1. DL manuals
  2. Thecus
  3. Server
  4. 1U4200
  5. User manual

Thecus 1U4200 User manual

Other manuals for 1U4200: User Manual

Summary of 1U4200

  • Page 1

    Thecus n3200xxx/n0503 n4200 series n5200xxx/n5500 1u4200xxx/1u4600 n7700 series n2200xxx n8200xxx/n8800 series user’s manual.

  • Page 2: About This Manual

    2 copyright and trademark notice thecus and other names of thecus products are registered trademarks of thecus technology corp. Microsoft, windows, and the windows logo are registered trademarks of microsoft corporation. Apple, itunes and apple os x are registered trademarks of apple computers, inc....

  • Page 3: Safety Warnings

    3 safety warnings for your safety, please read and follow the following safety warnings: read this manual thoroughly before attempting to set up your thecus ip storage. Your thecus ip storage is a complicated electronic device. Do not attempt to repair it under any circumstances. In the case of malf...

  • Page 4: Table Of Contents

    4 table of contents copyright and trademark notice ................................................. 2 about this manual....................................................................... 2 limited warranty ........................................................................ 2 safety warning...

  • Page 5

    5 wan/lan1................................................................................... 63 lan2........................................................................................... 65 dhcp server configuration ............................................................ 66 storage manage...

  • Page 6

    6 windows.................................................................................... 147 apple os x ................................................................................ 148 mapping thecus ip storage as an iscsi drive....................................148 windows 2000/xp...........

  • Page 7: Chapter 1: Introduction

    7 chapter 1: introduction overview thank you for choosing the thecus ip storage server. The thecus ip storage is an easy-to-use storage server that allows a dedicated approach to storing and distributing data on a network. Data reliability is ensured with raid features that provide data security and...

  • Page 8

    8 printer server with the thecus ip storage’s printer server, you can easily share an ipp printer with other pcs connected to your network. To set up the printer server, refer to chapter 4: external device> printer information. Multiple raid thecus ip storage supports multiple raid volumes on one sy...

  • Page 9

    9 package contents the thecus ip storage should contain the following common items: system unit x1 qig (quick installation guide) x1 cd-title x3 (acronics backup cd , twonky media server cd & universal cd) ethernet cable x1 accessory bag x1 hdd compatibility list card x1 multiple languages warranty ...

  • Page 10

    10 front panel n2200xxx: the thecus n2200xxx’s front panel has the device’s controls, indicators, and hard disk trays: front panel item description power button  powers the n2200xxx on/off. Usb port  usb 2.0 port for compatible usb devices, such as digital cameras, usb disks, and usb printers. Usb...

  • Page 11

    11 n3200xxx: the thecus n3200xxx’s front panel has the device’s controls, indicators, and hard disk trays: front panel item description power led  solid blue: system is powered on wan/lan1 led  solid green: network link  blinking orange: network activity lan2 led  solid green: network link  bli...

  • Page 12

    12 n0503: the thecus n0503’s front panel has the device’s controls, indicators, and hard disk trays: front panel item description power led  solid blue: system is powered on wan/lan1 led  solid green: network link  blinking orange: network activity lan2 led  solid green: network link  blinking ...

  • Page 13

    13 up button ▲  push to scroll up when using the lcd display. Enter button  push to confirm information entered into the lcd display. Escape button esc  push to leave the current lcd menu. N4200 series: the thecus n4200series front panel has the device’s controls, indicators, and hard disk trays:...

  • Page 14

    14 n5200xxx/n5500: the thecus n5500 front panel has the device’s controls, indicators, and hard disk trays: front panel item description 1.System led  blinking orange: system is being upgraded or ;is starting up; data currently inaccessible 2.Wan/lan1 led  solid green: network link  blinking gree...

  • Page 15

    15 n7700 series: the thecus n7700 series front panel has the device’s controls, indicators, and hard disk trays: front panel item description 1.Power led  solid blue: system is power on. 2.System led  solid orange: system is being upgraded or system startup; data currently inaccessible 3.Wan/lan1 ...

  • Page 16

    16 1u4200xxx: the thecus 1u4200xxx front panel has the device’s controls, indicators, and hard disk trays: up button enter button locator button power button reset button down button escape button pwr led busy led error led lan led mute button usb port front panel item description lcd display  disp...

  • Page 17

    17 1u4600: the thecus 1u4600 front panel has the device’s controls, indicators, and hard disk trays: escape button pwr led down button lan2 led power button busy led wan/lan1 led reset button up button usb port lcd display enter button busy led front panel item description wan/lan1 led  solid green...

  • Page 18

    18 n8200xxx/n8800 series: the thecus n8200xxx/n8800 series front panel has the device’s controls, indicators, and hard disk trays: front panel item description 1.Power button  power on/off n8200xxx/n8800 2.Power led  solid green: system is power on. 3.Reboot button  press to system reboot 4.Syste...

  • Page 19

    19 hard disk trays 1u4200xxx/n2200xxx/n8200xxx: each of above mentioned models’ hard disk trays has a lock, a latch, and two led indicators: hard disk trays item description 1.Hdd power led  solid blue: hard disk is powered on 2.Hdd access/error led  blinking green: system is accessing data on the...

  • Page 20

    20 n4200 series/n5200xxx/n5500: each of the n5500’s hard disk trays has a lock, a latch, and two led indicators: hard disk trays item description 1.Hdd power led  solid blue: hard disk is powered on (no function on n4200 series) 2.Hdd access/error led  blinking green: system is accessing data on t...

