- DL manuals
- Taylor
- Freezer
- PH90
- Operating Instructions Manual
Taylor PH90 Operating Instructions Manual - page 66
62
Model PH90
Important: Operator Checklist
080221
Winter Storage
If the place of business is to be closed during the winter
months, it is important to protect the freezer by
following certain precautions, particularly if the
building is to be left unheated and subject to freezing
conditions.
Disconnect the freezer from the main power source to
prevent possible electrical damage.
On water cooled freezers, disconnect the water
supply. Use air pressure to blow out any water
remaining in the condensers. This is extremely
important. Failure to follow this procedure may cause
severe and costly damage to the refrigeration system.
Your local Taylor Distributor can perform this service
for you.
Wrap detachable parts of the freezer such as beater
assembly and freezer door, and place in a protected
dry place. Rubber trim parts and gaskets can be
protected by wrapping with moisture--proof paper. All
parts should be thoroughly cleaned of dried mix or
lubrication accumulations which attract mice and other
vermin.
Summary of PH90
Page 1
Model ph90 combination freezer operating instructions 047772-m 2/00
Page 2
Complete this page for quick reference when service is required: taylor distributor: address: phone: service: parts: date of installation: information found on data plate: model number: serial number: electrical specs: voltage cycle phase maximum fuse size: amps minimum wire ampacity: amps part numb...
Page 3: Table Of Contents
Model ph90 table of contents table of contents section 1 to the installer 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installer safety 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Site ...
Page 4
Table of contents model ph90 table of contents -- page 2 manual brush cleaning 55 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Draining product from the freezing cylinder 55 . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rinsing 56 . . . . ...
Page 5: Section 1
1 model ph90 to the installer 081210 section 1 to the installer the following are general installation instructions. For complete installation details, please see the check out card. Installer safety in all areas of the world, equipment should be installed in accordance with existing local codes. Pl...
Page 6
2 model ph90 to the installer 081210 air cooled units do not obstruct air intake and discharge openings: air cooled units require a minimum of 3” (76 mm) of clearance around all sides of the freezer to allow for adequate air flow across the condensers. Install the deflector provided to prevent recir...
Page 7
3 model ph90 to the installer 081210 beater rotation beater rotation must be clockwise as viewed looking into the freezing cylinder. Note: the following procedures must be performed by an authorized taylor service technician. To correct rotation on a three--phase unit, interchange any two incoming p...
Page 8: Section 2
4 model ph90 to the operator 081210 section 2 to the operator the freezer you have purchased has been carefully engineered and manufactured to give you dependable operation. The taylor model ph90, when properly operated and cared for, will produce a consistent quality product. Like all mechanical pr...
Page 9: Section 3
5 model ph90 safety 081210 section 3 safety we at taylor company are concerned about the safety of the operator when he or she comes in contact with the freezer and its parts. Taylor has gone to extreme efforts to design and manufacture built--in safety features to protect both you and the service t...
Page 10
6 model ph90 safety 081210 s do not allow untrained personnel to operate this machine. S do not operate the freezer unless all service panels and access doors are restrained with screws. S do not remove any internal operating parts (examples: freezer door, beater, scraper blades, etc.) unless all co...
Page 11: Section 4
7 model ph90 operator parts identification section 4 operator parts identification.
Page 12
8 model ph90 operator parts identification ph90 exploded view parts identification item description part no. 1 cover a.-hopper x42628-ser 1a knob-mix cover 025429 1b retainer-hopper cover 042619 1c screw-8-32 x 1/2 oval hd 043295 2 agitator x44797 3 pan-drip heat treat 048204 4 panel-rear 048208 5 l...
Page 13
9 model ph90 operator parts identification 091216 beater door assembly -- shake side item description part no. 1 shaft--beater--7 qt. Flute 050985 2 blade--scraper 041103 3 seal--drive shaft 032560 4 bearing--door--front 055605 5 o--ring -- freezer door 033493 6 door a.--1 spt--4 flv--ht x55724--ser...
