- DL manuals
- Taylor
- Grill
- QS11
- Operating Instructions Manual
Taylor QS11 Operating Instructions Manual
Summary of QS11
Page 1
Models qs11/23 modular grills operating instructions 074606-m 5/24/04.
Page 2
Complete this page for quick reference when service is required: taylor distributor: address: phone: service: parts: date of installation: information found on the data label: model number: serial number: electrical specs: voltage cycle phase maximum fuse size: a minimum wire ampacity: a e may, 2004...
Page 3: Table Of Contents
Table of contents models qs11 & qs23 table of contents section 1 to the installer 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air clearance 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 4
Models qs11 & qs23 table of contents table of contents -- page 2 cleaning between product runs 25 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cleaning the grease tray partition 26 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Closing ...
Page 5: Section 1
1 models qs11 & qs23 to the installer 071102 section 1 to the installer this machine is designed for indoor use only. Do not install the machine in an area where a water jet could be used to clean or rinse the machine. Failure to follow this instruction may result in serious electrical shock. Air cl...
Page 6
2 to the installer models qs11 & qs23 060504 installation of cable kit kit a.-3 ft. Restrain cable (part no. 074948) must be installed to limit the movement of the grill. This is necessary in order to protect the electrical conduit from stress. The cable is made of flexible conduit. To install the k...
Page 7
3 models qs11 & qs23 to the installer leveling procedures figure 2 step 1 the leveling adjustment needs to be performed when the grill is properly gapped and at operating temperature. Level the grill without the release material sheets in place. Step 2 to allow adjustment of the gap pins, loosen the...
Page 8
4 to the installer models qs11 & qs23 step 4 for each cook surface requiring adjustment, place the four gap blocks on the cook surface, approximately 2” (51 mm) in from each corner. (figure 5) figure 5 step 5 lower the cook surface assembly. Loosen and slowly move the t‐handle to the left until the ...
Page 9
5 models qs11 & qs23 to the installer 090401 step 8 lower the upper cook surface into the cook position. 14115 figure 9 step 9 wearing proper protection, attempt to rock the cook surface assembly. Apply slight pressure on the locating pins at opposite corners to each other as shown in figure 10. Fig...
Page 10: Section 2
6 to the operator models qs11 & qs23 050831 section 2 to the operator the grill you have purchased has been carefully engineered and manufactured to provide dependable operation. The qs series grills are designed to deliver “cook‐to‐order” menu items. The two‐sided cooking method increases speed of ...
Page 11: Section 3
7 models qs11 & qs23 safety 040408 section 3 safety we at taylor company are deeply concerned about the safety of the operator when he or she comes in contact with the grill and its parts. Taylor has gone to extreme efforts to design and manufacture built‐in safety features to protect both you and t...
Page 12
8 safety models qs11 & qs23 040210 this grill must be placed on a level surface. Failure to comply may result in personal injury or equipment damage. Caution: do not attempt to use the grill during a power outage. Grills require electrical power for operation. In the event of a prolonged power outag...
Page 13: Section 4
9 models qs11 & qs23 operator parts identification 071102 section 4 operator parts identification qs11 2 1 3 4 figure 13 item description part no. 1 cover-top 079969 2 tray a.-grease x79940-ser item description part no. 3 standoff-rear 079288 4 standoff-front 079289.
Page 14
10 operator parts identification models qs11 & qs23 071102 qs23 2 1 3 4 figure 14 item description part no. 1 cover-top 079969 2 tray a.-grease x79940-ser item description part no. 3 standoff-rear 079288 4 standoff-front 079289.
Page 15
11 models qs11 & qs23 operator parts identification 071102 qs11 accessories 5 3 4 8 13 14 19 18 9 7 20 15 16 17 11 10 6 12 sizzle 1 2 figure 15.