  • Page 21

    21 n0503: the n0503 supports both 2.5” and 3.5” serial ata (sata) hard disks. To install a hard disk into the n0503, follow the steps below: 3. Open front door of the n0503. 4. For 3.5” hdd a. Get the hard drive rails and place them on either side of the hard drive, fitting into the appropriate groo...

  • Page 22

    22 rear panel n2200xxx: the n2200xxx rear panel features ports and connectors. Back panel item description esata port  esata port for high-speed external storage expansion. Usb port  usb 2.0 port for compatible usb devices, such as digital cameras, usb disks, and usb printers. Wan/lan1 port  wan/...

  • Page 23

    23 n3200xxx/n0503: the n3200xxx/n0503 rear panel features ports and connectors. Back panel item description esata port  esata port for high-speed storage expansion usb port  usb 2.0 port for compatible usb devices, such as digital cameras, usb disks, and usb printers wan/lan1 port  wan/lan1 port ...

  • Page 24

    24 n4200 series: the n4200 rear panel features ports and connectors. Back panel item description power connector for connect the power adaptor wan/lan1 port wan/lan1 port for connecting to an ethernet network through a switch or router lan2 port lan2 port for connecting to an ethernet network throug...

  • Page 25

    25 back panel item description 1.Wan/lan1 port  wan/lan1 port for connecting to an ethernet network through a switch or a router. 2.Lan2 port  lan2 port for connecting to a local ethernet network through a switch or router. 3.Serial port  this port is for an external ups device. 4.Esata port  es...

  • Page 26

    26 n7700 series: the n7700 rear panel features ports and connectors. Back panel item description 1.Lan2 port  lan2 port for connecting to a local ethernet network through a switch or router. 2.Wan/lan1 port  wan/lan1 port for connecting to an ethernet network through a switch or router. 3.Serial p...

  • Page 27

    27 1u4200xxxr: locator led 1u4200 back panel item description esata port  esata port for high-speed storage expansion. Usb ports  usb 2.0 ports for compatible usb devices, such as digital cameras, usb disks, and usb printers. Wan/lan1 port  wan/lan1 port for connecting to an ethernet network thro...

  • Page 28

    28 1u4600r: the rear panel of the 1u4600r houses most of the usb and ethernet connections, as well as the esata port, system fan, and power connector. See the table below for descriptions of each: power connector power connector power switch power switch usb ports (a type) lan2 port power led power ...

  • Page 29

    29 n8200xxx: the n8200xxx rear panel features ports and connectors. 4 7 1 2 3 8 5 6 back panel item description 1.Power connector  connect the included power cords to these connectors. 2.Power switch  powers the n8200xxx on/off. 3.Esata port  esata port for high-speed storage expansion. 4.Usb por...

  • Page 30

    30 n8800 series: the n8800 rear panel features ports and connectors. Back panel item description 1.Power connector  connect the included power cords to these connectors 2.Power switch  switch for power supply 3.Esata port  esata port for high-speed storage expansion 4.Usb port  usb 2.0 port for ...

  • Page 31

    31 chapter 2: hardware installation overview your thecus ip storage is designed for easy installation. To help you get started, the following chapter will help you quickly get your thecus ip storage up and running. Please read it carefully to prevent damaging your unit during installation. Before yo...

  • Page 32

    32 3. Press the power button to boot up the n2200xxx. To connect the n3200xxx/n0503 to your network, follow the steps below: 1. Connect an ethernet cable from your network to the wan/lan1 port on the back panel of the n3200xxx/n0503. 2. Connect the provided power cord into the power socket on the ba...

  • Page 33

    33 3. Open the front door then press the power button to boot up the n3200xxx/n0503. To connect n4200 series nas to your network, follow the steps below: 1. Connect an ethernet cable from your network to the wan/lan1 port on the back panel of the n4200. 2. Connect the provided power cord into the un...

  • Page 34

    34 3. Press the power button on the front panel to boot up the n4200. To connect the n5200xxx/n5500 to your network, follow the steps below: 1. Connect an ethernet cable from your network to the wan/lan1 port on the back panel of the n5200xxx/n5500. 2. Connect the provided power cord into the univer...

  • Page 35

    35 to connect the 1u4200xxx/1u4600 to your network, follow the steps below: 1. Connect an ethernet cable from your network to the wan/lan1 port on the back panel of the 1u4200xxx/1u4600. 2. Connect the provided power cord into the universal power socket on the back panel. Plug the other end of the c...

  • Page 36

    36 to connect n7700 series nas to your network, follow the steps below: 1. Connect an ethernet cable from your network to the wan/lan1 port on the back panel of the n7700. 2. Connect the provided power cord into the universal power socket on the back panel. Plug the other end of the cord into a surg...

  • Page 37

    37 to connect n8200xxx/n8800 series nas to your network, follow the steps below: 1. Connect an ethernet cable from your network to the wan/lan1 port on the back panel of the n8200xxx/n8800. 2. Connect the provided power cord into the universal power socket on the back panel. Plug the other end of th...

  • Page 38

    38 chapter 3: first time setup overview once the hardware is installed, physically connected to your network, and powered on, you can configure the thecus ip storage so that it is accessible to your network users. There are two ways to set up your thecus ip storage: using the thecus setup wizard or ...