Page 14
10 model ph90 operator parts identification beater door assembly -- soft serve side item description part no. 1 seal--drive shaft 032560 2 drive shaft 032564 3 beater a. X46231 4 clip--scraper blade 046236 5 scraper blade 046235 *6a bearing--front 050348 6b shoe--front helix--rear 050346 6c shoe--fr...
Page 15
11 model ph90 operator parts identification air/mix pump -- shake side & soft serve sides item description part no. 1 -- 13 pump a.--coax--shake x45788--a pump a.--coax--soft srv x45316--b 1 tube a.--mix inlet x45318 2 seal--air inlet fitting 045327 3 o--ring--mix inlet fitting 015835 4 spring--tape...
Page 16
12 model ph90 operator parts identification pump a.--syrup--heated x53800--brn/tan item description part no. 1 plunger a.-pump x36576-brn plunger a.-pump x36576-tan 1a knob-plunger-brown 032762-brn knob-plunger-tan 032762-tan 1b o-ring 9/16 od 016369 1c nut-plunger 036577 1d tube-plunger 032757 1e i...
Page 17
13 model ph90 operator parts identification syrup tank item description part no. 1 syrup tank (4 qt./3.8 liter) 045533 1a syrup tank cover 035759--1 *1b tip--nylon--white 042747 tip--nylon--grey 024261 1c gasket--syrup tank cover 016037 1d dip tube 015441--7 1d--1 o--ring--dip tube 018550 1e washer ...
Page 18
14 model ph90 operator parts identification accessories item description part no. 1 sanitizer kay-5 (125 packs) 041082 2 lubricant-taylor hi-perf. 048232 3 kit - tune up x49463-12 4 pail-mix 10 qt. 013163 5 brush-set lvb 050103 6 brush-rear brg 1 in.Dx2 in 013071 7 brush-double ended 013072 item des...
Page 19: Section 5
15 model ph90 important: to the operator section 5 important: to the operator item description 1 power switch (toggle) 2 indicator lights (pcb a.--led) 3 flavor selector keypad (switch--membrane) 4 liquid crystal display 5 keypads (switch--membrane) 6 heater switches (toggle) symbol definitions to b...
Page 20
16 model ph90 important: to the operator power switch the power switch is located under the control panel on the left hand side of the unit. When placed in the on position, the power switch allows softech panel operation. Indicator lights mix low -- when the mix low light begins to flash, it indicat...
Page 21
17 model ph90 important: to the operator adjustable draw handle the soft serve side of the freezer features an adjustable draw handle to provide the best portion control, giving a better, consistent quality to your product and controlling costs. The draw handle should be adjusted to provide a flow r...
Page 22
18 model ph90 important: to the operator 010917 this display indicates the freezer is operating in 3 different modes. The following information is given: the left side of the freezer is operating in the standby mode, and the mix level in the hopper is out. The right side is operating in the wash and...
Page 23
19 model ph90 important: to the operator the next display is the screen which will appear after the failure message. To comply with health codes, heat treatment system freezers must complete a heat treatment cycle daily, and must also be brushed cleaned every 14 days. Brush cleaning is the normal di...
Page 24
20 model ph90 important: to the operator if the wash keypad is pressed, the next display will appear and the freezer will have to be disassembled and brush cleaned. Off :mode: off ok :mix: ok 41.0f hopper 41.0f freezer locked once the freezer is unlocked by starting a heat treatment cycle, only the ...
Page 25
21 model ph90 important: to the operator screen “c” is set clock. This screen will display the current date and time. The date and time may only be changed after the freezer has been manually brush cleaned but before it has been placed in the auto mode. Move the cursor under the number you wish to c...
Page 26
22 model ph90 important: to the operator screen “g” is heat cycle data. The information from the previous heat treatment cycles can be obtained through this screen. The most recent heat treatment cycle data will be shown first; press the plus keypad to scroll through the remaining heat cycle display...
