1. DL manuals
  2. Theben
  3. Security System
  4. PresenceLight 180A-KNX series
  5. Operating Manual

Theben PresenceLight 180A-KNX series Operating Manual

Manual is about: Presence Detector

Summary of PresenceLight 180A-KNX series

  • Page 1

    1103066201 © 05.2011 theben hts presencelight 180a-knx .. Presencelight 360a-knx .. Presencelight 180b-knx .. Presencelight 360b-knx .. Presence detector dk d f gb e i nl s n fin bedienungsanleitung 2 notice d´utilisation 32 operating manual 62 manual de instrucciones 92 istruzioni per l´uso 122 geb...

  • Page 2: English

    62 english operating manual presence detector presencelight 180a-knx .. Presencelight 360a-knx .. Presencelight 180b-knx .. Presencelight 360b-knx .. Table of contents 1. Safety . . . . . . . . . . . . . . . . . . . .63 2. Function and performance . . . .63 3. Location . . . . . . . . . . . . . . . ...

  • Page 3: 1.  Safety

    63 gb 1. Safety familiarise yourself with the presence detecors presencelight 360 knx and pres- encelight 180 knx before assembly and startup by reading this operating instruc- tions. ! Caution! The unit requires no maintenance. Opening the unit or inserting foreign bodies into it will invalidate th...

  • Page 4

    64 ● control of one or two lighting groups ● switching or constant light control with stand-by function ● fully or semi-automatic function mode ● presence channel with switch-off delay and switch-on delay time ● channel monitoring with manipulation protection ● channel brightness (lux) ● parallel ci...

  • Page 5: 2.1  Control Type

    65 gb 2.1 control type switching the lighting switches on in case of presence and insufficient brightness, and off in case of absence or sufficient brightness. Constant light control in constant light control mode, the brightness is constantly maintained at th pre- set value. It can be started fully...

  • Page 6: 3.  Location

    66 3. Location 3.1 detection range presencelight 360x-knx the ideal mounting height is 2,0–3,0 m. The sensitivity of the detector decreases with increasing mounting height. In order to ensure proper detection of persons, the presencelight 360x-knx requires an unobstructed “view” of the persons. Of- ...

  • Page 7

    67 gb presencelight 360x-knx presencelight 180x-knx 2 3 1 0 m 0 2 3 1 1 2 3 3.5 0.8 3.5 lux 3,5 3,5 3 2 1 1 2 3 0 3, 5 3 2 1 1 2 3 0 o o 2,2 m 1 2 3 5 6 7 8 0 4 0 2 1 3 0 2 1 3 2 1 3 5 6 7 8 4 5 6 7 8 4.

  • Page 8: 3.3  Light Measurement

    68 3.3 light measurement the detector measures artificial and daylight that is reflected directly below the detector (aperture ± 30°). The surface brightness below the installation site is used as a lighting level reference. Switching with indirect lighting, the artificial light at the detector inst...

  • Page 9: 4.  Installation

    69 gb 4. Installation 4.1 general fitting flush-mounting the presence detector will be flush mounted into a concealed housing. The enclosed set of seals is to be used for ip 54 installation. Surface-mounting a suitable frame for surface mounting is also available. If the surface-mounting seal set is...

  • Page 10

    70 surface-mounting ip 40 a suitable frame for surface mounting is also available. The surface-mounting frame is prepared for cable feed-through with metric cable glands (m16 or m20). 4.3 protection class ip 54 device types: presencelight 180b-knx .. , presencelight 360b-knx .. Flush-mounting ip 54 ...

  • Page 11: 5.  Start-Up

    71 gb 5. Start-up 5.1 settings all settings are adjusted using ets. See ‘knx handbook presencelight 180 knx / presencelight 360 knx’ document (application description). The management remote control sendopro 868-a is optionally available for sup- port during the installation. The sendopro 868-a can ...

  • Page 12: 5.5  Operation Mode

    72 activation description powerup press and hold the program button while switching on the bus voltage. 5.5 operation mode the presencelight 180x-knx and presencelightx-360 knx have 3 operation modes: ● normal ● test presence (page 75) ● test light (page 77) 5.6 switch-on behaviour after every time ...

  • Page 13

    73 gb 6. Alterable parameters via remote control the following parameters can be adjusted and optimised via the management re- mote control sendopro 868-a for support during installation as well as servicing. This adjustment of parameters does not change the settings in ets. Parameter chapter / page...

  • Page 14: Value Range

    74 6.2 brightness level channel a light brightness level define the minimum brightness required. Current prevalent bright- ness is measured below the presence detector. If the prevalent brightness is below the setpoint value, the light will switch on as long as presence is detected (with function mo...