  • Page 39

    39 5. Login with the administrator account and password. The default account and password are both “admin”. 6. Name your thecus ip storage and configure the network ip address. If your switch or router is configured as a dhcp server, configuring the thecus ip storage to automatically obtain an ip ad...

  • Page 40

    40 8. Finished! Access the thecus ip storage web administrator interface by pressing the start browser button. You can also configure another thecus ip storage at this point by clicking the setup other device button. Press exit to exit the wizard. Lcd operation (n5200xxx/n5500/1u4200xxx/1u4600/n7700...

  • Page 41

    41 display mode during normal operation, the lcd will be in display mode. Display mode item description host name current host name of the system. Wan/lan1 current wan/lan1 ip setting. Lan2 current lan2 ip setting. Link aggregation current link aggregation status system fan1 current system fan1 stat...

  • Page 42

    42 lcd operation (n3200xxx/n0503) lcd controls use the down ( ▼ ), up ( ▲ ), enter ( ) and escape (esc) keys to operate lcd to view system information and usb copy. The following table illustrates the keys on the front control panel: lcd controls icon function description ▼ down button select the pr...

  • Page 43

    43 4. Press enter ( ) and then3200xxx/n0503 will start copying usb disks connected to the front usb port. The lcd will display the usb copy progress and results. Oled operation (n4200 series) oled operation the n4200 series is equipped with an oled on the front for easy status display and setup. The...

  • Page 44

    44 typical setup procedure from the web administration interface, you can begin to setup your thecus ip storage for use on your network. Setting up the thecus ip storage typically follows the five steps outlined below. For more on how to use the web administration interface, see chapter 4: web admin...

  • Page 45

    45 smb/cifs apple file protocol (afp) network file system (nfs) file transfer protocol (ftp) itunes server printer server photo server.

  • Page 46

    46 chapter 4: system administration overview the thecus ip storage provides an easily accessible web administration interface. With it, you can configure and monitor the thecus ip storage anywhere on the network. Web administration interface make sure your network is connected to the internet. To ac...

  • Page 47

    47 2. Login to the system using the administrator user name and password. The factory defaults are: user name: admin password: admin ※ if you changed your password in the setup wizard, use the new password. Once you are logged in as an administrator disclaimer page will appear as below. Please click...

  • Page 48

    48 administrators can add or remove favorite functions to my favorites by right clicking the mouse on the menu tree. The other way administrators can add favorite functions is by clicking the “add favorite” icon in each function screen. Please refer figure below in red circuit icon. To return to the...

  • Page 49

    49 menu bar the menu bar is where you will find all of the information screens and system settings of thecus ip storage. The various settings are placed in the following groups on the menu bar: menu bar item description system information current system status of the thecus ip storage. System manage...

  • Page 50

    50 message bar you can get information about system status quickly by moving mouse over. Message bar item status description raid information. Display the status of created raid volume. Click to go to raid information page as short cut. Disks information. Display the status of disks installed in the...

  • Page 51

    51 ‧my favorite add/remove the current page from the home page. ‧shutdown choose shutdown or reboot from the dropdown menu to shutdown or reboot your nas. ‧logout click to log out of web administration interface. System information information provides viewing on current product info, system status,...

  • Page 52

    52 system status item description cpu loading (%) displays current cpu workload of the thecus ip storage. Cpu fan speed displays current cpu fan status. System fan speed displays the current status of the system fan. Up time shows how long the system has been up and running. Service status item desc...

  • Page 53

    53 see the following table for a detailed description of each item: system logs item description all provides all log information including system messages, warning messages and error messages. Info records information about system messages. Warn shows only warning messages. Error shows only error m...

  • Page 54

    54 other than the defined items sent upon registration, there are also two additional items: “hdd info” and “time zone”. These two optional items can also be sent to thecus anonymously for analysis and statistics purposes. To send these items, simply check the desired checkboxes to help thecus impro...

  • Page 55

    55 system management the system management menu gives you a wealth of settings that you can use to configure your thecus ip storage system administration functions. You can set up system time, system notifications, and even upgrade firmware from this menu. Date and time: system date and settings fro...

  • Page 56

    56 notification configuration from the menu, choose the notification item, and the notification configuration screen appears. This screen lets you have thecus ip storage notify you in case of any system malfunction. Press apply to confirm all settings. See following table for a detailed description ...

  • Page 57

    57 firmware upgrade from the menu, choose the firmware upgrade item and the firmware upgrade screen appears. Follow the steps below to upgrade your firmware: 1. Use the browse button to find the firmware file. 2. Press apply. 3. The beeper beeps and the busy led blinks until the upgrade is complete....

  • Page 58

    58 example - monday: on: 8:00; off: 16:00 system will turn on at 8:00 am on monday, and off at 16:00 on monday. System will turn on for the rest of the week. If you choose an on time, but do not assign an off time, the system will turn on and remain on until a scheduled off time is reached, or if th...

  • Page 59

    59 see the following table for a detailed description of each item. Change administrator and lcd entry password item description new password type in a new administrator password. Confirm password type the new password again to confirm. Apply press this to save your changes. Config mgmt from the men...

  • Page 60

    60 factory default from the menu, choose the factory default item and the reset to factory default screen appears. Press apply to reset thecus ip storage to factory default settings. Reboot & shutdown from the menu, choose reboot & shutdown item, and the shutdown/reboot system screen appears. Press ...

