1. DL manuals
  2. Taylor
  3. Freezer
  4. 432
  5. Operator's Manual

Taylor 432 Operator's Manual

Summary of 432

  • Page 1

    Operator’s manual model 432 shake/slush freezer original operating instructions 053081-m 10/98 (original publication) (updated 8/14/14).

  • Page 2

    Complete this page for quick reference when service is required: taylor distributor: address: phone: service: parts: date of installation: information found on the data label: model number: serial number: electrical specs: voltage cycle phase maximum fuse size: a minimum wire ampacity: a e 1998 carr...

  • Page 3: Table Of Contents

    Model 432 table of contents table of contents section 1 to the installer 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installer safety 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Site p...

  • Page 4

    Model 432 table of contents table of contents - page 2 disassembly 19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Brush cleaning 20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 5: Section 1

    1 model 432 to the installer 131202 section 1 to the installer the following information has been included in the manual as safety and regulatory guidelines. For complete installation instructions, please see the installation checklist. Installer safety in all areas of the world, equipment should be...

  • Page 6

    2 to the installer model 432 131202 electrical connections this unit must be plugged into a properly grounded receptacle. The cord and plug must be sized for 20 amp usage. The voltage specifications are 208- 230/60/1. Follow specifications listed on your data plate. Follow your local electrical code...

  • Page 7

    3 model 432 to the installer 131202 refrigerant in consideration of our environment, taylor uses only hfc refrigerants. The hfc refrigerant used in this unit is r404a. This refrigerant is generally considered non-toxic and non-flammable, with an ozone depleting potential (odp) of zero (0). However, ...

  • Page 8: Section 2

    4 to the operator model 432 131202 section 2 to the operator the freezer you have purchased has been carefully engineered and manufactured to give you dependable operation. The taylor model 432, when properly operated and cared for, will produce a consistent quality product. Like all mechanical prod...

  • Page 9: Section 3

    5 model 432 safety 131202 section 3 safety we, at taylor company, are concerned about the safety of the operator at all times when they are coming in contact with the unit and its parts. Taylor makes every effort to design and manufacture built- in safety features to protect both operators and servi...

  • Page 10

    6 safety model 432 131202 an equipotential grounding lug is provided with this unit. Some countries require the grounding lug be properly attached to the rear of the frame by the authorized installer. The installation location is marked by the equipotential bonding symbol (5021 of iec 60417-1) on bo...

  • Page 11: Section 4

    7 model 432 operator parts identification section 4 operator parts identification model 432 figure 1 item description part no. 1 cover a.-hopper x52452 2 panel-rear 052363 3 panel-side-right-louvered 052527 4 panel-front-lower 052361 5 gasket-base pan 052377 6 tray a.-drip x46848 7 shield-splash 046...

  • Page 12

    8 operator parts identification model 432 120730 beater door assembly figure 2.

  • Page 13

    9 model 432 operator parts identification 120730 beater door assembly parts identification item description part no. 1 door a. - partial x39248 2 handle a. Draw x47384 3 nut-stud 029880 4 buster - ice 047735 5 o-ring - 1" od x .139 w 032504 6 valve draw - slush - ice buster 047734 7 valve a. - handl...

  • Page 14

    10 operator parts identification model 432 140814 accessories figure 3 item description part no. 1 kit a.- tune up x39969 2 brush- mix pump 3” x 7” 023316 3 pail- 10 qt. 013163 4 brush- double ended 013072 5 brush- rear bearing 1 x 2 013071 item description part no. 6 brush- draw valve 1- 1/2x3 0147...

  • Page 15: Section 5

    11 model 432 important: to the operator section 5 important: to the operator figure 4 item description 1 switch- toggle - 3 pdt 2 switch- push button - spst 3 switch- toggle- spst - 3/4 hp/250 v 4 light- amber- rect. - 12 vdc - mix out 5 light- amber- rect. - 12 vdc - add mix 6 viscosity adjustment ...

