6 caster-3” swivel 3/4-10stm 021279 7 panel-side-righ...

  • Page 13

    9 models 358 & 359 operator parts identification beater and door assembly figure 3 item description part no. 1 seal-drive shaft 032560 2 shaft-beater 033235 3 beater a.-7 qt. - 1 pin x46233 4 bearing-front 013116 5 gasket-door - 5.177 id x 5.9380 016672 item description part no. 6 valve a.-draw x460...

  • Page 14

    10 models 358 & 359 operator parts identification accessories figure 4 item description part no. 1 kit assembly-tune up *358 x46050 kit assembly-tune up *359 x36356 2 brush-rear bearing 013071 3 brush-double ended 013072 item description part no. 4 brush-draw valve 014753 5 brush-hopper 3” x 7” 0233...

  • Page 15: Section 5

    11 models 358 & 359 important: to the operator section 5 important: to the operator model 358 model 359 figure 5 figure 6 item description 1 power switch 2 mix out indicator 3 reset button item description 1 mix out indicator-left side 2 power switch-left side 3 mix out indicator-right side 4 power ...

  • Page 16

    12 models 358 & 359 important: to the operator power switch the middle position is “off”. The left position is “wash”, which activates the beater motor only. The right position is “auto”, which activates the beater motor and the refrigeration system. Figure 7 indicator light - “mix out” the “mix out...

  • Page 17: Section 6

    13 models 358 & 359 operating procedures section 6 operating procedures the model 358 has been selected to show you the pictured step-by-step operating procedures for both models contained in this manual. These models, for practical purposes of operation, are the same. These models store 20 quarts (...

  • Page 18

    14 models 358 & 359 operating procedures step 3 check the scraper blades for any nicks or signs of wear. If any nicks are present, replace both blades. If the blades are in good condition, install the scraper blade clips on the scraper blades. Place the rear scraper blade over the rear holding pin o...

  • Page 19

    15 models 358 & 359 operating procedures step 8 place the freezer door gasket into the groove on the back of the freezer door. Slide the white plastic front bearing over the baffle rod onto the bearing hub, making certain the flanged end of the bearing is resting against the freezer door. Do not lub...

  • Page 20

    16 models 358 & 359 operating procedures sanitizing step 1 prepare an approved 100 ppm sanitizing solution (examples: 2-1/2 gal. [9.5 liters] of kay-5r or 2 gal. [7.6 liters] of stera-sheenr). Use warm wa- ter and follow the manufacturer's specifications. Step 2 pour the sanitizing solution into the...

  • Page 21

    17 models 358 & 359 operating procedures step 6 stand the air tube in the corner of the mix hopper. Figure 25 repeat steps 1 through 6 for the other side of the freezer on the model 359. Priming step 1 with a pail beneath the door spout, raise the draw handle. Pour two gallons (7.6 liters) of fresh ...

  • Page 22

    18 models 358 & 359 operating procedures 140804 step 5 place the mix hopper cover in position over the mix hopper. Figure 29 repeat steps 1 through 5 for the other side of the freezer on the model 359. Closing procedure to disassemble your unit, the following items will be needed: s two cleaning pai...

  • Page 23

    19 models 358 & 359 operating procedures cleaning step 1 prepare an approved 100 ppm cleaning solution (examples: 2-1/2 gal. [9.5 liters] of kay-5r or 2 gal. [7.6 liters] of stera-sheenr). Use warm water and follow the manufacturer's specifications. Step 2 pour the cleaning solution into the mix hop...

  • Page 24

    20 models 358 & 359 operating procedures step 5 return to the freezer with a small amount of cleaning solution. With the black bristle brush, brush clean the rear shell bearing(s) at the back of the freezing cylinder(s). Figure 32 step 6 remove the drive shaft drip pan(s) from the front panel and ta...

  • Page 25: Section 7

    21 models 358 & 359 important: operator checklist section 7 important: operator checklist during cleaning and sanitizing always follow local health codes. Cleaning and sanitizing schedules are governed by federal, state, or local regulatory agencies, and must be followed accordingly. If the unit has...