  • Page 61

    61 once the system has rebooted, you will be returned to the file system check prompt. There you will see the available raid volumes to run the file system check on except zfs volume, zfs has no need to perform file system check. Check the desired raid volumes and click next to proceed with the file...

  • Page 62

    62 wake-up on lan (wol) the thecus ip storage has the ability to be awoken from sleep mode via wan/lan1 port. From the menu, choose the wol item, and the wake-up on lan screen appears. From here, you can enable or disable. Wake-up on lan configuration item description wol service enable or disable w...

  • Page 63

    63 from the menu, choose the snmp item, and the snmp support screen appears. From here, you can enable or disable. Ui login configuration adjusts ui login configuration settings. You can enable/disable the web disk and photo server functions, according to your needs. For the 3x series, users need to...

  • Page 64

    64 wan/lan1 configuration item description host name host name that identifies the thecus ip storage on the network. Domain name specifies the domain name of thecus ip storage. Wins server to set a server name for netbios computer. Mac address mac address of the network interface. Jumbo frame suppor...

  • Page 65

    65 lan2 lan2 configuration the thecus ip storage supports two gigabit ethernet ports for higher service availability. To configure these ports, choose lan2 from the system network menu, and the lan2 configuration screen appears. Press apply to save your changes. Lan2 configuration item description m...

  • Page 66

    66 dhcp server configuration a dhcp server can be configured to assign ip addresses to devices connected to the lan2 port. To configure these ports, choose lan2 from the system network menu. Dhcp configuration item description dhcp server enable or disable the dhcp server to automatically assign ip ...

  • Page 67

    67 disks information item description disk no. Indicates disk location. Capacity shows the sata hard disk capacity. Model displays the sata hard disk model name. Firmware shows the sata hard disk firmware version. Status indicates the status of the disk. Can read ok, warning, or failed. Bad block sc...

  • Page 68

    68 s.M.A.R.T. Information item description tray number tray the hard disk is installed in. Model model name of the installed hard disk. Power on hours count of hours in power-on state. The raw value of this attribute shows total count of hours (or minutes, or seconds, depending on manufacturer) in p...

  • Page 69

    69 raid information from the storage menu, choose the raid item and the raid information screen appears. This screen lists the raid volumes currently residing on the thecus ip storage. From this screen, you can get information about the status of your raid volumes, as well as the capacities allocate...

  • Page 70

    70 stripe size this sets the stripe size to maximize performance of sequential files in a storage volume. Keep the 64k setting unless you require a special file storage layout in the storage volume. A larger stripe size is better for large files. Data percentage the percentage of the raid volume tha...

  • Page 71

    71 once the create button has been pressed with the encryption checkbox enabled, the following message pop-up will appear for confirmation. After the raid volume has been created, you may remove this usb disk until the next time the system boots. The raid volume can not be mounted if the usb disk wi...

  • Page 72

    72 8. Selected the file system you like to have for this raid volume. The selection is available from ext3, xfs and zfs. 9. Press create to build the raid storage volume. Note ．select zfs file system while snapshot is needed. It is only one zfs file system allowed to be created per system. ．zfs file...

  • Page 73

    73 with a raid 1, raid 5, or raid 6 volume, you can also add a spare disk after the raid is created. See chapter 6: tips and tricks > adding a spare disk for details. For more information on raid, see appendix b: raid basics . Raid level you can set the storage volume as jbod, raid 0, raid 1, raid 5...

  • Page 74

    74 remove raid click to remove the raid volume. All user data and iscsi has been created in selected raid volume will be removed. To remove a raid volume, follow the steps below: 1. On the raid list screen, select the raid volume by clicking on its radio button, and click raid information to open th...

  • Page 75

    75 expanding a raid to expand a raid 1, raid 5, or raid 6 volume, follow the steps below: 1. Replace one of the hard drives in the raid volume and allow it to automatically rebuild. 2. Once rebuilt, you can continue to replace any remaining disks in the raid array. 3. When you are done replacing har...

  • Page 76

    76 migrating a raid once a raid volume has been created, you may want to move it to other physical drives or change the raid array all together. To migrate a raid 0, raid 1, raid 5 or raid 6 volume, follow the steps below: 1. From the raid configuration screen, click migrate raid. 2. A list of possi...

  • Page 77

    77 with raid level migration function, the limitation as listed below. 1. During raid level migration, it is not allowed reboot or shutdown system. 2. The raid migration from r1 to r5 or r1 to r6, the all services will restart and volumes “iscsi” is read only but “user data” is capable read / write ...

  • Page 78

    78 below is a table listing of possible raid migration schemes: to from raid 0 raid 5 raid 6 raid 1 [raid 1] hddx2 to [raid 5] hddx3 [raid 1] hddx2 to [raid 5] hddx4 [raid 1] hddx2 to [raid 5] hddx5 [raid 1] hddx2 to [raid 5] hddx6 [raid 1] hddx2 to [raid 5] hddx7 [raid 1] hddx2 to [raid 5] hddx8 ……...

  • Page 79

    79 raid 6 x x [online] [raid 6] hddx4 to [raid 6] hddx5 [raid 6] hddx4 to [raid 6] hddx6 [raid 6] hddx4 to [raid 6] hddx7 [raid 6] hddx4 to [raid 6] hddx8 ………………………………..Hddx16 [raid 6] hddx5 to [raid 6] hddx6 [raid 6] hddx5 to [raid 6] hddx7 [raid 6] hddx5 to [raid 6] hddx8 ………………………………..Hddx16 [rai...

