1. DL manuals
  2. Taylor
  3. Grill
  4. 810 Series
  5. Operator's Manual

Taylor 810 Series Operator's Manual

Manual is about: Auto Lift Grills

Summary of 810 Series

  • Page 1

    Operator's manual model 810, 812, 820, 822, 828 series auto lift grills original operating instructions 073523-m 9/15/10 (original publication) (updated 8/10/15).

  • Page 2

    Complete this page for quick reference when service is required: taylor distributor: address: phone: service: parts: date of installation: information found on data plate: model number: serial number: electrical specs: voltage cycle phase maximum fuse size: amps minimum wire ampacity: amps part numb...

  • Page 3: Table Of Contents

    Table of contents model 810, 812, 820, 822, 828 series table of contents section 1 to the installer 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installer safety 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 4

    Model 810, 812, 820, 822, 828 series table of contents table of contents - page 2 section 7 troubleshooting guide 37 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section 8 limited warranty on equipment 42 . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section 9 li...

  • Page 5: Section 1

    1 model 810, 812, 820, 822, 828 series to the installer 131205 section 1 to the installer the following information has been included in the manual as safety and regulatory guidelines. For complete installation instructions, please see the installation checklist. Installer safety in all areas of the...

  • Page 6

    2 model 810, 812, 820, 822, 828 series to the installer caution: this equipment must be properly grounded! Failure to do so can result in severe personal injury from electrical shock! This unit is provided with an equipotential grounding lug that is to be properly attached to the rear of the frame b...

  • Page 7: Section 2

    3 model 810, 812, 820, 822, 828 series to the operator 131205 section 2 to the operator the taylor grills included in this manual consist of the base model numbers 810, 812, 820, 822, and 828. Prefix letters were added to the base model numbers to denote minor design differences: l = platen length (...

  • Page 8: Section 3

    4 model 810, 812, 820, 822, 828 series safety 130211 section 3 safety we, at taylor company, are concerned about the safety of the operator when he or she comes in contact with the grill and its parts. Taylor has gone to extreme efforts to design and manufacture built-in safety features to protect b...

  • Page 9

    5 model 810, 812, 820, 822, 828 series safety 130304 important: do not use a water jet or spray excessive water on or anywhere near the grill. Failure to follow this instruction may result in serious electrical shock and cause permanent electrical and mechanical damage to internal parts. Failure to ...

  • Page 10: Section 4

    6 model 810, 812, 820, 822, 828 series operator parts identification 150114 section 4 operator parts identification l810 / g810 exploded view figure 1 item description part no. 1 can a.-grease x80925 2 slide a.-can grease left x83854 3 panel-side-upper *left 073990 4 screw-10-32x3/8 sltd trus 024298...

  • Page 11

    7 model 810, 812, 820, 822, 828 series operator parts identification 150114 l812 exploded view figure 2 item description part no. 1 can a.-grease *hem x80925 2 slide a.-can grease left x83854 3 panel-side-upper left 073990 4 screw-10-32x3/8 sltd trus 024298 5 panel-side-lower *left 073992 *6 kit a.-...

  • Page 12

    8 model 810, 812, 820, 822, 828 series operator parts identification 150114 l820 / g820 exploded view figure 3 item description part no. 1 can a.-grease hem x80925 2 slide a.-can grease left x83854 3 panel-side upper left 073990 4 screw-10-32x3/8 sltd trus 024298 5 screw 10-32 x 3/8 039381 6 panel-b...

  • Page 13

    9 model 810, 812, 820, 822, 828 series operator parts identification 150114 l822 exploded view figure 4 item description part no. 1 can a.-grease *hem x80925 2 slide a.-can grease left x83854 3 panel-side upper-lt 073990 4 screw-10-32x3/8 sltd 024298 5 screw-10-32x3/8 unsl hwh 039381 6 panel-side-lo...

  • Page 14

    10 model 810, 812, 820, 822, 828 series operator parts identification 150107 l828 / g828 exploded view figure 5 item description part no. 1 can a.-grease *hem x81942 2 panel-side upper-lt 081973 3 screw-10-32x3/8 sltd 024298 4 screw-10-32x5/8 un sl 039382 5 panel-side *left 081981 6 kit a.-grease sh...

  • Page 15

    11 model 810, 812, 820, 822, 828 series operator parts identification 150514 accessories supplied with grill figure 6 item description part no. 1 sheet-release - box of 9 080595 2 retainer-sheet release (retention bar) (qty of 3) 080594 3 clip-release material w/tab (qty of 6) 072673 item descriptio...

  • Page 16

    12 model 810, 812, 820, 822, 828 series operator parts identification 150514 optional accessories available from local taylor distributor figure 7 item description part no. 1 scraper-blade (6 pack) 073891 2 scraper-grill 073225 3 pad-cleaning (box of 10) 073737 4 holder-pad-cleaning 073736 item desc...

