- DL manuals
- Taylor
- Grill
- QS12
- Operating Instructions Manual
Taylor QS12 Operating Instructions Manual
Summary of QS12
Page 1
Models qs12 & qs24 modular grills operating instructions 050559--m 2/20/01.
Page 2
Complete this page for quick reference when service is required: taylor distributor: address: phone: service: parts: date of installation: information found on data plate: model number: serial number: electrical specs: voltage cycle phase maximum fuse size: amps minimum wire ampacity: amps part numb...
Page 3: Table Of Contents
Table of contents models qs12 & qs24 table of contents section 1 to the installer 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air clearance 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 4
Models qs12 & qs24 table of contents table of contents -- page 2 section 7 troubleshooting guide 29 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section 8 warranty explanation 31 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parts 31 . . . . ....
Page 5: Section 1
1 models qs12 & qs24 to the installer 050831 section 1 to the installer this machine is designed for indoor use only. Do not install the machine in an area where a water jet could be used to clean or rinse the machine. Failure to follow this instruction may result in serious electrical shock. Air cl...
Page 6
2 to the installer models qs12 & qs24 ventilation and clearance to ensure proper operation of this appliance it must be installed so that the products of combustion are efficiently removed. Do not store anything on top of the grill. Most service can be performed from the front of the grill. When ins...
Page 7
3 models qs12 & qs24 to the installer step 3 raise or lower both gap pins on the front gap slide until they are flush with the top edge of the gap slide. Repeat this step for the rear gap slide. Slide the gap slide to the right. Figure 4 step 4 for each cook surface requiring adjustment, place 4 gap...
Page 8
4 to the installer models qs12 & qs24 090401 step 8 lower the upper cook surface into the cook position. Figure 9 step 9 wearing proper protection, attempt to rock the cook surface assembly. Apply pressure on the locating pins at opposite corners to each other as shown in figure 10. Figure 10 step 1...
Page 9: Section 2
5 models qs12 & qs24 to the operator 050831 section 2 to the operator the grill you have purchased has been carefully engineered and manufactured to provide dependable operation. This grill is designed to deliver “cook-to-order” menu items. The two-sided cooking method increases speed of service and...
Page 10: Section 3
6 safety models qs12 & qs24 070116 section 3 safety we at taylor are deeply concerned about the safety of the operator when he or she comes in contact with the grill and its parts. Taylor has gone to extreme efforts to design and manufacture built-in safety features to protect both you and the servi...
Page 11
7 models qs12 & qs24 safety do not slide the grill with the legs attached. Failure to follow this instruction may damage the grill. Do not obstruct air intake and discharge openings: 4” (102 mm) minimum air space on the bottom and 3” (76 mm) at the rear of the unit. Failure to comply will affect gri...
Page 12: Section 4
8 operator parts identification models qs12 & qs24 071102 section 4 operator parts identification qs12 on off 1 2 3 4 figure 12 item description part no. 1 standoff-rear 079288 2 standoff-front 079289 3 tray a. - grease x79940-ser item description part no. 4 cover-top 079969 * cleaner-sizzle 079896 ...
Page 13
9 models qs12 & qs24 operator parts identification 071102 qs24 2 1 on off on off 3 4 figure 13 item description part no. 1 tray a.--grease x79940--ser 2 cover--top 079969 3 standoff--front 079289 item description part no. 4 standoff--rear 079288 * cleaner--sizzle 079896 *not shown.
Page 14
10 operator parts identification models qs12 & qs24 071102 qs12 accessories 5 3 4 8 13 14 19 18 9 7 20 15 16 17 11 10 6 12 sizzle 1 2 figure 14.
Page 15
11 models qs12 & qs24 operator parts identification qs12 accessories -- parts identification item description part no. 1 scraper a.-groove x79246 2 scraper a.-groove x79668 3 scraper-teflon wiper 075887 4 scraper-trough 079726 5 bar-release sheet 079930 6 sheet-seamed release 078804 7 spring-.438 od...
Page 16
12 operator parts identification models qs12 & qs24 071102 qs24 accessories 5 3 4 8 14 9 7 15 12 13 11 10 6 sizzle 1 2 figure 15.