  • Page 16

    12 important: to the operator model 432 indicator light - “mix out” (item 4) a mix out indicating light is located on the front of the machine. When the light is flashing, it indicates that the hopper is empty and the mix supply needs replenishing. To prevent damage to the unit, refrigeration discon...

  • Page 17: Section 6

    13 model 432 operating procedures section 6 operating procedures the model 432 freezer is designed to produce shake or slush product at the desired thickness. This unit has a 4 quart freezing cylinder. We begin our instructions at the point where we enter the store in the morning and find the parts ...

  • Page 18

    14 operating procedures model 432 holding the beater securely, slide the beater into the freezing cylinder and align the hole at the rear of the beater with the flats on the end of the drive shaft. Slide the beater the remainder of the way into the freezing cylinder and over the end of the drive sha...

  • Page 19

    15 model 432 operating procedures rotate the draw valve so the flats on the top of the draw valve are perpendicular to the door face. Figure 13 insert the ice buster through the door spout and into the slot located just above the lower o- ring. Figure 14 with the ice buster in place, rotate the draw...

  • Page 20

    16 operating procedures model 432 step 7 position the torque arm by inserting it through the slot in the torque switch arm and down into the hole in the torque rotor which protrudes from the door. Verify proper installation by moving the torque rotor back and forth to be sure it moves freely and eas...

  • Page 21

    17 model 432 operating procedures 140814 sanitizing step 1 prepare an approved 100 ppm sanitizing solution (examples: 2- 1/2 gal. [9.5 liters] of kay- 5r or 2 gal. [7.6 liters] of stera- sheenr). Use warm water and follow the manufacturer’s specifications. Step 2 pour the sanitizing solution into th...

  • Page 22

    18 operating procedures model 432 priming step 1 with a pail beneath the door spout, move the draw handle to the right. Pour two gallons (7.6 liters) of fresh mix into the hopper and allow it to flow into the freezing cylinder. This will force out any remaining sanitizing solution. When full strengt...

  • Page 23

    19 model 432 operating procedures 140814 step 3 if local health codes permit the use of rerun, place a sanitized, nsf approved stainless steel rerun container beneath the door spout. Place the power switch in the “wash” position and move the draw handle to the right. When all the product stops flowi...

  • Page 24

    20 operating procedures model 432 brush cleaning step 1 prepare a sink with a cleaning solution (examples: kay- 5r or stera- sheenr). Use warm water and follow the manufacturer’s specific- ations. (if another approved cleaner is used, dilute according to label instructions. Important: follow the lab...

  • Page 25: Section 7

    21 model 432 important: operator checklist 080118 section 7 important: operator checklist during cleaning and sanitizing: always follow local health codes. Cleaning and sanitizing schedules are governed by federal, state, or local regulatory agencies, and must be followed accordingly. If the unit ha...

  • Page 26

    22 important: operator checklist model 432 winter storage if the place of business is to be closed during the winter months, it is important to protect the freezer by following certain precautions, particularly if the building is to be left unheated and subject to freezing conditions. Disconnect the...

  • Page 27: Section 8

    23 model 432 troubleshooting guide section 8 troubleshooting guide problem probable cause remedy page ref. 1. No product being dispensed. A. Control switch is in the “off” position. A. Place control switch in the “auto” position. 18 b. Improper mixing of product. B. Carefully follow directions for m...

  • Page 28

    24 troubleshooting guide model 432 problem probable cause remedy page ref. 4. Product too thick. A. Inadequate mix in hopper. A. Fill hopper with mix. 18 b. Improper mixing of product. B. Carefully follow directions for mixing product. - - - c. The viscosity adjustment is set incorrectly. C. Adjust ...

  • Page 29: Section 9

    25 model 432 parts replacement schedule section 9 parts replacement schedule part description every 3 months every 4 months every 6 months annually quantities to be replaced drive shaft seal x 2 drive shaft o-ring x 2 scraper blade x 2 freezer door gasket x 2 front bearing x 2 guide bearing x 2 torq...