  • Page 80

    80 volume allocation list item description modify click this to modify the allocated space. Delete click this to delete the allocated space. Iscsi target click to allocate space to iscsi volume. Type type of volume. Can be either usb or iscsi. Name name assigned to the volume. Capacity capacity of t...

  • Page 81

    81 to allocate space for an iscsi volume on the current raid volume, follow the steps below: 1. Under the volume allocation list, select iscsi target then click add. The create iscsi volume screen appears. Create iscsi volume item description raid id id of current raid volume. Allocation percentage ...

  • Page 82

    82 8. When iscsi target volume has been created, the lun id is configurable from 1 to 254 with a default of the next available number in ascending numerical order. The lun id is unique and can not be duplicated except for lun id 0. 9. If you’ve enabled chap authentication, enter a username and a pas...

  • Page 83

    83 expand volume the iscsi volume is now able to expand its capacity from unused space. From the volume list, simply select the iscsi volume you like to expand and click the expand button: you will then see the dialog box displayed below. Drag the expand capacity bar to the size you want. Then press...

  • Page 84

    84 2. Press yes. All data in the volume will be removed. Iscsi thin-provisioning with this function, the iscsi capacity can be more flexible and more efficiently serve more users. The idea for iscsi thin-provisioning is sharing the available physical capacity to a number of iscsi target volumes and ...

  • Page 85

    85 next, setup the physical capacity for iscsi thin-provision volume by dragging the allocation bar to the desired size. After the size has been determined, click ok to confirm. Now you will see the iscsi thin-provisioning volume is available from the list. Please refer to the screenshot below..

  • Page 86

    86 now you can start to create iscsi targets to join the newly-created iscsi thin-provision volume. Basically, the iscsi target under iscsi thin-provisioning has exactly same settings screen as the standard iscsi target volume creation. The only difference is the “virtual size” of capacity. Unlike c...

  • Page 87

    87 the screen shot for iscsi target volume creation under thin-provisioning; the physical capacity 333.8gb. The screen shot to setup an iscsi target volume under thin-provisioning of 1700gb. Iscsi target volume creation. The maximum virtual size is 14300gb (16000gb – 1700gb(1 st iscsi target volume)...

  • Page 88

    88 this message appears if there is no more room for new iscsi target creation. Advance option there are 2 options is currently allow admin to enable/disable to operate thecus ip storage associated with iscsi setting. The details as listed in following screenshot. With the option changed, it will ne...

  • Page 89

    89 iscsi block size select the block size with 4k while the iscsi volume size is over 2tb. Iscsi crc/checksum to enable this option, the initiator can connect with “data digest” and “header digest” enabled. Stackable nas the thecus ip storage’s capacity can be expanded even further using the stackab...

  • Page 90

    90 a. Add a stack target volume from the figure above, click add to access the stackable target device configuration page. Please refer to the figure below: with the added stack target you could “enable” or “disable” now or later per usage needed. Next, input the target ip address of the stackable d...

  • Page 91

    91 the export share name will become the network share name and displayed through network access such as smb. You may refer the figures below to see the result. Please note the naming limitation. From the figure above, the export share name is “pmmeeting”. The figures below show the result before an...

  • Page 92

    92 the browseable setting will be same method of setting for system share folder. It designates whether or not this folder will be visible through web disk. You may refer the figures below for reference when yes and no are selected. The public setting will be set same as what the setting for the sys...

  • Page 93

    93 click apply to save your changes. B. Activate a stack target after your settings have been applied, the system will bring you back to stack target list window as shown below. There is one stack target device has been attached into this stack master. With this newly attached stack target device, y...

  • Page 94

    94 after the format is complete, the stack target volume will be created successfully. You will see the volume’s capacity and status in the stack target list screen. C. Edit a stack target to make any changes to stack targets, click edit for the corresponding stack target, and system will bring up t...

  • Page 95

    95 e. Reconnect a stack target the enabled stack target devices may be disconnected by situations such as power outages or network disconnects. When this happens, the reconnect button will available. To attempt to reconnect the stack target, click reconnect. Iso mount the iso mount feature is very u...

  • Page 96

    96 a. Add a iso file from the figure above, select iso file from drop down share list. After selection, system will bring up mount table for further setting screen. To mount new iso file, select from listed iso file and input desired mounting name into “mount as:” field. Click “add” with confirmatio...

  • Page 97

    97 after you have completed to add iso then the page will displayed all mounted iso files, you could click “unmount” to eliminate mounted iso file. B. Using iso the mounted iso file will be located same share folder with name giving. Please refer the screen shot below. Iso file “image” has mounted a...

  • Page 98

    98 share folder from the storage menu, choose share folder, and the folder screen appears. This screen allows you to create and configure folders on the thecus ip storage volume..

  • Page 99

    99 adding folders on the folder screen, press the add button and the add folder screen appears. This screen allows you to add a folder. After entering the information, press apply to create new folder. Add folder item description raid id raid volume where the new folder will reside. Folder name ente...

  • Page 100

    100 modify folders on the folder screen, press the edit button and the modify folder screen appears. This screen allows you to change folder information. After entering the information, press apply to save your changes. Modify folder item description raid id raid volume where the folder will reside....

  • Page 101

    101 nfs share to allow nfs access to the share folder, enable the nfs service, and then set up hosts with access rights by clicking add. Nfs share item description hostname enter the name or ip address of the host privilege host has either read only or writeable access to the folder. Guest system su...

