1. DL manuals
  2. TC-Helicon
  3. Music Pedal
  4. VoiceTone D1
  5. User Manual

TC-Helicon VoiceTone D1 User Manual

Summary of VoiceTone D1

  • Page 1

    Voicetone d 1 user’s manual.

  • Page 2

    Important safety instructions 1 read these instructions. 2 keep these instructions. 3 heed all warnings. 4 follow all instructions. 5 do not use this apparatus near water. 6 clean only with dry cloth. 7 do not block any ventilation openings. Install in accor- dance with the manufacturer’s instructio...

  • Page 3

    This equipment generates, uses and can radiate radio frequency energy and – if not installed and used in accordance with the instructions – may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this eq...

  • Page 4: (En) Introduction

    Www.Tc-helicon.Com - www.Youtube.Com/tchelicon (en) introduction voicetone d1 thickens your voice with realistic doubling emulations in an easy-to-use pedal. Using tc-helicon’s refined vocal algorithms, voicetone d1 provides that cool unison doubling effect used by successful artists since the dawn ...

  • Page 5

    1 - effect on/off footswitch 2 - effect active led indicator 3 - doubling style selector 4 - mic gain control for input level 5 - balanced xlr mic input 6 - balanced xlr mono output 7 - power in 8 - usb connector to computer 9 - input level led; green=signal, red=clip 10 - effect on/off via optional...

  • Page 6: Connecting

    Connecting mic jack - connect your mic here using a balanced xlr cable. Phantom power is always on. Out jack - connect to your pa mixer, another voicetone pedal or powered speaker. Power in - connect the supplied 12vdc power supply. Usb - connect to a computer running the tc-helicon voicesupport app...

  • Page 7: First Setup And Use

    First setup and use 1. Turn down your pa’s master volume. 2. Connect your mic and pa as shown in the diagram first, then plug in the ac adaptor. For live performance, a usb connection to a computer is not required. 3. Set the style to tight and the mix control to the center notch. 4. Sing into your ...

  • Page 8: Effect Descriptions

    Effect descriptions doubling styles - the following table offers an overview of the different factory styles. Doubling is mostly used either to highlight a word, phrase or chorus. To use the effect for an entire song, it’s a good idea to use a subtle style (tight or detune) or use a more obvious one...

  • Page 9

    Using multiple voicetone single pedals it is possible (even encouraged!) to use more than one voicetone pedal at a time. You will only need to adjust the mic gain control of the first pedal in the chain. On the rest, mic gain should be set to the minimum (fully left) position. The order of the pedal...

  • Page 10: Tips For Avoiding Feedback

    2. Install voicesupport on your computer. 3. Connect your product via usb to your computer. 4. Run voicesupport. 5. Read the news, click on tabs and browse the features of the application. Using the mic control feature mic control allows you to turn effects on and off from the optional tc-helicon mp...

  • Page 11: Faq

    Faq why am i hearing distortion? Likely the mic gain knob is set too high. Ensure that the input led is green most of the time with only brief and rare peaks of red. Can i use the product on an auxiliary send/return? Yes. You will need balanced xlr to trs cables to do so. Ensure that the mic gain kn...

  • Page 12

    (en) technical specifications input mic input impedance: balanced: 2.68 kohm mic input level @ 0 dbfs: -42dbu to +1dbu ein @ max mic gain rg = 150 ohm: -126 dbu mic input snr: >104 db output output impedance, bal./unbal.: 200/100 ohm output full scale: +1 dbu dynamic range: >104 db, 20 hz to 20 khz ...