Page 27: Section 6
23 model ph90 operating procedures section 6 operating procedures equipment set up evaluate the condition of lights and screen messages (hard lock or soft lock, etc.) before performing opening procedures. If all four led’s on the front of the unit are lit, the unit is locked. (see figure 1.) figure ...
Page 28
24 model ph90 operating procedures check scraper blades for any nicks or signs of wear. If any nicks are present, replace the blades. Note: scraper blades should be replaced every 6 months. If blades are in good condition, place each scraper blade over the holding pins on the beater assembly. (see f...
Page 29
25 model ph90 operating procedures step 4 assemble the draw valve spinner assembly. Inspect draw valve o--rings for cuts or nicks. (replace if cut or nicked.) if draw valve o--rings are in good condition, slide the two o--rings into the grooves of the draw valve and lubricate. (see figure 8.) figure...
Page 30
26 model ph90 operating procedures install the draw valve spinner assembly. Insert the draw valve from the bottom until the slot in the draw valve which accepts the draw handle comes into view. (see figure 13.) figure 13 step 6 install and lubricate the pivot pin o--ring. (see figure 14.) figure 14 ...
Page 31
27 model ph90 operating procedures insert the spinner blade shaft from the bottom, into the center of the driven spinner, and up through the draw valve cavity until the shaft appears at the top of the draw valve. The spinner blade must be aligned and engaged to the driven spinner at the bottom. This...
Page 32
28 model ph90 operating procedures insert the drive shaft through the rear shell bearing in the freezing cylinder and engage the hex end firmly into the drive coupling. (see figure 21.) figure 21 step 2 install the beater assembly. First check the scraper blades for any nicks or signs of wear. If an...
Page 33
29 model ph90 operating procedures step 2 assemble the freezer door. Place the door gasket into the groove on the back of the freezer door. Slide the front bearing over the baffle rod so the flanged edge is against the door. Do not lubricate the gasket or bearing. (see figure 26.) figure 26 step 3 i...
Page 34
30 model ph90 operating procedures step 5 slide the o--ring into the groove on the pivot pin and lubricate. (see figure 31.) figure 31 install the draw handle. Slide the fork of the draw handle in the slot of the draw valve. Secure with pivot pin. (see figure 32.) figure 32 note: the soft serve side...
Page 35
31 model ph90 operating procedures install the two notched drip pans in the left and right side panels. (see figure 35.) figure 35 step 8 install the front drip tray and splash shield under the door spouts. (see figure 36.) figure 36 mix hopper assembly to assemble the mix hopper for both sides of t...
Page 36
32 model ph90 operating procedures note: check rings have two smooth surfaces. A concave shape indicates an incorrect assembly. Turn the check ring inside out to correctly expose the flat surface. (see figure 39.) figure 39 step 4 lightly lubricate the inside wall of the piston with a paper thin lay...
Page 37
33 model ph90 operating procedures insert the already assembled piston and valve body into the bottom of the pump cylinder. (see figure 43.) figure 43 note: the drive hole in the piston must be visible through the drive hole opening in the pump cylinder and the aligning ball located at the base of t...
Page 38
34 model ph90 operating procedures step 8 install one o--ring on each end of the mix feed tube, and thoroughly lubricate. (see figure 48.) figure 48 step 9 lay the pump assembly, pump clip, mix feed tube and cotter pin in the bottom of the mix hopper for sanitizing. Lay the agitator in the bottom of...
Page 39
35 model ph90 operating procedures 081210 sanitizing -- shake side step 1 prepare a pail of approved 100 ppm sanitizing solution (examples: 2--1/2 gal. [9.5 liters] of kay--5r or 2 gal. [7.6 liters] of stera--sheenr). Use warm water and follow the manufacturer’s specifications. Step 2 pour the sanit...
Page 40
36 model ph90 operating procedures step 10 with a pail beneath the door spout, open the draw valve and press the pump keypad. Open and close the draw valve six times. Open the draw valve and draw off 2 quarts (1.9 liters) of sanitizing solution. Remove the vinyl sanitizing tube from the air/mix pump...