  • Page 102

    102 guest system root account will have full access to this share (root:root). Guest system root account will be mapped to anonymous user (nobody:nogroup) on nas. All user on guest system will be mapped to anonymous user (nobody:nogroup) on nas. Choose the one which best fits your needs. Apply click...

  • Page 103

    103 the thecus ip storage snapshot is supported total 16 versions. Once checked “automatically remove oldest snapshot”, the oldest will be removed to let newest to added on top. Otherwise, if the check box is unchecked and snapshot versions are up to 16 then system will appear warning message and wo...

  • Page 104

    104 acl setting item description deny denies access to users or groups who are displayed in this column. Read only provides read only access to users or groups who are displayed in this column. Writable provides write access to users or groups who are displayed in this column. Recursive enable to in...

  • Page 105

    105 the acl screen also allows you to search for a particular user. To do this, follow the steps below: 1. In the blank, enter the name of the user you would like to find. 2. From the drop down select the group you would like to search for the user in. 3. Click search. Note the system will list up t...

  • Page 106

    106 user and group authentication the thecus ip storage has built-in user database that allows administrators to manage user access using different group policies. From the user and group authentication menu, you can create, modify, and delete users, and assign them to groups that you designate. Ads...

  • Page 107

    107 to join an ad domain, you can refer the figure and use the example below to configure the thecus ip storage for associated filed input: ad domain example item information work group / domain name domain ads support enable ads server name computer1 ads/nt realm domain.Local administrator id admin...

  • Page 108

    108 local user configuration from the accounts menu, choose the user item, and the local user configuration screen appears. This screen allows you to add, edit, and remove local users. Local user configuration item description add press the add button to add a user to the list of local users. Edit p...

  • Page 109

    109 edit users 1. Select an existing user from the local user configuration screen. 2. Click on the edit button, and local user setting screen appears. 3. From here, you can enter a new password and re-enter to confirm, or use the or >> buttons to have this user join or leave a group. Click the appl...

  • Page 110

    110 remove users 1. Select an existing user from the local user configuration screen. 2. Click on remove button and the user is deleted from the system. Local group configuration from the accounts menu, choose the group item, and the local group configuration screen appears. This screen allows you t...

  • Page 111

    111 add groups 1. On the local group configuration screen, click on the add button. 2. The local group setting screen appears. 3. Enter a group name. 4. Enter a group id number. If left blank, the system will automatically assign one. 5. Select users to be in this group from the users list by adding...

  • Page 112

    112 remove groups 1. On the local group configuration screen, select a group name from the list. 2. Press remove to delete the group from the system. Batch create users and groups the thecus ip storage can also add users and groups in batch mode. This enables you to conveniently add numerous users a...

  • Page 113

    113 quota the user quota system provides a way of limiting users’ available storage capacity. Setting a user quota gives a given user a given amount of space on each raid partition. For example, if there are 3 raid partitions and a user has a user quota of 300mb, the user can store 300mb of data on ...

  • Page 114

    114 network service setup and manage protocols such as samba/cifs, ftp, and http/web disk, and other network services. Samba / cifs there are 5 options is currently allow admin to enable/disable to operate thecus ip storage associated with samba / cifs protocol. With the option changed, it will need...

  • Page 115

    115 in general, windows has default to invisible all of hidden folders/files. So please enable this option to view “.Recycle” folder. Samba anonymous login authentication to enable this option, no matter there is share folder has been created in public access. The user account and password is needed...

  • Page 116

    116 nfs setup from the network service menu, choose the nfs item, and the nfs support screen appears. The thecus ip storage can act as an nfs server, enabling users to download and upload files with the favorite nfs clients. Press apply to confirm your settings. A description of each item follows: n...

  • Page 117

    117 public folders. No access: block anonymous ftp user access. Auto rename if checked, the system will automatically rename files that are uploaded with a duplicate file name. The renaming scheme is [filename].# , where # represents an integer. Upload bandwidth you may set the maximum bandwidth all...

  • Page 118

    118 a description of each item follows: web service item description http (webdisk) support enable or disable webdisk support. Enter the port number if this option is enabled. The port number is default 80. Https (secure webdisk) support enable or disable secure webdisk support. Enter the port if th...

  • Page 119

    119 application server thecus ip storage support itunes server functionality, module installation, and auto module installation. The itunes server function allows you to play music files from your nas through itunes on your computer. The following section shows you how. Itunes® server with the built...

  • Page 120

    120 auto module installation or choose the auto module installation item and the available system module screen appears. The default to get module list is “on-line” so if thecus ip storage is capable to connect to internet then it will automatically link to thecus official website then list availabl...

  • Page 121

    121 auto module source list item description installed status of module name module name version the version of released version description the description of module location the module is either getting on-line or disk document the available documentation of module action to install module or dele...

  • Page 122

    122 if the files on your thecus ip storage are lost for any reason, you can restore those files from the target thecus ip storage. To backup files regularly, you can set up a scheduled task to run only once, daily, weekly, or monthly. You can also limit the bandwidth of your nsync tasks, so other us...

  • Page 123

    123 item description task name the name of your nsync task. Target server manufacturer select replication to method, it has 3 options can choose from. Nas: to other thecus ip storage with security tunnel build up. Legacy ftp: to the 3 rd party ftp server or thecus ip storage while it has acted as ft...