Page 16
12 operator parts identification models qs11 & qs23 071102 qs11 accessories - parts identification item description part no. 1 scraper a.-groove x79246 2 scraper a.-groove x79668 3 scraper-teflon wiper 075887 items 4-12 are included in x70300 kit 4 scraper-trough 079726 5 bar-release sheet 079930 6 ...
Page 17
13 models qs11 & qs23 operator parts identification 071102 qs23 accessories 5 3 4 8 13 14 19 18 9 7 20 15 16 17 11 10 6 12 sizzle 1 2 figure 16.
Page 18
14 operator parts identification models qs11 & qs23 qs23 accessories - parts identification item description part no. 1 scraper a.-groove x79246 2 scraper a.-groove x79668 items 3-12 are included in x70300-2 kit 3 scraper-teflon wiper 75887 4 scraper-trough 079726 5 bar-release sheet 079930 6 sheet-...
Page 19: Section 5
15 models qs11 & qs23 important: to the operator section 5 important: to the operator item description 1 power switch 2 keys 3 led display 4 indicator lights 5 timer button power switch (rocker) when placed in the on position, the power switch allows control panel operation. The power switch is loca...
Page 20
16 important: to the operator models qs11 & qs23 temperature controls the model qs11 is equipped with one temperature control and the model qs23 is equipped with two individual temperature controls. They control both the upper and the lower temperatures. The lower cook surface temperatures can be se...
Page 21
17 models qs11 & qs23 important: to the operator 080926 cook temperatures step 1 to set cook temperatures, press the up or down arrow to select the item to be changed. Press and hold the temperature key for five seconds. After releasing the key, the message “su1” and the current set temperature will...
Page 22
18 important: to the operator models qs11 & qs23 fault screen if the grill experiences a system failure, a fault message will appear on the display, and a tone will sound. Flt htum an example of the fault screen is illustrated in the previous figure. The screen appears when the controller has detect...
Page 23
19 models qs11 & qs23 important: to the operator note: calibration is allowed only when the item 1 temperatures are within 50 _f (28_c) of the set point. (calibrate without the release material sheets in place.) step 2 place the pyrometer disc on the upper front heating element of the grill. The sen...
Page 24
20 important: to the operator models qs11 & qs23 step 6 press the menu key again, and the message “itm1” will appear on the display. The letter “i” will be flashing above the cursor. Itm1 step 7 using the up and down arrow keys, enter the desired letter (a ‐ z) or number (0 ‐ 9) ( - _ ). Once the ch...
Page 25
21 models qs11 & qs23 important: to the operator maintenance menu flowchart.
Page 26: Section 6
22 operating procedures models qs11 & qs23 section 6 operating procedures the model qs11 has one, 12” (305 mm) lower cook surface and the option of an 11” (289 mm) upper cook surface. The model qs23 has two 12” (305 mm) lower cook surfaces and the option of one 11” (279 mm) upper cook surface or two...
Page 27
23 models qs11 & qs23 operating procedures step 4 raise the upper cook surface and assure that the release material sheet fits evenly from front to back, and snugly on the upper cook surface. (rotate the release material sheet on an every other day basis.) note: replace release material sheets if sm...
Page 28
24 operating procedures models qs11 & qs23 cooking procedures step 1 make sure that the release material sheets are installed. Step 2 place the power switch(es) in the on position. The screen will scroll through information messages and then advance to the first cook screen. Figure 22 note: if there...
Page 29
25 models qs11 & qs23 operating procedures caution: the grill is hot. To prevent personal injury, always use the handle to lower the upper cook surface. Step 7 if the timer is programmed, press the large red timer button. A tone will sound for two seconds, alerting the operator that the cook cycle h...
Page 30
26 operating procedures models qs11 & qs23 090401 step 3 using the rubber wiper squeegee, push the grease to the rear of the lower surface into the grease trough. Do not use the grill scraper for this step. Step 4 when necessary, use a grill cloth to clean the back splash shield and the bullnose are...
