DL manuals
TE
Chassis
TECP-90-703
Installation manual

TE TECP-90-703 Installation manual

Page of 8

Download

Print this page

Bookmark us

300001749244 Rev A

Page 1

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

PRODUCT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

MAIN COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

GROUNDING AND BONDING THE CHASSIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

CHASSIS INSTALLATION PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

DOOR INSTALLATION AND OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

WHERE TO FIND OTHER INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

6.1

Adapter Pack and Module Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

6.2

Routing of Cables, Fibers, and Patch Cords. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

6.3

Phone Numbers, Mail Address, Email Address, and Product Portal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

INTRODUCTION

This installation manual describes the NG4access ODF Platform Standard Chassis and provides

all information needed to install this product. This product is intended to be used in a Network

Telecommunication Facilities and is suitable for installation in an Integrated Bonding Network

or a Common Bonding Network.

Content

Page

24939-A

TECP-90-703

 Issue 1  8/2012

NG4access ODF Platform

Standard Chassis

Installation Manual

1 2 3 4 5 6 7 Next › »

Summary of TECP-90-703

Page 1
300001749244 rev a page 1 © 2012 tyco electronics corporation. All rights reserved. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1 product description . . . . . . . . . . . . ....
Page 2
Tecp-90-703 • issue 1 • 8/2012 page 2 © 2012 tyco electronics corportation. All rights reserved. Revision history trademark information te (icon), te connectivity (logo), and ng4access are trademarks of tyco electronics corporation. Admonishments admonishments — in the form of dangers, warnings, and...
Page 3
Tecp-90-703 • issue 1 • 8/2012 page 3 © 2012 tyco electronics corporation. All rights reserved. • access trays can also be loaded with cabled modules that snap into position. Each cabled module is pre-terminated with 24 lc or 12 sc adapter/connectors and fibers. Snap-in mpo and vam modules are also ...
Page 4
Tecp-90-703 • issue 1 • 8/2012 page 4 © 2012 tyco electronics corportation. All rights reserved. • guide strip—provides cable management for fibers routed into the chassis on the front or rear of the frame. 3 grounding and bonding the chassis the standard chassis uses thread-forming mounting screws ...
Page 5
Tecp-90-703 • issue 1 • 8/2012 page 5 © 2012 tyco electronics corporation. All rights reserved. 3. Install guide strips (provided) on front and rear of chassis. To install a strip, align the tabs on the strip with the slots on the chassis as shown in rear view in figure 3 , then press the radius lim...
Page 6
Tecp-90-703 • issue 1 • 8/2012 page 6 © 2012 tyco electronics corportation. All rights reserved. 5 door installation and operation the standard chassis is equipped with a separately packed door that when installed protects the access trays when the chassis is not being accessed. To install the door:...
Page 7
Tecp-90-703 • issue 1 • 8/2012 page 7 © 2012 tyco electronics corporation. All rights reserved. Figure 5. Closing door figure 6. Door in full open position retract slides and flip up to close 25075-a 25074-a.
Page 8
Tecp-90-703 • issue 1 • 8/2012 page 8 © 2012 tyco electronics corportation. All rights reserved. 6 where to find other information 6.1 adapter pack and module installation instructions refer to the laminated cards hanging on the rear of the frame. 6.2 routing of cables, fibers, and patch cords for c...