Page 17
13 models qs12 & qs24 operator parts identification qs24 accessories -- parts identification item description part no. 1 scraper a.-groove x79246 2 scraper a.-groove x79668 3 scraper-teflon wiper 75887 4 scraper-trough 079726 5 bar-release sheet 079930 6 sheet-seamed release 078804 7 spring-.438 od ...
Page 18: Section 5
14 important: to the operator models qs12 & qs24 071102 section 5 important: to the operator menu uf time temp up down exit um ur lr lm lf m a n u f a c t u r e d b y t h e t a y l o r c o m p a n y r o c k t o n , i l l i n o i s u . S . A . 4 3 2 1 i 0 5 item description 1 power switch 2 keypads 3...
Page 19
15 models qs12 & qs24 important: to the operator temperature controls the model qs12 is equipped with one temperature control and the model qs24 is equipped with two individual temperature controls. They control both the upper and the lower temperatures. The lower cook surface temperatures can be se...
Page 20
16 important: to the operator models qs12 & qs24 080429 cook temperatures step 1 to set cook temperatures, press the up or down arrow to select the item to be changed. Press and hold the temperature key for five seconds. After releasing the key, the message “su1” and the current set temperature will...
Page 21
17 models qs12 & qs24 important: to the operator fault screen if the grill experiences a system failure, a fault message will appear on the display, and a tone will sound. Flt htum an example of the fault screen is illustrated in the previous figure. The screen appears when the controller has detect...
Page 22
18 important: to the operator models qs12 & qs24 note: a calibrated pyrometer must be used for calibration. Note: calibration is allowed only when the item1 temperatures are within 50_ f (28_ c) of the set point. Step 2 place the pyrometer disc on the upper front heating element of the grill. Using ...
Page 23
19 models qs12 & qs24 important: to the operator step 6 press the menu key again, and the message “itm1” will appear on the display. The letter “i” will be flashing above the cursor. Itm1 step 7 using the up and down arrow keys, enter the desired letter (a - z) or number (0 - 9) ( -- _ ). Once the c...
Page 24
20 important: to the operator models qs12 & qs24 maintenance menu flowchart.
Page 25: Section 6
21 models qs12 & qs24 operating procedures section 6 operating procedures the model qs12 has one, 12” (305 mm) lower cook surface and the option of an 11” (279 mm) upper cook surface. The model qs24 has two, 12” (305 mm) lower cook surfaces and the option of one 11” (279 mm) upper cook surface or tw...
Page 26
22 operating procedures models qs12 & qs24 step 4 raise the upper cook surface and assure that the release material sheet fits evenly and snugly on the upper cook surface. Rotate the release material sheet on an every other day basis. Note: it is not necessary to replace the release material sheet i...
Page 27
23 models qs12 & qs24 operating procedures caution: release material sheets must be replaced if: s release material is torn. S release material substance is worn from the release material sheet. S product sticks to the release material. Cooking procedures step 1 make sure the release material is ins...
Page 28
24 operating procedures models qs12 & qs24 071102 caution: the grill is hot. To prevent personal injury, always use the handle to lower the upper cook surface. Step 7 if the timer is programmed, press the large red timer button. A tone will sound for two seconds, alerting the operator that the cook ...
Page 29
25 models qs12 & qs24 operating procedures 090401 step 3 using the rubber wiper squeegee, push the grease to the rear of the lower surface into the grease trough. Do not use the grill scraper for this step. Step 4 when necessary, use a grill cloth to clean the back splash shield and the bullnose are...
Page 30
26 operating procedures models qs12 & qs24 closing procedures step 1 raise the upper cook surface to the “raised” position. Step 2 turn the power switches to the off position. Figure 31 step 3 wipe the release material sheet thoroughly while still attached to the upper cook surface, using the rubber...
Page 31
27 models qs12 & qs24 operating procedures important: do not use a jet of water to clean or rinse the grill. Step 12 use the rubber wiper squeegee to remove excess liquid from the upper and lower surfaces. Important! Do not scrape the upper surface with metal utensils. It is aluminum and will scratc...