Page 31
27 models qs11 & qs23 operating procedures closing procedures step 1 raise the upper cook surface to the “raised” position. Step 2 turn the power switches to the off position. Figure 32 step 3 wipe the release material sheet thoroughly while still attached to the upper cook surface, using the rubber...
Page 32
28 operating procedures models qs11 & qs23 090401 step 13 clean lower grill by pouring warm water carefully on the surface while brushing with sturdy brush. Caution: wear rubber gloves to avoid hot steam. Step 14 continue to add water and brush the surface until the grill is cool enough to squeegee ...
Page 33: Section 7
29 models qs11 & qs23 troubleshooting guide section 7 troubleshooting guide problem probable cause remedy 1. Grill will not heat. A. Power cord is not connected. A. Check the power connection. B. Circuit breaker is tripped. B. Reset the circuit breaker. C. Power switch is in the off position. C. Pla...
Page 34
30 troubleshooting guide models qs11 & qs23 problem probable cause remedy 6. Product is under‐cooked, overcooked, or cooking unevenly. A. Release material sheet is worn. A. Replace release material sheet. B. Incorrect cooking time. B. Adjust the cook time accordingly. C. Incorrect temperature settin...
Page 35: Section 8
31 models qs11 & qs23 warranty explanation section 8 warranty explanation parts class 103 parts the warranty for new equipment is one year, with a replacement parts warranty of three months. Class 000 parts wear items - no warranty. Class 212 parts the warranty for new equipment parts is two years, ...
Page 36: Section 9
Section 9 parts list + available separately 32 parts list models qs11 & 23 051108 de s cri p t io n p art num be r qs 1 1 qty . Qs 2 3 qty . W arr. Cl as s re m arks part s up da t e bar- adj usti ng gap *qs24* 078779 1 2 103 upper platen bar- g ap- adj sli de mtg *qs24* 078783 2 4 103 upper platen ...
Page 37
33 + available separately models qs11 & 23 parts list 061004 de s cri p t io n part s up da t e re m arks w arr. Cl as s qs 2 3 qty . Qs 1 1 qty . P art num be r co ver- t o p q s 12/ q s 24 079969 1 1 103 cover for g rease tray decal- termi n al block *qs12* 079533 1 2 000 decal- termi n al block *...
Page 38
+ available separately 34 parts list models qs11 & 23 051108 de s cri p t io n part s up da t e re m arks w arr. Cl as s qs 2 3 qty . Qs 1 1 qty . P art num be r w asher- 3 /8 shakeproof- extern 001087 2 000 ki t a. -rear cvr stop bar- q s12 x79689- ser 1 103 bar- r ear- c over support 079855 2 103 ...
Page 39
35 + available separately models qs11 & 23 parts list 051108 de s cri p t io n part s up da t e re m arks w arr. Cl as s qs 2 3 qty . Qs 1 1 qty . P art num be r parti ti on a. -g rease tray *q s24 x79944 1 1 103 pcb a. -control *qs12/ 24* gri l x53512- ser 1 2 212 chi p- softw are *qs24b* c trl x40...
Page 40
+ available separately 36 parts list models qs11 & 23 051108 de s cri p t io n part s up da t e re m arks w arr. Cl as s qs 2 3 qty . Qs 1 1 qty . P art num be r retai n er- beari n g *qs24* 079191 2 2 103 rod- cyl m tg *q s24* 079195 1 1 103 rod- li nkage 3 /4 di a *qs24* 079216 1 1 103 rod- platen...
Page 41
37 + available separately models qs11 & 23 parts list 051108 de s cri p t io n part s up da t e re m arks w arr. Cl as s qs 2 3 qty . Qs 1 1 qty . P art num be r spri n g -. 438 o d x .046 x 1 .7 5 079704 6 6 103 standoff- front *qs12* 079289 4 4 103 standoff- rear *q s12* 079288 2 2 103 sw it ch- r...
Page 42
Qs11/qs23 074626--23 rev. 4/09.