  • Page 124

    124 device, make sure there is a folder named “nsync”, and the auth id has writable permission in that folder. Designating thecus ip storage as an nsync target the thecus ip storage can act as an nsync server, enabling another nsync-equipped thecus nas at a remote location backup their files to this...

  • Page 125

    125 rsync target (for the 3x series) when it comes to backing up your data, it’s very important to have flexibility. Rsync backup provides you with many options, including local or remote backup, backup scheduling, different syncronization settings, and password protection. Being based on the linux ...

  • Page 126

    126 *now rsync is turned on on your nas, which means it can be used as a target for rsync backup, in other words, only the backup nas needs to be activated in this way. Rsync (for 3x series) step 2 – setting up your backup task and schedule on your source nas -log in to your other nas (your source n...

  • Page 127

    127 that you wish to backup. 4. Input your target’s ip address and port number - this is the nas which you are going to use as a backup, port number is optional. 5. Input your destination folder and create a backup folder – your destination path is the name of an existing folder on your nas where yo...

  • Page 128

    128 when you execute this utility for the first time, it will ask you whether to create a db file. Click yes. 1. Click add to create a backup task. The add new task dialog box appears. Add new task item description task specifies a name for the current task. Source click to specify the source folder...

  • Page 129

    129 5. Double-click ntbackup.Msi to install the backup utility. Once installed, you can use the windows backup utility by following the steps below: 1. Click start, and point to all programs > accessories > system tools > backup to start the wizard. 2. Click next to skip past the opening page. Choos...

  • Page 130

    130 printer information item description manufacturer displays the name of the usb printer manufacturer. Model displays the model of the usb printer. Status displays the status of the usb printer. Remove document from queue click to remove all documents from printer queue. Restart printer service cl...

  • Page 131

    131 8. Your windows system will ask you if you want to set this printer as “default printer”. Select yes and all your print jobs will be submitted to this printer by default. Click next. 9. Click finish. Note • not all usb printers are supported. Please check thecus website for a list of supported p...

  • Page 132

    132 windows vista to set up the printer server in windows vista, follow the steps below: 1. Open printer folder from the control panel. 2. Click the right mouse button in anywhere on the printers folder and then select add printer. 3. Select add a network, wireless or bluetooth printer..

  • Page 133

    133 4. Select the printer that i want isn’t listed. You can press the printer that i want isn’t listed to go into next page without waiting for searching for available printers to finish. 5. Click select a shared printer by name. Type http://:631/printers/usb-printer in the box, where is the ip addr...

  • Page 134

    134 if your printer model is not listed, please contact your printer manufacturer for help. 7. Windows will attempt to connect to the printer. 8. You can choose to set this printer as the default printer by checking the set as the default printer box. Click next to continue. 9. Done! Click finish..

  • Page 135

    135 ups setting the thecus ip storage can also support various uninterruptible power supply unit via either “serial” or “usb” interface (depend on model) to provide extra data security and accessibility in the case of a power failure. From the status menu, choose the ups item and the ups setting scr...

  • Page 136

    136 chapter 5: using thecus ip storage overview once the thecus ip storage is setup and operating, users on the network may manage all varieties of digital music, photos, or files by simply using their web browsers. To manage your personal files or access public files on the thecus ip storage, just ...

  • Page 137

    137 1. In the login page, type in the user id and password that were previously set for you in the accounts menu. See chapter 4:user and group authentication > local user configuration . 2. The web disk page appears showing folders currently available to you, this is controlled via the access contro...

  • Page 138

    138 folder page button button description list all directory trees per login user’s privilege. Browsing selected directory of its folders and files. Go back to the web disk directory layer. Re-load the current list. Search files in the current web disk directory. (must input the complete file name.)...

  • Page 139

    139 photo server ( does not apply to the 3x series’ photo server ) using the photo server, users can view and share photos, and even create their own albums right on the thecus ip storage. You will see your own photo gallery and all public photo albums on the network. To manage any picture files, yo...

  • Page 140

    140 3. Windows xp will ask whether you want to run or save this file. Click save to save the register file. 4. Once the register file is installed, use the windows file manager to browse the folder that contains the picture you want to publish. On the left pane, there will be an icon labeled “publis...

  • Page 141

    141 6. Select the pictures you want to publish to the photo web server by placing a check mark on the top left hand corner of the picture. Click next. 7. Your pc will start to connect to the photo web server. 8. Select thecus ip storage photo gallery wizard to publish your pictures to thecus ip stor...

  • Page 142

    142 10. Create your album by entering an album name and clicking on the create album button. 11. Select the album you want to upload your pictures to. 12. Confirm the target album. 13. Windows will show you that the picture upload is in progress..

  • Page 143

    143 14. When the upload is finished, the wizard will ask you whether if you want to go to the website. Click finish to go to your photo web server. 15. Click on the user’s icon to go to that user’s album..

  • Page 144

    144 16. You will see the user’s album list. Click on album. 17. Finished! You will see the pictures just selected in the album..

  • Page 145

    145 managing albums and photos icon function description make cover make selected photo your cover picture. Back return to the previous screen. Add add a new album or photos. Modify edit the name and description of the selected album or photo. Each name is limited to 20 characters and each descripti...

  • Page 146

    146 creating albums to create a photo album, follow the steps below: 1. Click the add button to create a new album. 2. Enter a name for the album, and enter a description if you wish. Then, click on the create album button. Password protecting albums if you would like to put a password on a particul...