Page 32
28 operating procedures models qs12 & qs24 090401 weekly cleaning procedures step 1 loosen, but do not remove the four locating pins that attach both sets of gap slide retainers. One set is located at the front and one set is located at the rear of the upper platen. Step 2 lift the upper platen to t...
Page 33: Section 7
29 models qs12 & qs24 troubleshooting guide section 7 troubleshooting guide problem probable cause remedy 1. Grill will not heat. A. Power cord is not connected. A. Check power connection. B. Circuit breaker is tripped. B. Reset the circuit breaker. C. Power switch is in the off position. C. Place t...
Page 34
30 troubleshooting guide models qs12 & qs24 problem probable cause remedy 6. Product is under-cooked, overcooked, or cooking unevenly. A. Release material sheet is worn. A. Replace the release material sheet. B. Incorrect cooking time. B. Adjust cook time accordingly. C. Incorrect temperature settin...
Page 35: Section 8
31 models qs12 & qs24 warranty explanation section 8 warranty explanation parts class 103 parts the warranty for new equipment is one year, with a replacement parts warranty of three months. Class 000 parts wear items -- no warranty. Class 212 parts the warranty for new equipment parts is two years,...
Page 36: Section 9
Section 9 parts list + available separately 32 parts list models qs12 & qs24 de s cri p t io n part num be r qs 12 qty . Qs 24 qty . W arr. Cl as s re m arks part s up da t e bar --release sheet *q s24* 079930 2 2 103 137 block --g age p la ten k it 078095 4 4 103 block --t ermi nal --5 p s crew w /...
Page 37
33 + available separately models qs12 & qs24 parts list de s cri p t io n part s up da t e re m arks w arr. Cl as s qs 24 qty . Qs 12 qty . Part num be r bum per --. 500 di a x .090 thk 079499 1 2 000 decal --key pa d *qs24* x74320 --ser 1 2 000 bum per --. 500 di a x .090 thk 079499 1 2 000 fi lt e...
Page 38
+ available separately 34 parts list models qs12 & qs24 de s cri p t io n part s up da t e re m arks w arr. Cl as s qs 24 qty . Qs 12 qty . Part num be r gasket --access cover 074059 1 000 j9054573/ up 143 harness --control to r emote q s24 078618 1 2 103 control b oard to remote key pa d box harnes...
Page 39
35 + available separately models qs12 & qs24 parts list de s cri p t io n part s up da t e re m arks w arr. Cl as s qs 24 qty . Qs 12 qty . Part num be r pa n e l a .-- s id e le f t none not av a il able f or replacement -- sealed pa n e l a .-- s id e r ig h t none uni t to p revent g rease mi gra...
Page 40
+ available separately 36 parts list models qs12 & qs24 de s cri p t io n part s up da t e re m arks w arr. Cl as s qs 24 qty . Qs 12 qty . Part num be r rod --p la ten li n kage m id *q s24 079194 1 1 103 ro d --p la ten li n kag e m id *q s24* 078549 1 1 103 rod --p la ten li n kage u pper *q s24 ...
Page 41
37 + available separately models qs12 & qs24 parts list de s cri p t io n part s up da t e re m arks w arr. Cl as s qs 24 qty . Qs 12 qty . Part num be r w iper --si de left *q s24* 079437 1 1 103 w iper --si de ri ght *qs24* 079438 1 1 103 wi per --front *qs2 4* 079439 1 1 103 w iper --rear *q s24*...
Page 42
+ available separately 38 parts list models qs12 & qs24 de s cri p t io n part s up da t e re m arks w arr. Cl as s qs 24 qty . Qs 12 qty . Part num be r di agram --w ir in g (new ) 074063 --75 1 1 000 j9054573/ up 143 di agram --w ir in g (old) 079691 --75 1 1 000 fi lt er a. --* m 22* x79163 1 1 1...
Page 43
Qs12/24 074063--22.
Page 44
Qs12/24 074063--23.
Page 45
Qs12/24 074063--75 rev. 4/01.
Page 46
Qs24 078807--23.
Page 47
Qs24 079691--77 j710000 -- j9050000