  • Page 17: Section 5

    13 model 810, 812, 820, 822, 828 series important: to the operator 150514 section 5 important: to the operator note: the model 810 three platen grill has been selected for illustration purposes. Figure 8 item description 1 raise button 2 standby/cook mode button 3 usb cover/connection 4 power switch...

  • Page 18: Section 6

    14 model 810, 812, 820, 822, 828 series operating procedures 130206 section 6 operating procedures the three platen model l810 has been selected to illustrate the step-by-step procedures. For grills equipped with less than three platens, perform the following steps as appropriate for your grill plat...

  • Page 19

    15 model 810, 812, 820, 822, 828 series operating procedures 130205 step 4 place the release sheet clips over the release sheet. Press them into place over the release sheet bar at the top of the platen. Figure 12 step 5 check the tightness of the release sheet against the upper platen. Figure 13 no...

  • Page 20

    16 model 810, 812, 820, 822, 828 series operating procedures 110602 care of release sheets do not: s do not fold or crease. Figure 15 s do not touch with sharp objects, grill scrapers, or abrasive pads. S do not place under other equipment or objects. S do not hot-hose or soak in water. Do: s do cle...

  • Page 21

    17 model 810, 812, 820, 822, 828 series operating procedures 150514 the control will display the word “initialization” for five seconds and then will enter the off mode, displaying the message “off”. The temperature indicators will not be illuminated. A tone will sound for 20 seconds unless the oper...

  • Page 22

    18 model 810, 812, 820, 822, 828 series operating procedures 150402 step 2 the password screen will appear. Enter the operator password “store1” and press the ok key. Figure 22 step 3 the program mode screen will appear, displaying the version of the software, motor control, and motor control boot, ...

  • Page 23

    19 model 810, 812, 820, 822, 828 series operating procedures 150406 press the menu item key to be programmed. The following screen will display. Figure 26 to edit a menu item, press the menu item key to bring up a virtual keyboard. Use the back arrow to scroll to the beginning of the name (item 1). ...

  • Page 24

    20 model 810, 812, 820, 822, 828 series operating procedures 150514 multiple timing functions: there are four timing functions for clam and flat menu items. Each function has a set of parameters associated with it. The functions currently associated with the menu item are displayed. Pressing functio...

  • Page 25

    21 model 810, 812, 820, 822, 828 series operating procedures 110603 service contact information key press the service contact information key to view the programmed service contact information. Figure 29 language key the language key is used to select the language the control will display. The avail...

  • Page 26

    22 model 810, 812, 820, 822, 828 series operating procedures 150514 step 4 enter the operator password “store1” and press the ok key. Figure 31 step 5 press the menu edit key. Figure 32 step 6 press the store menu to usb key. Figure 33 step 7 using the keyboard displayed on the control, enter a file...

  • Page 27

    23 model 810, 812, 820, 822, 828 series operating procedures 130312 patty placement & removal placement procedures of meat products must be followed on the grill. The meat must be placed on the lower grill surface from front to back. When the cook cycle is complete, the upper platen will raise. Note...

  • Page 28

    24 model 810, 812, 820, 822, 828 series operating procedures 150514 operating procedures cooking product step 1 select the menu item to be cooked. When the grill is at the correct temperature, the grill temperature indicators will be green and the control will not display any temperature statements....

  • Page 29

    25 model 810, 812, 820, 822, 828 series operating procedures 150514 flat item cook cycle screen the following is an example of a flat item cook cycle screen. The first line function default is remove in. Figure 38 to edit a menu item, press the menu item key to bring up a virtual keyboard. Press the...

  • Page 30

    26 model 810, 812, 820, 822, 828 series operating procedures 150529 one function cook cycle screen the following is an example of a one function cook cycle screen. The first line function default is remove in. Note: the sec, alarm, and gap must be set. Figure 42 two function cook cycle screen the fo...

  • Page 31

    27 model 810, 812, 820, 822, 828 series operating procedures 150529 note: if the standby alert mode is active and the alarm is sounding, the standby button must be pressed 3 times, with a one second pause between presses. The first press cancels the alarm and the second two presses lower the upper p...

  • Page 32

    28 model 810, 812, 820, 822, 828 series operating procedures cleaning after each run of product step 1 using the grill scraper, scrape the grease on the lower grill surface from front to back. Do not scrape across the rear of the lower grill surface with the grill scraper. Figure 49 step 2 use the w...

  • Page 33

    29 model 810, 812, 820, 822, 828 series operating procedures 150514 caution: never use force to raise the upper platen. Damage to components may result. Only use the raise button to open the upper platen! Note: do not turn the power switch to the off position while the platens are in the “down” posi...

  • Page 34

    30 model 810, 812, 820, 822, 828 series operating procedures 150304 step 6 remove the release sheet clip, the release sheet retainer, and the release sheet. Take them to the sink area. Place the release sheet on a clean, flat surface next to the sink. Figure 56 step 7 repeat steps 1 through 6 for th...