  • Page 147

    147 slide shows slide shows are a great way to enjoy pictures stored on your thecus ip storage. You can click on the start slide show icon on the top right hand corner to start the slide show. To stop the slide show, click on the stop slide show icon on the top right hand corner. Mapping a client pc...

  • Page 148

    148 apple os x on an apple computer, you can connect to shared computers and servers using a network address. 1. Choose go > connect to server… 2. Enter the network address for the server in the server address text box. When connecting using smb/cifs protocol, type: smb://192.168.1.100/folder1 when ...

  • Page 149

    149 windows 2000/xp 1. First, download the iscsi initiator from the microsoft website ( http://www.Microsoft.Com ). You can find this software by entering iscsi initiator into the search box on their homepage. 2. Once the download is complete, install the iscsi initiator by double-clicking the exe f...

  • Page 150

    150 6. The iscsi initiator will now install automatically. Click finish once completed. 7. Start the iscsi initiator by double-clicking its icon on the desktop. The iscsi initiator properties window will appear. 8. Select the discovery tab. Under target portals, click add. 9. Enter the ip address of...

  • Page 151

    151 10. On the iscsi initiator properties window, select the targets tab. With the iscsi target highlighted, click log on. The log on to target dialogue will appear. 11. If you have not enabled chap, click ok to continue. If you have enabled chap, click advanced. Under advanced settings, check the c...

  • Page 152

    152 12. Right click my computer on the desktop and select manage. 13. Click on disk management and you will see a new hard disk listed. 14. Initialize the new hard disk and you will then be able to use the iscsi target as a local drive..

  • Page 153

    153 windows vista because windows vista has the microsoft iscsi initiator pre-installed, you will not have to install this piece of software. Instead, start the iscsi initiator and follow steps 8-14 to map the thecus ip storage as an iscsi drive. Chapter 6: tips and tricks usb and esata storage expa...

  • Page 154

    154 part i - setup a dyndns account 1. Go to http://www.Dyndns.Org from your home pc. 2. Click on the sign up now link. 3. Check the check boxes, select a user name (i.E.: n8800), enter your email address (i.E.: xxx@example.Com), check enable wildcard, and create a password (i.E.: xxxx). 4. Wait for...

  • Page 155

    155 replacing damaged hard drives if you are using raid 1, raid 5, or raid 6 you can easily replace a damaged hard drive in the thecus ip storage while keeping your data secure with the system’s automatic data recovery. Hard drive damage when a hard drive is damaged and data in the raid volume, the ...

  • Page 156: Chapter 7: Troubleshooting

    156 chapter 7: troubleshooting forgot my network ip address if you forget your network ip address and have no physical access to the system, you can find out the ip address by either looking directly onto thecus ip storage lcd panel, or by using the setup wizard to retrieve the ip of your thecus ip ...

  • Page 157

    157 problems with time and date settings the administrator is able to select an ntp server to keep thecus ip storage time synchronized. However, if thecus ip storage can not access the internet, you may encounter a problem when setting the time and time zone. If this happens: 1. Login to the web adm...

  • Page 158: Thank You For Choosing

    158 appendix a: customer support if your thecus ip storage is not working properly, we encourage you to check out chapter 7: troubleshooting , located in this manual. You can also try to ensure that you are using the latest firmware version for your thecus ip storage. Thecus is committed to providin...

  • Page 159: Appendix B: Raid Basics

    159 appendix b: raid basics overview a redundant array of independent disks (raid) is an array of several hard disks that provide data security and high performance. A raid system accesses several hard disks simultaneously, which improves i/o performance over a single hard disk. Data security is enh...

  • Page 160

    160 this is excellent for complete data security. Raid 5 raid 5 offers data security and it is best suited for networks that perform many small i/o transactions at the same time, as well as applications that require data security such as office automation and online customer service. Use it also for...

  • Page 161

    161 disk usage when all disks are of the same size, and used in raid, thecus ip storage disk usage percentage is listed below: raid level percentage used raid 0 100% raid 1 1/n x 100% raid 5 (n-1)/n x 100% raid 6 (n-2)/n x 100% raid 10 50% jbod 100% n：hdd number.

  • Page 162

    162 appendix c: active directory basics overview with windows 2000, microsoft introduced active directory (ads), which is a large database/information store. Prior to active directory the windows os could not store additional information in its domain database. Active directory also solved the probl...

  • Page 163

    163 appendix d: licensing information overview this product included copyrighted third-party software licensed under the terms of gnu general public license. Please see the gnu general public license for extra terms and conditions of this license. Source code availability thecus technology corp. Has...

  • Page 164

    164 cgic license terms basic license cgic, copyright 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004 by thomas boutell and boutell.Com, inc. Permission is granted to use cgic in any application, commercial or noncommercial, at no cost. However, this copyright paragraph must appear on a "credits...

  • Page 165

    165 they have is not the original, so that any problems introduced by others will not reflect on the original authors' reputations. Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain paten...

  • Page 166

    166 these conditions, and telling the user how to view a copy of this license. (exception: if the program itself is interactive but does not normally print such an announcement, your work based on the program is not required to print an announcement.) these requirements apply to the modified work as...

  • Page 167

    167 4. You may not copy, modify, sublicense, or distribute the program except as expressly provided under this license. Any attempt otherwise to copy, modify, sublicense or distribute the program is void, and will automatically terminate your rights under this license. However, parties who have rece...

  • Page 168

    168 9. The free software foundation may publish revised and/or new versions of the general public license from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing versio...