1. DL manuals
  2. Teac
  3. LCD TV
  4. LCDV3257DVR
  5. User Manual

Teac LCDV3257DVR User Manual - System Connections

Manual is about: 32" HD Wide Screen

Summary of LCDV3257DVR

  • Page 1

    Product image to be inserted user manual warranty information inside. Please read www.Teac.Com.Au important ! Trademark of teac corporation japan 32” hd wide screen lcd tv lcdv3257dvr.

  • Page 2

    Warranty procedure v1.5.2: dec 2011 please read the owner’s manual carefully and ensure that you have followed the correct installation and operating procedures. 1. Please read this warranty card. 2. Keep your purchase receipt to enable you to proceed quickly in the event of a warranty service. 3. I...

  • Page 3

    Warranty information v1.5.2: dec 2011 our goods come w it h guar ant ees t hat cannot be excluded under t he australian consumer law . You ar e ent it led to a replacement or ref und f or a major failur e and for compensat ion f or any ot her reasonably foreseeable loss or damage. You are also ent i...

  • Page 4: Table Of Contents

    1 table of contents important safety instructions ..................................................................................................................................... 2 supplied accessories ................................................................................................

  • Page 5

    2 important safety instructions caution: use of any controls, adjustments, or procedures other than those specified herein may result in hazardous radiation exposure. Caution 1. The product contains a low-power device. In order to ensure the safety of the laser device, do not remove any cover and at...

  • Page 6

    3 important safety instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Maintain well ventilated conditions around the product. Do not p...

  • Page 7: Supplied Accessories

    4 supplied accessories make sure that the following accessories are provide with the product. Item name qty remote control 1 batteries for remote control 2 av cables 1 user manual 1 note: accessories and their numbers are subject to modification without prior notice..

  • Page 8: View Of Unit

    5 view of unit right side panel 1. Input button press to enter the source selecting menu, press the ▲▼ direction buttons to select desired mode and press the enter button to enter the selected mode. In system setup menu, this button also serves as the enter button. 2. Menu button press to enter the ...

  • Page 9: View Of Unit

    6 view of unit left side panel 6. Eject button press to eject the disc from the unit. 7. ■ stop button press to stop disc playback in dvd mode. 8. Play/pause button press to start disc playback and press it again to pause playback in dvd mode . 9. Disc tray slot insert disc into this slot. 10. Sd/ms...

  • Page 10: View Of Unit

    7 view of unit rear panel.

  • Page 11: View Of Unit

    8 view of unit 1. Usb port connect the usb device for dvr record/playback and software upgrade. 2. Hdmi 1 and hdmi 2 input jacks connect the hdmi signal source. 3. Vga in jack connect the vga signal source in vga mode. 4. Composite 2 and l/r audio input jacks connect composite signal source in compo...

  • Page 12

    9 stand and wall-mounted (optional) your lcd tv is able to accommodate wall mounting with the use of a wall mount bracket (not supplied with lcd tv, please contact your local hardware store) and the mounting holes on the back of the unit. We recommend removing the tv stand prior to wall mounting the...

  • Page 13

    10 special feature of dvd module your tv comes equipped with a removable dvd module. Please follow the procedures below to remove or install the dvd module. Note: before removing or installing the dvd module, ensure that the television is unplugged and turned off. Dvd module removal: refer to the il...

  • Page 14: Disc Information

    11 disc information discs supported disc logo contents size maximum time 133min(ss-sl) 242min(ss-dl) 266min(ds-sl) dvd audio + video (active picture) 12cm 484min(ds-dl) cd audio 12cm 74min jpeg still high resolution 12cm avi audio + video 12cm — the operating method of some dvd discs is specified by...

  • Page 15: Remote Control

    12 remote control remote control drawing 1. Power button press to enter or exit standby mode. 2. Dtv button press to enter dtv mode. 3. Sound button press to select the screen picture mode: choose from standard, user, sports, movie or music. 4. Tv.Radio button press to select dtv program playback or...

  • Page 16: Remote Control

    13 remote control 11. Audio button in dvd mode, press to select the audio language or audio track. In teletext mode, press once to display the concealed information, such as solution of riddles or puzzles; press again to remove the riddles answers from the display. 12. Ch.List button press to displa...