Page 41
37 model ph90 operating procedures 081210 sanitizing -- soft serve side step 1 prepare a pail of approved 100 ppm sanitizing solution (examples: 2--1/2 gal. [9.5 liters] of kay--5r or 2 gal. [7.6 liters] of stera--sheenr). Use warm water and follow the manufacturer’s specifications. Step 2 pour the ...
Page 42
38 model ph90 operating procedures step 10 press the wash and pump keypads and close the draw valve. (see figure 59.) figure 59 note: be sure your hands are clean and sanitized before going on in these instructions. Step 11 press the cal keypad and place the agitator on the agitator drive shaft hous...
Page 43
39 model ph90 operating procedures priming -- shake side note: evaluate the condition of led’s (lights) and screen messages before performing priming procedures. If all 4 led’s are flashing, the unit is locked. Step 1 with a mix pail beneath the door spout, open the draw valve. Pour 2--1/2 gallons (...
Page 44
40 model ph90 operating procedures 080221 priming -- soft serve side step 1 with a mix pail beneath the door spout, open the draw valve. Pour 2--1/2 gallons (9.5 liters) of fresh mix into the mix hopper and allow it to flow into the freezing cylinder. This will force out any remaining sanitizing sol...
Page 45
41 model ph90 operating procedures step 3 important: install the agitator back onto the agitator drive shaft housing. Replace the hopper cover. (see figure 66.) figure 66 step 4 remove the syrup lines from the freezer door. Step 5 return to the freezer with a small amount of cleaning solution. With ...
Page 46
42 model ph90 operating procedures 010917 place the spout cap o--ring in the spout cap. Fill the spout cap with sanitizing solution. While holding the draw valve closed, install the spout cap over the end of the door spout. This will cause sanitizing solution to back flow through the syrup ports. (s...
Page 47
43 model ph90 operating procedures 080221 rinse these parts in cool, clean water. Prepare a small amount of an approved cleaning solution (example: kay--5r or stera--sheenr). Use warm water and follow the manufacturer’s speci- fications and brush clean the parts. Place the design cap on a clean, dry...
Page 48
44 model ph90 operating procedures 080221 caution: do not draw product during the heating cycle because of high product temperatures. When the heating cycle is complete, the control will return to the standby mode. There are 3 phases of the heat cycle: heating, holding and cooling. Each phase has a ...
Page 49
45 model ph90 operating procedures step 3 return to the freezer with a small amount of sanitizing solution. With a pail below the door spout, dip the door spout brush into the sanitizing solution and brush clean the syrup ports in the freezer door, door spout, bottom of the driven spinner and spinne...
Page 50
46 model ph90 operating procedures 080221 step 4 when ready to resume normal operation, press the auto keypad. (see figure 81.) note: this procedure should be done 3--4 hours before the first shake is served, to build up ice crystals. Figure 81 soft serve side step 1 prepare a small amount of an app...
Page 51
47 model ph90 operating procedures step 3 when ready to resume normal operation, press the auto keypad. (see figure 84.) note: this procedure should be done 15 minutes before product is expected to be served. Figure 84 syrup system two main objectives in your opening procedures must be to: (1) fill ...
Page 52
48 model ph90 operating procedures remove the syrup tank from the compartment. Remove the syrup tank lid by lifting up on the locking lever. Fill the syrup tank with syrup to the indicating mark on the label. Do not overfill the tanks. (see figure 88.) figure 88 replace the tank lid, match and conne...
Page 53
49 model ph90 operating procedures press the wash keypad. This will bleed any air pockets from the syrup line. When a steady stream of syrup is flowing into the cup, press the cal keypad to stop the syrup flow. Discard the syrup in the cup. (see figure 93.) figure 93 hold the small portion of the ca...
Page 54
50 model ph90 operating procedures attach the syrup lines to the freezer door. Insert the syrup line fitting into the syrup port in the freezer door. The flat side of the syrup line fitting must be aligned with the pin in the syrup port. Rotate the syrup line fitting upward to lock in place. (see fi...
