Summary of QS10
Page 1
Models qs10/qs22 auto lift grills operating instructions 072970-m 71/08.
Page 2
Complete this page for quick reference when service is required: taylor distributor: address: phone: fax: e-mail: service: parts: date of installation: information found on the data label: model number: serial number: electrical specs: voltage cycle phase maximum fuse size: a minimum wire ampacity: ...
Page 3: Table Of Contents
Models qs10 & qs22 table of contents table of contents section 1 to the installer 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air clearance 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 4
Table of contents models qs10 & qs22 table of contents - page 2 section 7 troubleshooting guide 24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section 8 warranty explanation 26 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parts 26 . . . . . ...
Page 5: Section 1
1 models qs10 & qs22 to the installer section 1 to the installer these machines are designed for indoor use only. Do not install the machine in an area where a water jet could be used to clean or rinse the machine. Failure to follow this instruction may result in serious electrical shock. Air cleara...
Page 6
2 models qs10 & qs22 to the installer installation of cable kit kit a.-3 ft. Restrain cable (part no. 074948) must be installed to limit the movement of the grill. This is necessary in order to protect the electrical conduit from stress. The cable is made of flexible conduit. To install the kit, loo...
Page 7: Section 2
3 models qs10 & qs22 to the operator section 2 to the operator the grill you have purchased has been carefully engineered and manufactured to provide dependable operation. The qs series grills are designed to deliver “cook-to-order” menu items. The two-sided cooking method increases speed of service...
Page 8: Section 3
4 models qs10 & qs22 safety section 3 safety we at taylor company are deeply concerned about the safety of the operator when he or she comes in contact with the grill and its parts. Taylor has gone to extreme efforts to design and manufacture built-in safety features to protect both you and the serv...
Page 9: Section 4
5 models qs10 & qs22 operator parts identification section 4 operator parts identification qs10 figure 2 item description part no. 1 cover-pullout grease can 072299 2 tray a.-grease x71906 item description part no. 3 standoff-rear 079288 4 standoff-front 079289 5 collar-holding 019481.
Page 10
6 models qs10 & qs22 operator parts identification qs22 figure 3 item description part no. 1 cover-pullout grease can 072299 2 tray a.-grease x71906 item description part no. 3 standoff-rear 079288 4 standoff-front 079289 5 collar-holding 019481.
Page 11
7 models qs10 & qs22 operator parts identification accessories figure 4 item description part no. 1 sheet-release qs24 auto w/loop 072609 2 retainer-release qs 072607 3 clip-release material 072673 item description part no. 4 bar-release sheet qs 072608 5 scraper-teflon wiper 075887.
Page 12: Section 5
8 models qs10 & qs22 important: to the operator section 5 important: to the operator qs10 figure 5 item description 1 gap handle 2 gap indicator 3 power switch 4 timer button - green item description 5 raise button - red 6 keys 7 indicator lights 8 led display.
Page 13
9 models qs10 & qs22 important: to the operator qs22 figure 6 item description 1 gap handle-left side 2 gap handle-right side 3 gap indicator-left side 4 gap indicator-right side 5 power switch-left side 6 power switch-right side 7 timer button-left side 8 timer button-right side item description 9 ...
Page 14
10 models qs10 & qs22 important: to the operator power switch (rocker) when placed in the on position, the power switch allows control panel operation. The power switch is located on the front panel. Indicator light the lights on the front panel indicate when the heaters are operating. Heating zones...
Page 15
11 models qs10 & qs22 important: to the operator operating screen and controls the version screen is viewed when a grill is powered for normal operation. It indicates the version of software the microprocessor is using. Ver 1.01b note: if the grill is not equipped with the upper cook surface option,...
Page 16
12 models qs10 & qs22 important: to the operator for example, item one has been programmed to cook for 135 seconds. The operator wishes to add salt in the middle of the cook cycle. Timer two should then be programmed for 15 seconds. Once the cook cycle begins, a tone will sound 15 seconds after the ...