  • Page 17: Remote Control

    14 remote control remote control drawing 32. Card button press to display the media selecting menu in dvd mode. In teletext mode, press to select four groups of 3-digit numbers that are displayed in different colors at the bottom of the screen. Press the colour buttons on the remote control to selec...

  • Page 18: Remote Control

    15 remote control preparation of remote control softly push the back cover to open the battery compartment. Insert two batteries (1.5v, size aa), please make sure the polarity matches the marks inside the compartment. Softly press the back cover to close it. — under normal use the battery will last ...

  • Page 19: System Connections

    16 system connections — do not connect the power cord until all other connections have been made. — ensure that you observe the color code when connecting audio and video cables. Connecting to the power supply connect the power supply cord to ac 100~240v wall outlet, see the figure below: connecting...

  • Page 20: System Connections

    17 system connections connecting to an external av signal source (av1/s-video) use the av cables to connect the external av signal source to the av input jacks on the rear panel of the unit. Use a s-video cable (not supplied) to connect the external av signal source to the s-video input jack on the ...

  • Page 21: System Connections

    18 system connections connecting to an external av signal source (av2) use the av cables to connect the external av signal source to the av input jacks on the rear panel of the unit. After connection, turn on the power of the unit and the external av signal source. Press input then direction buttons...

  • Page 22: System Connections

    19 system connections connecting to an external av signal source (ypbpr) use av cables to connect an external av signal source to the y/pb /pr (component) input jacks on the rear panel of the unit. After connection, turn on the power of the unit and the external av signal source. Press input then di...

  • Page 23: System Connections

    20 system connections connecting to an external av signal source (hdmi) follow the figure below to connect an hdmi signal source to one of the hdmi jacks on the rear panel of the unit. After connection, turn on the power of the unit and the external av signal source. Press input then direction butto...

  • Page 24: System Connections

    21 system connections connecting to an external signal source (av output) use the av cables to connect the external av input device to the av output jacks on the rear panel of the unit. After connection, turn on the power of the unit and the external av signal source. Press input then direction butt...

  • Page 25: System Connections

    22 system connections connecting a coaxial digital output this unit is designed with a coaxial digital audio jack, can be connected to the digital amplifier, see the figure below: — this feature is available only for amplifiers equipped with coaxial digital audio input connectors. Connecting a usb d...

  • Page 26: System Connections

    23 system connections connecting to a pc follow the steps and figure below to connect a pc to the unit. 1. Connect one end of the vga cable to the vga in jack on the jack panel of the unit and the other end to the pc vga output. 2. Connect one end of the audio cables to the vga audio in jack on the ...

  • Page 27: Input Source Selecting

    24 input source selecting the unit incorporates multiple input sources which can be selected via the input button on the television or remote. Press the input button to enter input menu. The screen will display as shown below: use the ▲▼direction buttons and enter button on the input menu, press the...

  • Page 28: Preparations

    25 tv operation and system setup preparations 1. After connection, press the power button to turn on the unit. 2. Press the input button to select atv or dtv mode and you can then conduct the following operations: note: in other mode, you can refer to the following instructions in dtv or atv mode to...

  • Page 29: Channel Setting

    26 tv operation and system setup if you use the unit for the first time or if your setup has changed, you can setup the unit from channel setup menu. Please follow the instructions below: channel setting press the menu button once to enter channel setup menu as shown on the right. Press the enter or...

  • Page 30

    27 tv operation and system setup dtv manual tuning press the ▲▼ button to select dtv manual tuning and press the enter or ► button, the screen will display as shown on the right: press the ◄► button to select desired channel number and press the enter button to start tuning. Atv manual tuning press ...

  • Page 31: Picture Setting

    28 tv operation and system setup rename a channel: (this function is only available for atv channels) press the ▲▼ button to select a channel you want to rename and press the green button to set a symbol “ ” on the channel. Press the ◄► button to highlight the character position of channel name and ...

  • Page 32

    29 tv operation and system setup brightness press the ▲▼ button to select brightness and press the ◄► or enter button to enter the brightness adjusting bar. Press the ◄► button to darken or brighten the picture. Color press the ▲▼ button to select color and press the ◄► or enter button to enter the ...

