TE REC-Li250M User Manual - page 12
Customer Manual
取扱説明書
409-78004
Rev A
12 of 31
3.
3.
3.
3.
Insert
Insert
Insert
Insert Nest
Nest
Nest
Nest die into the Yoke
die into the Yoke
die into the Yoke
die into the Yoke and the Indent
and the Indent
and the Indent
and the Indent die
die
die
die adapter and the Indent die
adapter and the Indent die
adapter and the Indent die
adapter and the Indent die to the
to the
to the
to the Ram securely
Ram securely
Ram securely
Ram securely.
.
.
.
4.
4.
4.
4.
Close the Yoke and push the Slide pin in securely.
Close the Yoke and push the Slide pin in securely.
Close the Yoke and push the Slide pin in securely.
Close the Yoke and push the Slide pin in securely.
5.
5.
5.
5.
Turn the Slide pin clockwise to lock. If the Slide pin is not locked securely, it
Turn the Slide pin clockwise to lock. If the Slide pin is not locked securely, it
Turn the Slide pin clockwise to lock. If the Slide pin is not locked securely, it
Turn the Slide pin clockwise to lock. If the Slide pin is not locked securely, it may break during the
may break during the
may break during the
may break during the
operation.
operation.
operation.
operation.
6.
6.
6.
6.
The head is 180
The head is 180
The head is 180
The head is 180°
°
°
°rotatable. Rotate the head to the desired position for the job.
rotatable. Rotate the head to the desired position for the job.
rotatable. Rotate the head to the desired position for the job.
rotatable. Rotate the head to the desired position for the job.
7.
7.
7.
7.
Place the connector and p
Place the connector and p
Place the connector and p
Place the connector and press the Trigger and advance the ram so that
ress the Trigger and advance the ram so that
ress the Trigger and advance the ram so that
ress the Trigger and advance the ram so that
the connector is held between
the connector is held between
the connector is held between
the connector is held between
the die
the die
the die
the dies.
s.
s.
s.
8.
8.
8.
8.
When crimping terminal or sleeve(P), i
When crimping terminal or sleeve(P), i
When crimping terminal or sleeve(P), i
When crimping terminal or sleeve(P), insert the conductor
nsert the conductor
nsert the conductor
nsert the conductor until it sticks out 1mm from its barrel edge
until it sticks out 1mm from its barrel edge
until it sticks out 1mm from its barrel edge
until it sticks out 1mm from its barrel edge.
.
.
.
When crimping sleeve(B), insert the conductor as far as it goes.
When crimping sleeve(B), insert the conductor as far as it goes.
When crimping sleeve(B), insert the conductor as far as it goes.
When crimping sleeve(B), insert the conductor as far as it goes.
9.
9.
9.
9. Press the Trigger until the compression is
Press the Trigger until the compression is
Press the Trigger until the compression is
Press the Trigger until the compression is
completed.
completed.
completed.
completed.
A click will be heard w
A click will be heard w
A click will be heard w
A click will be heard when completed.
hen completed.
hen completed.
hen completed. The black band around the
The black band around the
The black band around the
The black band around the
Ram becomes visible when the Ram is fully extended.
Ram becomes visible when the Ram is fully extended.
Ram becomes visible when the Ram is fully extended.
Ram becomes visible when the Ram is fully extended.
10.
10.
10.
10. Press the Release
Press the Release
Press the Release
Press the Release lever
lever
lever
lever to retract the Ram. The Ram
to retract the Ram. The Ram
to retract the Ram. The Ram
to retract the Ram. The Ram
continues to retract while the Release
continues to retract while the Release
continues to retract while the Release
continues to retract while the Release lever
lever
lever
lever is
is
is
is
pressed. The
pressed. The
pressed. The
pressed. The
Ram stops when it reaches the low
Ram stops when it reaches the low
Ram stops when it reaches the low
Ram stops when it reaches the lower end.
er end.
er end.
er end.
11.
11.
11.
11.
To release and pull out the Slide pin, follow the procedure as described in step 2.
To release and pull out the Slide pin, follow the procedure as described in step 2.
To release and pull out the Slide pin, follow the procedure as described in step 2.
To release and pull out the Slide pin, follow the procedure as described in step 2.
12.
12.
12.
12.
Open the Yoke and remove the crimped conductor.
Open the Yoke and remove the crimped conductor.
Open the Yoke and remove the crimped conductor.
Open the Yoke and remove the crimped conductor.
13.
13.
13.
13.
If crimping 200mm2 or 250mm2, change the Yoke and follow the steps from step 2.
If crimping 200mm2 or 250mm2, change the Yoke and follow the steps from step 2.
If crimping 200mm2 or 250mm2, change the Yoke and follow the steps from step 2.
If crimping 200mm2 or 250mm2, change the Yoke and follow the steps from step 2.
Note: To maintain long life of the Li-Ion battery, the protection feature to stop the output is installed. When
the trigger is pressed with low battery capacity, the motor stops. It is the function of the protection
feature and not an electrical breakdown. Charge the battery if it happens.