Page 55
51 model ph90 operating procedures step 7 remove the plunger tube and the insert from the plunger assembly. (see figure 100.) figure 100 step 8 remove the spring and washer from the plunger assembly. (see figure 101.) figure 101 step 9 remove the seal assembly from the plunger assembly. (see figure ...
Page 56
52 model ph90 operating procedures step 14 remove the discharge tube from the valve body. (see figure 106.) figure 106 step 15 remove the 1--5/16” o--ring from the valve body, and remove the 1” o--ring from the discharge tube. Cleaning the syrup pump step 1 flush and rinse the pump in a container of...
Page 57
53 model ph90 operating procedures step 8 insert the brush, by the non--bristle end, into the passageway between the inlet valve and the outlet valve. (see figure 110.) figure 110 step 9 move the brush back and forth to scrub this passageway. Advance the brush completely, and pull the brush out of t...
Page 58
54 model ph90 operating procedures step 4 install the plunger insert into the plunger tube by positioning the end of the insert with the beveled edge and smaller hole to enter into the plunger tube first. Step 5 install the plunger nut onto the plunger tube. Step 6 install the knob o--ring into the ...
Page 59
55 model ph90 operating procedures step 12 install the cylinder onto the larger opening in the valve body by tilting the cylinder away from the discharge tube and sliding the widest section of flange under the center locking groove on the valve body. Align the tabs on the cylinder with the locking g...
Page 60
56 model ph90 operating procedures step 5 with a pail under the door spout, press the wash and pump keypads. Open the draw valve and start to drain the product from the freezing cylinder and mix hopper. (see figure 121.) figure 121 step 6 when the flow of product stops, press the wash and pump keypa...
Page 61
57 model ph90 operating procedures 081210 step 3 open the draw valve on the freezer door. Drain all the rinse water from the door spout, close the draw valve, and press the wash keypad, cancelling the wash cycle. Step 4 repeat this procedure using clean, warm water, until the water being discharged ...
Page 62
58 model ph90 operating procedures step 1 remove the syrup lines from the syrup ports, and remove the restrictor cap from the bottom of the door spout. Step 2 remove the spinner blade from the bottom of the door spout by lifting up the plunger nut on the spinner coupling and pulling down the blade. ...
Page 63
59 model ph90 operating procedures 080221 remove the two small o--rings and one large o--ring from the drive shaft. Step 7 remove the front drip tray and splash shield. Remove the ladles from the two cold topping containers. Step 8 remove the long drip pan from the front panel, the two short drip pa...
Page 64
60 model ph90 operating procedures 080221 using small double end brush, brush clean the syrup line fittings. Step 6 prepare a sink with an approved 100 ppm sanitizing solution (example: kay--5 r or stera--sheen r ). Use warm water and follow the manufactur- er’s specifications. Repeat step 5 with th...
Page 65: Section 7
61 model ph90 important: operator checklist section 7 important: operator checklist during cleaning and sanitizing always follow local health codes. Cleaning and sanitizing schedules are governed by your state or local regulatory agencies and must be followed accordingly. The following check points ...
Page 66
62 model ph90 important: operator checklist 080221 winter storage if the place of business is to be closed during the winter months, it is important to protect the freezer by following certain precautions, particularly if the building is to be left unheated and subject to freezing conditions. Discon...
Page 67: Section 8
Section 8 troubleshooting guide troubleshooting guide model ph90 63 p roble m sh ak e si d e p roba ble c au se so ft se rv e s id e p roba ble c au se ei th er si d e p roba ble c au se remed y pa g e ref . 1. A ll four le d’ s ar e flas hing. A. T he fr eez er is loc ked. A. S ee sof tl oc k and h...
Page 68
Troubleshooting guide model ph90 64 p roble m sh ak e si d e p roba ble c au se so ft se rv e s id e p roba ble c au se ei th er si d e p roba ble c au se co rrect iv e a ct io n pa g e ref . 2. S of tloc k m es sage appear s on lcd. ( c ont ’d. ) e. T he agit at or is not ins talled. E. T he agit a...