  • Page 26

    22 models 358 & 359 important: operator checklist j 4. Dispose of o-rings and seals if they are worn, torn, or fit too loosely, and replace with new ones. J 5. Follow all lubricating procedures as outlined in “assembly”. J 6. If your machine is air cooled, check the condenser for accumulation of dir...

  • Page 27: Section 8

    23 models 358 & 359 troubleshooting guide section 8 troubleshooting guide problem probable cause remedy page ref. 1. No product is being dispensed with draw valve open and machine in the “auto” mode. A. Beater motor is out on reset. A. Reset the freezer. 12 b. Circuit breaker off or blown fuse. B. T...

  • Page 28

    24 models 358 & 359 troubleshooting guide problem probable cause remedy page ref. 6. The drive shaft is stuck in the drive coupling. A. Mix and lubricant collected in the drive coupling. A. Brush clean the rear shell bearing area regularly. 20 b. Rounded corners of drive shaft, coupling or both. B. ...

  • Page 29

    25 models 358 & 359 troubleshooting guide problem probable cause remedy page ref. 11. Product is not feeding into the freezing cylinder. A. Inadequate level of mix in the mix hopper. A. Fill the mix hopper with mix. 17 b. Mix inlet hole frozen up. B. Mix hopper temperature needs adjustment. Contact ...

  • Page 30: Section 9

    26 models 358 & 359 parts replacement schedule section 9 parts replacement schedule part description every 3 months every 4 months every 6 months annually 358 qty. 359 qty. Drive shaft seal x 1 2 scraper blade x 2 4 freezer door gasket x 1 2 front bearing x 1 2 draw valve o-ring x 2 4 black bristle ...

  • Page 31

    27 models 358 & 359 limited warranty on equipment 131125 section 10 limited warranty on equipment taylor company limited warranty on freezers taylor company, a division of carrier commercial refrigeration, inc. (“taylor”) is pleased to provide this limited warranty on new taylor-branded freezer equi...

  • Page 32

    28 models 358 & 359 limited warranty on equipment 3. Replacement of wear items designated as class “000” parts in the taylor operator’s manual. 4. External hoses, electrical power supplies, and machine grounding. 5. Parts not supplied or designated by taylor, or damages resulting from their use. 6. ...

  • Page 33: Section 11

    29 models 358 & 359 limited warranty on parts 131125 section 11 limited warranty on parts taylor company limited warranty on taylor genuine parts taylor company, a division of carrier commercial refrigeration, inc. (“taylor”) is pleased to provide this limited warranty on new taylor genuine replacem...

  • Page 34

    30 models 358 & 359 limited warranty on parts limited warranty exceptions this limited warranty does not cover: 1. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of defective parts, replacement parts, or new parts. 2. Normal maintenance...

  • Page 35

    31 models 358 & 359 limited warranty on parts limitation of warranty this limited warranty is exclusive and is in lieu of all other warranties, conditions and/or remedies under the law, including any implied warranties or conditions of merchantability or fitness for a particular purpose. The origina...

  • Page 36

    358 063532-27 11/12/13 1 2 4 6 black blue black t1 cp t2 l1 cp l2 beater motor contactor a.O. Smith beater motor wiring steps: 1) remove brown jumper from between termi nal #1 to terminal #5 2) move blue internal (from motor main winding) from terminal #5 to terminal #6. Note: for cwle - blue intern...

  • Page 37

    358 063532-33 11/12/13 blower for water cooled only 0rn/wht wht blu wht see fig. 1 230v thermistor control board yel grn/yel pur mix out probe cold warm yel brn grn input 24 vac + - comp 1 2 7 8 nc c no mix wht/blk wht/red + - + - wht blk/wht emi filter line load l2 l2 l1 l1 230 vac 24 vac blk wht t...

  • Page 38

    359 065467-33 11/12/13 ground frame securely compressor & beater protected under primary single phasing conditions. Wht orn blk/wht wht 4 5 6 thermistor control board 3 1 auto 2 hpco switch 95 96 wash blu beater o.L. Orn auto emi filter line load l1 l1 l2 l2 a2 a1 wht/red yel yel 230 vac 24 vac wht ...