1. DL manuals
  2. Taylor
  3. Grill
  4. C819
  5. Operating Instructions Manual

Taylor C819 Operating Instructions Manual

Manual is about: Auto Lift Grill

Summary of C819

  • Page 1

    Models c819 & c821 auto lift grills original operating instructions 073946-m 5/10/11 (original publication) (updated 10/14/11).

  • Page 2

    Complete this page for quick reference when service is required: taylor distributor: address: phone: service: parts: date of installation: information found on data plate: model number: serial number: electrical specs: voltage cycle phase maximum fuse size: amps minimum wire ampacity: amps part numb...

  • Page 3: Table Of Contents

    Table of contents models c819 & c821 table of contents section 1 to the installer 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installer safety 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 4

    Models c819 & c821 table of contents table of contents - page 2 loading menu items from usb 19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating procedures 21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D...

  • Page 5: Section 1

    1 models c819 & c821 to the installer section 1 to the installer the following are general installation instructions. For complete installation details, please see the checkout card. Installer safety in all areas of the world, equipment should be installed in accordance with existing local codes. Pl...

  • Page 6

    2 models c819 & c821 to the installer caution: this equipment must be properly grounded! Failure to do so can result in severe personal injury from electrical shock! This unit is provided with an equipotential grounding lug that is to be properly attached to the rear of the frame by the authorized i...

  • Page 7: Section 2

    3 models c819 & c821 to the operator section 2 to the operator the grill you have purchased has been carefully engineered and manufactured to provide dependable operation. This grill, when properly operated and maintained, will produce a consistent quality product. Like all mechanical products, it w...

  • Page 8: Section 3

    4 models c819 & c821 safety section 3 safety we, at taylor company, are concerned about the safety of the operator when he or she comes in contact with the grill and its parts. Taylor has gone to extreme efforts to design and manufacture built-in safety features to protect both you and the service t...

  • Page 9

    5 models c819 & c821 safety this appliance must be isolated from all combustible construction and materials including, but not limited to: walls, partitions, furniture, floors, curtains, paper, boxes, and decorations. Failure to comply may result in a fire and cause destruction and severe injury. Fo...

  • Page 10

    6 models c819 & c821 safety this piece of equipment is made in america and has american sizes on hardware. All metric conversions are approximate and vary in size. Noise level: airborne noise emission does not exceed 70 db(a) when measured at a distance of 1.0 meter from the surface of the machine a...

  • Page 11: Section 4

    7 models c819 & c821 operator parts identification 110902 section 4 operator parts identification c819 figure 1 item description part no. 1 can a.-grease x73944 2 slide-grease can 073293 3 panel-side upper-left 073990 4 screw-10-32x3/8 sltd trus 024298 5 panel-side-lower-left 073992 6 platen a.-serv...

  • Page 12

    8 models c819 & c821 operator parts identification 110902 c821 figure 2 item description part no. 1 can a.-grease x73944 2 slide-grease can 073293 3 panel-side upper-left 073990 4 screw-10-32x3/8 sltd trus 024298 5 panel-side-lower-left 073992 6 platen a.-service x73741-23 7 panel a.-back service x6...

  • Page 13

    9 models c819 & c821 operator parts identification 110602 accessories figure 3 item description part no. 1 sheet-release (box 9) 073442 *2 retainer-sheet release (retention bar) 072845 **3 clip-release material w/tab 072673 4 scraper-teflon wiper 075887 item description part no. 5 strip-replacement ...

  • Page 14: Section 5

    10 models c819 & c821 important: to the operator section 5 important: to the operator figure 4 item description 1 raise button 2 standby/cook mode button 3 master power switch 4 cover a.-usb 5 clean mode key item description 6 program key 7 temperature indicator lights 8 power key 9 function display...

  • Page 15: Section 6

    11 models c819 & c821 operating procedures 110531 section 6 operating procedures the models c819 and c821 are 24” (610 mm) grills. The c819 is equipped with two independent 12” (305 mm) upper platens and the model c821 is equipped with one independent 12” (305 mm) upper platen. These grills are capa...

  • Page 16

    12 models c819 & c821 operating procedures step 3 hold the non-hemmed end of the release material sheet. Gently pull the sheet tight, wrapping it around the platen in a side-to-side manner. Figure 7 note: check the alignment of the release material sheet and make sure it fits smoothly over the upper...

  • Page 17

    13 models c819 & c821 operating procedures 110602 the release material must be replaced when: s cleaning procedures fail to remove all buildup and product sticks to the release material. S a tear appears in the cooking area of the release material, causing product to stick to the release material. F...

  • Page 18

    14 models c819 & c821 operating procedures 110602 important! Clean the release sheets using the grill cleaning pad and holder identified on page 9 only. Using any other pad and holder will damage the release sheets. Figure 12 note: contact your local taylor distributor to purchase the grill cleaning...