Page 69
Troubleshooting guide model ph90 65 p roble m sh ak e si d e p roba ble c au se so ft se rv e s id e p roba ble c au se ei th er si d e p roba ble c au se co rrect iv e a ct io n pa g e ref . 4. No pr oduc ti s being dis pens ed. (c ont ’d. ) d. B eat er m ot or is out on re se t. D. Clear th e tone...
Page 70
Troubleshooting guide model ph90 66 p roble m sh ak e si d e p roba ble c au se so ft se rv e s id e p roba ble c au se ei th er si d e p roba ble c au se co rrect iv e a ct io n pa g e ref . 5. T he pr oduc ti s too th ick. A. Not enough sy rup -- 1 fl. Oz .( 30 m l.) in 5 sec onds . A. Calibr at e...
Page 71
Troubleshooting guide model ph90 67 p roble m sh ak e si d e p roba ble c au se so ft se rv e s id e p roba ble c au se ei th er si d e p roba ble c au se co rrect iv e a ct io n pa g e ref . 6. P roduc ti s too so ft. (c ont ’d. ) f. Inadequat e w at er supply on w at er cooled unit s. F. Chec k th...
Page 72
Troubleshooting guide model ph90 68 p roble m sh ak e si d e p roba ble c au se so ft se rv e s id e p roba ble c au se ei th er si d e p roba ble c au se co rrect iv e a ct io n pa g e ref . 11 . E xce ssi ve mi x leak age fr om th e bot to m of door spout . A. B ot to m o- -r ing on dr aw va lv e ...
Page 73
Troubleshooting guide model ph90 69 p roble m sh ak e si d e p roba ble c au se so ft se rv e s id e p roba ble c au se ei th er si d e p roba ble c au se co rrect iv e a ct io n pa g e ref . 13. T he dr iv e shaf ti s st uc k in the dr iv e coupling. A. M ix and lubr ic ant co llec ted in dr iv e c...
Page 74
Troubleshooting guide model ph90 70 p roble m sh ak e si d e p roba ble c au se so ft se rv e s id e p roba ble c au se ei th er si d e p roba ble c au se co rrect iv e a ct io n pa g e ref . 15. S pinner shaf twill not ro ta te to blend m ix and sy rup. A. F lex ible coupling is br ok en. A. Call s...
Page 75
Troubleshooting guide model ph90 71 p roble m sh ak e si d e p roba ble c au se so ft se rv e s id e p roba ble c au se ei th er si d e p roba ble c au se co rrect iv e a ct io n pa g e ref . 16. Lar ge pr es su re adjus tm ent s ar e nec es sa ry to re ce iv e 1 fl. Oz . (3 0m l.) in5 se conds .( c...
Page 76
Troubleshooting guide model ph90 72 p roble m sh ak e si d e p roba ble c au se so ft se rv e s id e p roba ble c au se ei th er si d e p roba ble c au se co rrect iv e a ct io n pa g e ref . 18. M ac hine will not ru n w hen in th e a u to m ode. (c ont ’d. ) c. Cir cu it br eak er o f f or blown f...
Page 77
Troubleshooting guide model ph90 73 p roble m sh ak e si d e p roba ble c au se so ft se rv e s id e p roba ble c au se ei th er si d e p roba ble c au se co rrect iv e a ct io n pa g e ref . 23. S yr up toppings ar e not hot . A. No wat er is in topping well. A. F ill to indic at ing m ar k. 44 b. ...
Page 78
Troubleshooting guide model ph90 74 p roble m sh ak e si d e p roba ble c au se so ft se rv e s id e p roba ble c au se ei th er si d e p roba ble c au se co rrect iv e a ct io n pa g e ref . 27. P um p par ts dif fic ult to asse mb le . A. S hak e and so ft se rv e pum p co m ponent s ar e in te rm...