  • Page 33

    30 tv operation and system setup blue press the ▲▼ button to select blue and press the ◄► or enter button to enter the adjusting bar. Press the ◄► button to select adjust the level. Note: — the items red, green and blue are only available when color temperature is set to user. — within the adjusting...

  • Page 34: Sound Setting

    31 tv operation and system setup sound setting press the menu button once to enter channel setup menu and press the ▲▼ button to select sound, the screen will display as shown. Press the enter or ► button to enter the menu. In the sound setup menu, press the ▲▼ button to select the desired item. Pre...

  • Page 35: Time Setting

    32 tv operation and system setup surround sound press the ▲▼ button to select surround sound and press the ◄► button to select off, srs trusurround xt or surround. Surround mode press the ▲▼ button to select surround mode and press the ► or enter button to enter the sub menu as shown: within the sub...

  • Page 36: Option Setting

    33 tv operation and system setup off time press the ▲▼ button to select off time and press the enter or ► button to prompt a information box, as shown: press the ▲▼ button to select repeat, hour or minute, press the ◄► button to set. Press the enter button to confirm after selecting close. On time p...

  • Page 37

    34 tv operation and system setup audio language press the ▲▼ button to select audio language and press the enter or ► button to prompt a information box, as shown: press the ▲▼ button to select primary or secondary, press the ◄► button to select desired language. Press the enter button to confirm be...

  • Page 38

    35 tv operation and system setup osd time out this item is used to set the duration of the osd on the screen. Press the ▲▼ button to select osd time out and press the ◄► button to select desired time. Dvr file system press the ▲▼ button to select dvr file system and press the ► or enter button to en...

  • Page 39

    36 tv operation and system setup during disk formatting, please do not unplug the usb device and wait for several minutes. Notes: we cannot guarantee compatibility (operation and/or bus power) with all usb mass storage devices and assumes no responsibility for any loss of data that may occur when co...

  • Page 40

    37 tv operation and system setup allow update press the ▲▼ button to select allow update and press the ◄► button to select on or off. System update time set the time when the system update automatically in standby mode. Press the ▲▼ button to select system update time and press the ► or enter button...

  • Page 41: Dvr Function

    38 dvr function in dtv mode only dvr function allows the unit to record live dtv program and make it available for reviewing at any time. Note: when dvr function is in progress, please do not unplug the power and external usb device at will. When dvr function is active, the power indicator will blin...

  • Page 42: Dvr Function

    39 dvr function 3. While in time shift mode, operations below can be use d. Press the or button repeatedly to increases the fast forward/rewind speed. Press the button to jump about 30 seconds forward. Press the button to jump about 30 seconds backward. Press the button once to set the beginning poi...

  • Page 43: Dvr Function

    40 dvr function playing recorded program the digital video recording list contains a list of past recorded programs. 1. Press the dvr.List button on the remote control to enter the recorded list, as shown: press the dvr.List button repeatedly to list the files in the order of either program, channel...

  • Page 44: Dvr Function

    41 dvr function schedule recording schedule recording is a function which permits the recording of future programs. This automated command can be set by the user with reference to the local program guide. 1. Press the guide button to display the electronic program guide menu, as shown: 2. Select you...

  • Page 45: Dvr Function

    42 dvr function 5. Use the ▲▼ button to select desired item and press the enter button to enter. Program select a program. Start date set a date to start recording in the future. The start date should be later than the current date. Start time set a time to start recording in the future. The start t...

  • Page 46: Epg Function

    43 epg function in dtv mode only this system has an electronic program guide (epg) to help your navigation through all the possible viewing options. The epg supplies information such as program listings, start and end times for all available services. In addition, the detailed information about the ...

  • Page 47: Epg Function

    44 epg function to schedule a program reminder select a program on the program guide menu then press the blue button to enter the reminder menu, as shown on the right: if you want to adjust any of the settings, press the ▲▼ button to select desired item and press the ◄► button to set it. Press the e...

  • Page 48: Nicam Function

    45 nicam function the unit supports nicam function when in tv mode. Under nicam tv broadcast: 1. When receiving stereo audio signals, press the stereo button on the remote control repeatedly to select the sound tracks between nicam stereo and mono and the screen will show the corresponding display a...