  • Page 35

    31 model 810, 812, 820, 822, 828 series operating procedures 130201 step 13 using an approved high temperature grill cleaner, pour approximately 3 oz. (90 ml) onto each 12” (305 mm) cook zone. Figure 61 step 14 firmly attach the non-abrasive pad to the grill cleaning pad holder. Important! Use the g...

  • Page 36

    32 model 810, 812, 820, 822, 828 series operating procedures 110610 step 19 apply grill cleaner to the back side of the upper platens. Figure 65 step 20 apply grill cleaner to the outer edges of the right and left platens. Step 21 press the standby button twice to lower one of the platens. 810 only:...

  • Page 37

    33 model 810, 812, 820, 822, 828 series operating procedures 130201 step 32 with a clean, sanitizer-soaked grill cloth, rinse the bottom of the platen handles, and the front, sides, and back of the platen surfaces. Figure 68 step 33 with a clean, sanitizer-soaked grill cloth, rinse the platen cook s...

  • Page 38

    34 model 810, 812, 820, 822, 828 series operating procedures important! Do not use a jet of water to clean or rinse the grill. Do not use cold water or ice to cool the upper platen or the lower cook surface. Failure to follow these instructions may result in: s serious electrical shock s burns from ...

  • Page 39

    35 model 810, 812, 820, 822, 828 series operating procedures 150304 step 42 place the release sheets flat on the lower grill surface. Gently clean both sides of the sheets with an approved high temperature grill cleaner and the grill cleaning pad and holder. Figure 73 step 43 rinse both sides of the...

  • Page 40

    36 model 810, 812, 820, 822, 828 series operating procedures 120830 non-24 hour stores only: step 50 apply a light coat of vegetable oil to the entire lower grill surface. Figure 77 step 51 leave the upper platens in the open position overnight. Step 52 place the power switch in the off position. Fi...

  • Page 41: Section 7

    37 model 810, 812, 820, 822, 828 series troubleshooting guide 150514 section 7 troubleshooting guide problem probable cause remedy 1. One side of the grill will not heat. The screen will display, “call service. No heat in zone (indicates specific zone) main power off & retry.” a. One of the power co...

  • Page 42

    38 model 810, 812, 820, 822, 828 series troubleshooting guide 150514 problem probable cause remedy 5. The upper platen will not stay in the standby mode, but will stay in the cook position. A. Incorrect use of the standby button. The standby button may have been pressed twice too quickly. A. Press t...

  • Page 43

    39 model 810, 812, 820, 822, 828 series troubleshooting guide 150514 problem probable cause remedy 10. The display reads “upper platen stuck. Call service-latch. If the platen is open, cook flat items only.” a. The arm bearings are dirty. A. Call a service technician. B. The air cylinder is faulty. ...

  • Page 44

    40 model 810, 812, 820, 822, 828 series troubleshooting guide 150514 problem probable cause remedy 12. The product is under-cooked or overcooked. (cont'd.) h. Cooking procedures may have been followed incorrectly. H. Ensure that the product was removed immediately after the cook cycle ended. Double ...

  • Page 45

    41 model 810, 812, 820, 822, 828 series troubleshooting guide 150514 problem probable cause remedy 14. The product is not cooking evenly. (cont'd.) e. The product is out of specification. E. Product must be within specification (proper thickness, shape, etc.). F. The platen is not level. F. Call a s...

  • Page 46: Section 8

    42 model 810, 812, 820, 822, 828 series limited warranty on equipment 131205 section 8 limited warranty on equipment taylor company limited warranty on crown series grills taylor company, a division of carrier commercial refrigeration, inc. (“taylor”) is pleased to provide this limited warranty on n...

  • Page 47

    43 model 810, 812, 820, 822, 828 series limited warranty on equipment 141020 4. Replacement of the product’s cooking surfaces, including the upper platen and lower plate, due to pitting or corrosion (or in the case of the upper platen, due to loss of plating) as a result of damage due to the impact ...

  • Page 48

    44 model 810, 812, 820, 822, 828 series limited warranty on equipment limitation of warranty this limited warranty is exclusive and is in lieu of all other warranties, conditions and/or remedies under the law, including any implied warranties or conditions of merchantability or fitness for a particu...

  • Page 49: Section 9

    45 model 810, 812, 820, 822, 828 series limited warranty on parts 131205 section 9 limited warranty on parts taylor company limited warranty on taylor genuine parts taylor company, a division of carrier commercial refrigeration, inc. (“taylor”) is pleased to provide this limited warranty on new tayl...

  • Page 50

    46 model 810, 812, 820, 822, 828 series limited warranty on parts limited warranty exceptions this limited warranty does not cover: 1. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of defective parts, replacement parts, or new parts. 2...

  • Page 51

    47 model 810, 812, 820, 822, 828 series limited warranty on parts limitation of warranty this limited warranty is exclusive and is in lieu of all other warranties, conditions and/or remedies under the law, including any implied warranties or conditions of merchantability or fitness for a particular ...