Page 79: Section 9
75 model ph90 parts replacement schedule section 9 parts replacement schedule part description every 3 months every 6 months annually scraper blade--shake x scraper blade--soft serve x drive shaft seal x freezer door o--ring--shake x freezer door gasket--soft serve x front bearing x beater front sho...
Page 80: Section 10
Section 10 parts list + available separately 76 parts list model ph90 descri pti o n part number qty . W arr. Class remarks parts upda te accumulator a. -a ir *5472* prtl x46916 1 103 fi tti ng a. -a ir accumulator x48548 1 103 j5010000/ up 90 +tube- vi nyl 1 /8 id x 1 /1 6 w all 020938- 6 1 000 bul...
Page 81
77 + available separately model ph90 parts list descri pti o n parts upda te remarks w arr. Class qty . Part number block- termi n al- p lug 8 p .2 s ip 040322- 004 2 103 blow er a. -h ig h o utput x53478- 27 1 103 j9110000/ up 148 capaci t or- run- 10 uf/ 370v 033047 1 103 148 cli p -s creen- b low...
Page 82
+ available separately 78 parts list model ph90 descri pti o n parts upda te remarks w arr. Class qty . Part number cable- ri bbon- 14c- 14” l s ip /s ip r 040040- 015 1 103 j9- u c t o l c d cable- ri bbon- 20c- 78” r d il /d il 040040- 032 1 103 j2- u c t o j 12- ib shake cable- ri bbon- 20c- 9 ”d...
Page 83
79 + available separately model ph90 parts list descri pti o n parts upda te remarks w arr. Class qty . Part number +grommet- compressor m ounti n g 037428 4 000 j4047459/ pri o r 80 +sleeve- comp. M ounti n g 037429 4 000 j4047459/ pri o r 80 com p ressor a h7513z- a h245rt - shake 047520- 1 512 j4...
Page 84
+ available separately 80 parts list model ph90 descri pti o n parts upda te remarks w arr. Class qty . Part number decal- dai l y c leani n g- ht combo 045272 1 000 decal- dec- taylor- p h90 052282 1 000 j8070000/ up (o n p o s it io n - ri g h t s id e) 132 decal- dec- taylor- p h90 046179 1 000 p...
Page 85
81 + available separately model ph90 parts list descri pti o n parts upda te remarks w arr. Class qty . Part number + p in a .-p iv o t x22820 1 103 +o -r in g -5/ 16 o d x .070w 016272 1 000 +valve a. -draw *self c leani n g* x33582 1 103 +o -r in g -7/ 8 o d x .103w 014402 3 000 do o r a. -syrup c...
Page 86
+ available separately 82 parts list model ph90 descri pti o n parts upda te remarks w arr. Class qty . Part number hi nge a .- motor m ount left x25736 1 103 hi ng e a .- pi n *8634* ri g h t x45739 2 103 hi ng e a .- pi n *8634* left x45743 2 103 holder a. -sensor a djustable x51464 1 103 j7120000...
Page 87
83 + available separately model ph90 parts list descri pti o n parts upda te remarks w arr. Class qty . Part number ki t a .- door 1 spout fi eld r eplacement x51531- 1 1 103 m u st use o n uni ts befo r e s /n j5080000 to replace x 45156- ser door assy. 96 beari n g- front 050348 1 000 so ft serve ...
Page 88
+ available separately 84 parts list model ph90 descri pti o n parts upda te remarks w arr. Class qty . Part number o -ri ng -3 /4 o d x .103w 015835 2 000 mi x inlet tube o -ri ng -5 /1 6 o d x .070w 016272 2 000 pi vot p in o- ri ng- 6 in odx5 3/ 4 idx 1/ 8 033493 1 000 shake door o -ri ng -7 /8 o...
Page 89
85 + available separately model ph90 parts list descri pti o n parts upda te remarks w arr. Class qty . Part number louver- s id e 028288 1 103 left si de lubri c ant- taylor hi perf- 4 o z 048232 1 000 man- oper ph90 047772- m 1 000 m a ni fo ld a. -r eg ulato r *8634* x46983 1 103 decal- flavor c ...