  • Page 19

    15 models c819 & c821 operating procedures step 2 touch a menu key on the control to start the grill. The grill will start heating up to the proper temperature. The control will display the selected menu item and indicate “bottom too cool” and “top too cool”. The grill temperature indicators will be...

  • Page 20

    16 models c819 & c821 operating procedures programming menu items to enter the program mode, the grill control must be in the off or idle mode. Step 1 press and hold the program key for approximately five seconds to enter the program mode. Figure 18 step 2 the password screen will appear. Enter the ...

  • Page 21

    17 models c819 & c821 operating procedures menu edit key the menu edit key is used to program a menu item. When the menu edit key is pressed, the following screen will display. Figure 22 if there is more than one screen of menu items, press the previous or next arrow keys to access the other menu it...

  • Page 22

    18 models c819 & c821 operating procedures 110603 multiple timing functions: there is one timing function for clam items and a maximum of 3 timing functions for each flat menu item. Each function has a set of parameters associated with it. The function currently associated with the menu item is disp...

  • Page 23

    19 models c819 & c821 operating procedures 110603 step 5 press the menu edit key. Figure 28 step 6 press the store menu to usb key. Figure 29 step 7 enter a file name (up to 8 characters) to save the menu items, using the keyboard displayed on the control. Press the ok key. The menu items are saved ...

  • Page 24

    20 models c819 & c821 operating procedures patty placement placement procedures of meat products must be followed on the grill. Meat must be placed on the lower grill surface from front to back. When the cook cycle is complete, the upper platen will raise. Note: it is very important that all patties...

  • Page 25

    21 models c819 & c821 operating procedures operating procedures cooking product step 1 select the menu item to be cooked. The grill is at the correct temperature if the control does not display any temperature statements and the grill temperature indicators are green. Step 2 quickly place the produc...

  • Page 26

    22 models c819 & c821 operating procedures standby procedures whenever the grill is idle and product is not being cooked, the upper platen must be placed in the standby position. Step 1 to place the upper platen in the standby position, press the standby button twice from the open position. Figure 3...

  • Page 27

    23 models c819 & c821 operating procedures step 2 use the wiper squeegee to clean the release material sheet on the upper platen. Use a diagonal motion to clean the sheet. Hold the handle at a slight upward angle, with the wiper end facing downward. Figure 37 note: do not use excessive pressure when...

  • Page 28

    24 models c819 & c821 operating procedures step 2 press the clean key. When the cook surfaces reach the proper temperature for cleaning, an alarm will sound and the message “ready to clean” will be displayed. Figure 39 step 3 press the raise button to cancel the alarm. Figure 40 step 4 put on heat-r...

  • Page 29

    25 models c819 & c821 operating procedures step 6 remove the release material clip, release sheet retainer, and the release material sheet. Take these parts to the sink to be washed and rinsed. Figure 43 step 7 repeat steps 1 through 6 for the remaining upper platen. Step 8 wash and rinse the clips ...

  • Page 30

    26 models c819 & c821 operating procedures 110602 step 13 using an approved high temperature grill cleaner, pour approximately 3 oz. (90 ml) onto each 12” (305 mm) cook zone. Figure 48 step 14 firmly attach the non-abrasive pad to the grill cleaning pad holder. Important! Use the grill cleaning pad ...

  • Page 31

    27 models c819 & c821 operating procedures 110602 step 23 lightly scrub the front side of the platens with the non-abrasive pad until all soil has been liquified by the grill cleaner. For stubborn soils, apply additional grill cleaner and lightly scrub. Do not rinse the platens at this time. Step 24...

  • Page 32

    28 models c819 & c821 operating procedures 110602 step 37 lightly scrub the surface with the non-abrasive pad until all soil has been liquified by the grill cleaner. Figure 56 note: the rear of the upper platen, as well as the tubular arm, can easily be wiped from the front of the unit. If cleaning ...

  • Page 33

    29 models c819 & c821 operating procedures 110602 important! Step 40 must be performed using the grill cleaning pad and holder indentified on page 9, only. Using any other pad and holder will damage the release material sheets. Note: contact your local taylor distributor to purchase the correct gril...

  • Page 34

    30 models c819 & c821 operating procedures non-24 hour stores only: step 46 wipe all areas with a clean, sanitizer-soaked grill cloth. Step 47 wipe all exterior panels. Step 48 apply a light coat of vegetable oil to the entire lower grill surface. Figure 63 step 49 leave the upper platens in the ope...