  • Page 15: 7.  Test-Mode

    75 gb if setting values for brightness faster response to changes in actual brightness when in operating mode switching of one lighting row. 7. Test-mode the presencelight has two test modes. ● test presence, page 75 ● test lighting, page 77 the test mode can only be started with voltage. 7.1 test p...

  • Page 16: Test Response

    76 led display channel status description off with absence (led off) open both channels after 15 sec. Test response - deactivate brightness measurement, light output does not react to brightness - detector does not respond as in fully-automatic function mode, also if semi- automatic is set. - the co...

  • Page 17: 7.2  Test Lighting

    77 gb 7.2 test lighting the test mode test light serves to monitor the brightness set point value (bright- ness threshold). Activate - test lighting «on» with the management remote control sendopro 868-a - via bus object (34) the test lighting can always be activated. Terminate with subsequent resta...

  • Page 18

    78 remote control sendopro 868-a: - terminate test lighting - change alternative brightness level a - change brightness set point channel a light - activate test presence the presence detector resets after the test mode has terminated. ! Do not get the presence detector to switch by means of a flash...

  • Page 19: 8.  Control Commands

    79 gb 8. Control commands the following control commands are available with the management remote control sendopro 868-a: programming mode activating the programming mode teach-in channel a the actual measured brightness value is applied to the brightness level channel a. Transfer is made to current...

  • Page 20: 9.  Troubleshooting

    80 9. Troubleshooting fault cause light does not switch on and/or off when presence and darkness lux value is set too low; detector set on semi-automatic; light was switched off manually via push-buttonor or with sendoclic; person not within detection range; obstruction(s) interrupting detection; sw...

  • Page 21: 9.1  Led Display

    81 gb 9.1 led display led description blinking in 1 second tact the presence detector is in the start-up phase. See page 72. Flickering during 3 sec the command sent from the management remote via infrared is rejected by the presence detector. Is the request consistent with the setting in the presen...

  • Page 22: 10. Technical Data

    82 10. Technical data presencelight 360x-knx detection range horizontal vertical 360º 120º recommended mounting height 2.0 m–3 m maximum range 6 x 6 m (mh 2.5 m) 8 x 8 m (mh 3.5 m) presencelight 180x-knx detection range horizontal 180º recommended mounting height approx. 1.6 m–2.2 m maximum range.

  • Page 23

    83 gb presencelight 360x-knx, presencelight 180x-knx all settings can be set remotely see knx handbook presence- light 180 knx / presencelight 360 knx light measurement mixed light brightness range light measurement deactivated approx. 5–2000 lux measurement off light switch-off delay time 30 s–60 m...

  • Page 24

    84 article numbers presencelight 180a-knx wh, ip 40, white ip 40 200 9 051 presencelight 180a-knx bk, ip 40, black ip 40 200 9 821 presencelight 180a-knx sr, ip 40, silver ip 40 200 9 822 presencelight 180b-knx wh, ip 54, white ip 54 200 9 050 presencelight 180b-knx bk, ip 54, black ip 54 200 9 815 ...

  • Page 25

    85 gb article numbers surface frame presencelight 40wh, ip 40, white 907 0 606 surface frame presencelight 40bk, ip 40, black 907 0 607 surface frame presencelight 40sr, ip 40, silver 907 0 608 surface frame presencelight, incl. Gasket set ip 54, white 907 0 513 surface frame presencelight bk, incl....

  • Page 26: 11. Warranty Declaration

    86 11. Warranty declaration theben hts presence detectors are manufactured and tested for quality with greatest of care and most modern technology. Theben hts ag thus guarantees smooth function with correct use. Should a malfunction appear, theben hts ag guarantees within the scope of the general te...

  • Page 27

    87 gb dimensions presencelight 360x-knx 40,5 60 70 56 38 27 48 45,7 86 4 11.

  • Page 28

    88 dimensions presencelight 180x-knx 70 60 4 11 56 38 32 40,5 86 48 36.

  • Page 29: Ce Declaration of Conformity

    89 gb subject to alteration and printing errors. . Dimensions surface frame for presencelight 360x-knx, presencelight 180x-knx 86 84 24 24 57 70 17,7 22,7 4,5 8 ce declaration of conformity this device complies with the protection regulations of the emc direc- tive 2004/108/ec.

  • Page 30

    Theben ag hohenbergstrasse 32, de-72401 haigerloch tel. +49 (0) 74 74 692 - 0 fax +49 (0) 74 74 692 - 150 hotline tel. +49 (0) 74 74 692 - 369 fax +49 (0) 74 74 692 - 207 hotline@theben.De theben hts ag im langhag 11, ch - 8307 effretikon tel. +41 (0)52 355 17 00 fax +41 (0)52 355 17 01 www.Theben-h...