Page 90
+ available separately 86 parts list model ph90 descri pti o n parts upda te remarks w arr. Class qty . Part number coupli ng- m otor- f lexi ble 047936 2 103 86 gear- o nly 049247- 34 2 103 (5 0 & 60hz) 93 mot o r- onl y 049246- 34 2 103 (5 0 & 60hz) 93 seal- m otor reducer- in put s haft 048836 2 ...
Page 91
87 + available separately model ph90 parts list descri pti o n parts upda te remarks w arr. Class qty . Part number panel- r ear *8634 ai r* 044054 1 103 j4070000/ pri o r (see ki t x 48208- ser) 84 panel- u pper si de 051631 1 103 left si de - j 7120000/ up 125 panel- u pper si de 024426 1 103 left...
Page 92
+ available separately 88 parts list model ph90 descri pti o n parts upda te remarks w arr. Class qty . Part number probe- thermi stor- barrel- 2% tol 038061- blk 2 103 barrel probe- thermi stor- h opper- 2 % t ol 039470- blk 3 103 hopper and h eater pulley- ag t m tr- 1 .910pdx3/ 8bo r e 042063 1 1...
Page 93
89 + available separately model ph90 parts list 051103 descri pti o n parts upda te remarks w arr. Class qty . Part number o -ri ng -2 -1 /8 o d x .139w 020051 3 000 o -ri ng -3 /4 o d x .103w 015835 1 000 pi n a .- coax pump *h t* ss* x36950 1 103 +pi n -c otter- hai r pi n- 1/ 8di a 044731 1 103 p...
Page 94
+ available separately 90 parts list model ph90 051103 descri pti o n parts upda te remarks w arr. Class qty . Part number + m otor onl y 041785- 1 1 112 + p ump o nly 041785- 2 1 112 + m agnet o nly 041785- 3 1 103 +boot- g lycol p ump 042131 1 000 relay- 3 p o l e- 20a- 208/ 240 50/ 60 012725- 2 1...
Page 95
91 + available separately model ph90 parts list descri pti o n parts upda te remarks w arr. Class qty . Part number sleeve a. -m ix pump *h t* mcd x44761 2 103 +nut- p um p s leeve *8751* ht* 036933 2 103 spi nner *8663* 034054 1 103 +seal- spi nner s haft 036053 1 000 socket- q .D . L iq .- 90deg- ...
Page 96
+ available separately 92 parts list model ph90 descri pti o n parts upda te remarks w arr. Class qty . Part number sw it ch- toggle- spst 012626 2 103 syrup heater - 042782 pri o r t o j 8070000 syrup rai l assy spare parts heater- s tri p -175w -240v 042782 2 103 label- t emperature adjustment 030...
Page 97
93 + available separately model ph90 parts list descri pti o n parts upda te remarks w arr. Class qty . Part number tube a. -h eat t. Pump feed x44666 1 103 soft serve tube a. -h eat t. Pump feed x44615 1 103 shake tube- .170 id x .250 od - syrup valve 075885- 96 var 000 bulk under r 40302 (cut to l...
Page 98
+ available separately 94 parts list model ph90 descri pti o n parts upda te remarks w arr. Class qty . Part number water c ooled blo w er- 100cfm 012796- 1 103 condenser- w /c -c oaxi al 047540 2 103 j4047460/ up hp62 80 condenser- w /c coaxi al 031651 2 103 j4047459/ pri o r 80 elbow -3/ 8mp x 1 /...
Page 99
95 + available separately model ph90 parts list descri pti o n parts upda te remarks w arr. Class qty . Part number starter- 3 p hase 1. 4 t o 2 .3 a 041950- 33g 1 103 shake 50hz 3 phase starter- 3 p hase 2. 0 t o 3 .3 a 041950- 33h 1 103 soft serve 50hz 3 phase.
Page 100
047984--33 rev. 2/03.
Page 101
047984--33 inset rev. 2/03.
Page 102
047984--62 rev. 2/03.