Page 17
13 models qs10 & qs22 important: to the operator maintenance menu the maintenance menu provides five screens to allow managers and service technicians to monitor grill performance. To enter the maintenance menu while any item is displayed, press and hold the menu key for approximately 5 seconds and ...
Page 18
14 models qs10 & qs22 important: to the operator note: the calibrat screen is the base maintenance screen. All other maintenance functions are accessible through the calibrat screen. Step 1 press the menu key to display the current temperature scale: scale f or c step 2 fahrenheit is the desired tem...
Page 19
15 models qs10 & qs22 important: to the operator step 11 press the up arrow to display “language”, and press the menu key to display “english”. Press the menu key to return to the “language” display. Step 12 press the up arrow to display “monitor”. Press the menu key to display “uf xxx f” to monitor...
Page 20
16 models qs10 & qs22 important: to the operator maintenance menu flowchart figure 8.
Page 21: Section 6
17 models qs10 & qs22 operating procedures section 6 operating procedures the model qs10 has one 12” (305 mm) lower cook surface and one 11” (279 mm) upper platen. The model qs22 has two 12” (305 mm) lower cook surfaces and two 11” (279 mm) upper platens. The two-sided cooking concept ensures quick,...
Page 22
18 models qs10 & qs22 operating procedures step 4 place the release material clips over the release material sheet, pressing them into place over the release material bar at the top of the platen. Figure 12 step 5 check the alignment and tightness of the release material against the upper platen. St...
Page 23
19 models qs10 & qs22 operating procedures cooking procedures step 1 make sure that the release material sheets are installed. Step 2 place the power switch(es) in the on position. This illuminates the switch(es). The screen will scroll through information messages and then advance to the first cook...
Page 24
20 models qs10 & qs22 operating procedures step 6 while the upper cook surface is in the raised position, place the product on the lower cook surface. Lower the upper cook surface. Caution: the grill is hot. To prevent personal injury, always use the handle to lower the upper cook surface. Step 7 if...
Page 25
21 models qs10 & qs22 operating procedures step 3 using the rubber wiper squeegee, push the grease to the rear of the lower surface into the grease trough. Do not use the grill scraper for this step. Step 4 when necessary, use a grill cloth to clean the back splash shield and the bullnose areas. Ste...
Page 26
22 models qs10 & qs22 operating procedures step 5 carefully remove the grease tray partition. Take it to the sink for cleaning. Figure 21 note: for installation of the grease tray partition, carefully reverse the above steps. Closing procedures step 1 raise the upper cook surface to the raised posit...
Page 27
23 models qs10 & qs22 operating procedures step 10 starting at the front of the upper cook surface and the rear of the lower cook surface, rinse both surfaces with a mist of water from a spray bottle. Warning! Use care not to allow water or cleaner/degreaser on any part of the grill other than the c...
Page 28: Section 7
24 models qs10 & qs22 troubleshooting guide section 7 troubleshooting guide problem probable cause remedy 1. Grill will not heat. A. Power cord is not connected. A. Check the power connection. B. Circuit breaker is tripped. B. Reset the circuit breaker. C. Power switch is in the off position. C. Pla...
Page 29
25 models qs10 & qs22 troubleshooting guide problem probable cause remedy 6. Product is under-cooked, overcooked, or cooking unevenly. A. Release material sheet is worn. A. Replace release material sheet. B. Incorrect cooking time. B. Adjust the cook time accordingly. C. Incorrect temperature settin...
Page 30: Section 8
26 models qs10 & qs22 warranty explanation section 8 warranty explanation parts class 103 parts the warranty for new equipment is one year, with a replacement parts warranty of three months. Class 000 parts wear items - no warranty. Class 212 parts the warranty for new equipment parts is two years, ...
Page 31
Qs10 & qs22 072396-23 7/08.