  • Page 49: Dvd Playback Operation

    46 dvd playback operation preparation 1. Connect the unit to the power supply and press the power button to turn on the unit. 2. Repeatedly press the input button on the remote control to select dvd mode and press the enter button to enter. 3. Gently insert the disc, with the label side toward the f...

  • Page 50: Dvd Playback Operation

    47 dvd playback operation previous and next press the button to go to the next chapter. Press the button once to return to the beginning of the current chapter or track; press it twice to go to the previous chapter. Fast playback during playback, press the button to activate fast rewind or fast forw...

  • Page 51: Dvd Playback Operation

    48 dvd playback operation subtitle s the on board dvd player is capable of supporting dvds with multiple language selections. To access the subtitle selection on a multi-subtitle disc, press the subtitle button on the remote control during play, and select the user prefered option. — some dvds do no...

  • Page 52: Dvd Playback Operation

    49 dvd playback operation jpeg playback jpeg is a common picture format that requires small amounts of storage per image and has low loss in resolution. Hundreds of pictures can be stored on a disc in this format. In order to view jpeg photo albums, you can ask your film development company to make ...

  • Page 53: Dvd Playback Operation

    50 dvd playback operation avi playback avi is the name of a revolutionary new video code, which is based on the new avi compression standard for video. 1. Load an avi disc in the disc tray, the player will enter the reading mode. 2. The screen displays the root menu. Use the ▲▼ buttons to select des...

  • Page 54: Dvd Playback Operation

    51 dvd playback operation usb and sd/ms/mmc card function in dvd mode, connect usb device to the usb port or insert sd/ms/mmc card into the sd/ms/mmc card slot on the left side of the unit. — make sure that files are stored in the usb and sd/ms/mmc card before connection. 1. When you turn on the uni...

  • Page 55: Dvd System Setup

    52 dvd system setup this is the place where you can arrange all important settings for the cooperation of the dvd with the tv set and other audio equipment. General operating steps 1. Press the input button to change to dvd mode. Press the setup button on the remote control, the settings menu will a...

  • Page 56: Dvd Setup Menu

    53 dvd setup menu osd lang please select preferred language for the osd menus. Captions you can activate the captions display during playback with “on” or deactivate the display with “off”. Screen saver when activated, under stop mode, the unit will go into screen saver mode if the same image remain...

  • Page 57: Dvd Setup Menu

    54 dvd setup menu dolby digital setup: dual mono this function is used to set audio output. Stereo: stereo signal output. L-mono: left audio channel signal output. R-mono: right audio channel signal output. Mix-mono: output of left and right mixed audio signals. Dynamic use this function for setting...

  • Page 58: Dvd Setup Menu

    55 dvd setup menu sharpness this menu allows the settings for the sharpness of the picture: ”high“, “medium“ or “low“ . Select "low" for a soft image and "high" to improve a blurry image. Brightness and contrast used to set the brightness and contrast of the image to conform to the surrounding light...

  • Page 59: Dvd Setup Menu

    56 dvd setup menu audio, subtitle and disc menu if a dvd contains several languages, you can choose the language for the playback, subtitles and dvd menu. Default this option is used to reset the unit. The factory settings are adopted. Notes: — resetting is only possible when the disk is removed fro...

  • Page 60: Troubleshooting

    57 troubleshooting symptom check item the player cannot play. Make sure the disc is loaded in. Make sure the disc is not dirty or warped. Make sure the player’s region code is the same as the region code of the dvd disc. Make sure water condensation has not occurred. If it occurs, take out the disc ...

  • Page 61: Specifications

    58 specifications model lcdv3257dvr screen size 32-inch tft lcd tv native resolution 1366 × 768 pixels brightness 500 cd/m 2 contrast ratio 2500 :1 response time (ms) 6.5 ms color system pal sound system bg/i/dk tuner vhf/uhf: 48.25~863.25mhz antenna 75Ω vhf/uhf input stereo nicam/a2 max supported u...

  • Page 62

    Teac customer support hotline (tcs) 1300 553 315 between monday to friday – aest 8.30am to 6pm.