  • Page 35: Section 7

    31 models c819 & c821 troubleshooting guide section 7 troubleshooting guide problem probable cause remedy 1. One side of the grill will not heat. The control will display the message, “faulty element or shorted probe” after the too cool timer has elapsed. A. The heater is faulty. A. Call a service t...

  • Page 36

    32 models c819 & c821 troubleshooting guide problem probable cause remedy 6. The upper platen will not stay in the cook or standby position. A. Temperature is insufficient to satisfy the indicator led's. A. Wait until the indicator led's turn green. B. The control harness is faulty. B. Call a servic...

  • Page 37

    33 models c819 & c821 troubleshooting guide problem probable cause remedy 12. The product is under-cooked or overcooked. A. The release material sheet is worn. A. Replace the release material sheet. B. Incorrect cooking time. B. Reset the processor control for the correct time. C. Incorrect temperat...

  • Page 38

    34 models c819 & c821 troubleshooting guide problem probable cause remedy 16. The display reads “home switch not seen.” a. Defective motor control. A. Call a service technician. B. Defective stepper motor. B. Call a service technician. C. Defective stepper motor wire harness. C. Call a service techn...

  • Page 39: Section 8

    Section 8 parts list 35 models c819 & c821 parts list 111014 + available separately c81923n879 - 208v 60hz 3 ph - natural gas - canada & c 82123nw 3 9 - 208v 60h z 3 ph - natural gas - 1 p laten l eft - rohs compli ant de s cri p t io n p art num be r c819 qty . C821 qty . W arr. Cl as s re m arks a...

  • Page 40

    36 parts list models c819 & c821 + available separately de s cri p t io n re m arks w arr. Cl as s c821 qty . C819 qty . P art num be r +sli de- g rease can 073293 2 2 103 card- checkout g en mkt inf gap 073484 1 1 000 cable- platen- f -r ear 073251 4 2 103 cable- platen- f ront 073252 4 2 103 caste...

  • Page 41

    37 models c819 & c821 parts list + available separately de s cri p t io n re m arks w arr. Cl as s c821 qty . C819 qty . P art num be r deflecto r a .- flue *c 819* x69657 1 1 103 di ag ram -w iri ng *c 819* 073814- 23 1 000 di ag ram -w iri ng *c 821* 069842- 23 1 000 e- ri ng 1/ 4 b lack phos 0321...

  • Page 42

    38 parts list models c819 & c821 + available separately de s cri p t io n re m arks w arr. Cl as s c821 qty . C819 qty . P art num be r harness- id c b oard 073429- l 1 1 103 harness- id c b oard 073429- r 1 1 103 harness- ig ni ti on- g round * 069757 1 1 103 harness- pcb/ gr sw it ch 072529 2 2 10...

  • Page 43

    39 models c819 & c821 parts list + available separately de s cri p t io n re m arks w arr. Cl as s c821 qty . C819 qty . P art num be r label- inst- li ght* 15e* f ren 079567- f 1 1 000 label- n oti c e- casters- canada 076389- can 1 1 000 label- w arn- gas g ri ll- cana 078075- can 1 1 000 label- w...

  • Page 44

    40 parts list models c819 & c821 + available separately de s cri p t io n re m arks w arr. Cl as s c821 qty . C819 qty . P art num be r panel a. -c ontrol upper *c 819 x73816 2 103 panel a. -l ig ht *c 819* x73881 1 103 panel a. -s id e u pper- l t x72962 1 103 panel a. -s id e u pper- r t x72965 1 ...

  • Page 45

    41 models c819 & c821 parts list + available separately de s cri p t io n re m arks w arr. Cl as s c821 qty . C819 qty . P art num be r screw -1/ 4- 20x3/ 8 s ltd r o und 011694 15 30 000 screw -1/ 4- 20x5/ 8 serrated h w h 017522 23 17 000 screw -10- 24x1/ 2 t o r x t russ t 20 002077 4 4 000 screw...

  • Page 46

    42 parts list models c819 & c821 + available separately de s cri p t io n re m arks w arr. Cl as s c821 qty . C819 qty . P art num be r spri n g- extensi on latch 072617 8 4 000 +pi n -spri n g u pper 072542 4 2 000 supply- pow e r- 10w 12vdc 073336 2 2 103 sw it ch a. -l atch x73775 2 2 103 sw it c...

  • Page 47

    43 models c819 & c821 parts list + available separately de s cri p t io n re m arks w arr. Cl as s c821 qty . C819 qty . P art num be r valve- solenoi d 3 w ay 12 vdc 072695- 1 2 1 103 vari s tor a .- 230vac w /#10 spade x51733- c 2 2 103 wi n d o w- f r on t v ie w p or t 073013 2 2 103 +lens- mi c...

  • Page 48

    C819 073814-23 9/11.

  • Page 49

    C821 069842-23 9/11.