  • Page 30

    26 limited warranty on equipment model 432 131202 section 10 limited warranty on equipment taylor company limited warranty on freezers taylor company, a division of carrier commercial refrigeration, inc. (“taylor”) is pleased to provide this limited warranty on new taylor-branded freezer equipment a...

  • Page 31

    27 model 432 limited warranty on equipment 3. Replacement of wear items designated as class “000” parts in the taylor operator’s manual. 4. External hoses, electrical power supplies, and machine grounding. 5. Parts not supplied or designated by taylor, or damages resulting from their use. 6. Return ...

  • Page 32: Section 11

    28 limited warranty on parts model 432 131202 section 11 limited warranty on parts taylor company limited warranty on taylor genuine parts taylor company, a division of carrier commercial refrigeration, inc. (“taylor”) is pleased to provide this limited warranty on new taylor genuine replacement com...

  • Page 33

    29 model 432 limited warranty on parts limited warranty exceptions this limited warranty does not cover: 1. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of defective parts, replacement parts, or new parts. 2. Normal maintenance, clean...

  • Page 34

    30 limited warranty on parts model 432 limitation of warranty this limited warranty is exclusive and is in lieu of all other warranties, conditions and/or remedies under the law, including any implied warranties or conditions of merchantability or fitness for a particular purpose. The original owner...

  • Page 35: Section 12

    Section 12 parts list 31 + available separately model 432 parts list 080619 de s cri p t io n p art num be r qty . W arr. Cl as s re m arks part s up da t e 432 s t andard (043227f000 208- 230v 60hz 1 ph) a/ c- bri sto l -r 404a accumulator- c opper 2" di a 10" lg 047062 1 103 arm- torque- 432 05245...

  • Page 36

    + available separately 32 parts list model 432 de s cri p t io n part s up da t e re m arks w arr. Cl as s qty . P art num be r bushi n g- snap 11/ 16 id x 7 /8 od 010548 1 103 com p ressor l61b562bbcb (bri s tol) 048727- 27e 1 512 208- 230/ 60/ 1 +capaci t or- run 30uf/ 370v 038487 1 103 208- 230/ ...

  • Page 37

    33 + available separately model 432 parts list 140814 de s cri p t io n part s up da t e re m arks w arr. Cl as s qty . P art num be r o -ri ng -. 291 id x .080w 018550 2 000 o -ri ng -7 /8 o d x .139w 025307 2 000 o -ri ng -1 "o d x .139w 032504 4 000 seal- dri ve shaft 032560 2 000 tool- o -r in g...

  • Page 38

    + available separately 34 parts list model 432 de s cri p t io n part s up da t e re m arks w arr. Cl as s qty . P art num be r pulley- ak49 051394 2 103 relay- 3 p o l e- 20a- 208/ 240 50/ 60 012725- 33 1 103 compressor c ontactor (p ri mary) relay- spdt- 30a- 240v 032607- 27 2 103 beater motor rel...

  • Page 39

    35 + available separately model 432 parts list de s cri p t io n part s up da t e re m arks w arr. Cl as s qty . P art num be r sw it ch- pressure 440 psi -s older 048230 1 103 sw it ch- toggle- spst 3/ 4hp/ 250v 012626 1 103 li g h t swi t ch- toggl e- 3 p dt 017184 2 103 w ash/ o ff/ auto to rq ue...

  • Page 40

    432 052145-27 11/18/13 ground frame securely left compressor relay coil auto wash off auto wash off left power switch note: static electricity may cause damage to solid state components. Eliminate static electricity by touching grounded unit before handling solid state components. L1 mix low probe m...

  • Page 41

    432 052145-33 11/18/13 ground frame securely left compressor relay coil auto wash off auto wash off left power switch note: static electricity may cause damage to solid state components. Eliminate static electricity by touching grounded unit before handling solid state components. L1 mix low probe m...

  • Page 42

    432 052145-40 11/18/13 ground frame securely left compressor relay coil auto wash off auto wash off left power switch note: static electricity may cause damage to solid state components. Eliminate static electricity by touching grounded unit before handling solid state components. L1 mix low probe m...