1. DL manuals
  2. Thermador
  3. Dishwasher
  4. DW1246UB
  5. Installation Instructions Manual

Thermador DW1246UB Installation Instructions Manual

Manual is about: Built-in Dishwasher

Summary of DW1246UB

  • Page 1

    Please read this entire instruction manual before proceeding. Important : local codes vary. Installation, electrical connections, circuit breakers and grounding must comply with all applicable codes. Save these instructions for the local electrical inspector's use. Installer: please leave these inst...

  • Page 2

    Introduction ................................................................................................ 1 tools needed for installation ................................................................ 1 materials you will need ......................................................................

  • Page 3

    Figure 2. Figure 1. O. Cover plugs (2) p. Screws (2), for terminal box cover/toe panel r. Mounting brackets (2) s. Sheet metal screws (2) t. Drain hose clamps (1) u. Screws, m6 x 26 (2) v. Mounting brackets (4) and screws (8) w. Template sheet with instruction pictograms. Tools needed for installati...

  • Page 4

    Dimensions cutout dishwasher overall a height 36” 33-7/8” - 35” (860 - 890 mm) b width 24” 23-9/16” (598 mm) c depth 24” 22-9/16 (573 mm 90 ° 23- 5 / 8 " - 24" (600 - 610 mm) 33- 15 / 16 " (862 mm) minimum 22- 7 / 16 " (570 mm) 90 ° c a 3- 1 /2 " (90mm) 2- 3/8 " (60mm) b attention: pour éviter toute...

  • Page 5

    Hws shut-off valve hot water supply line (520 mm) 20 1/2" warning electrical shock hazard • disconnect electrical power at the circuit breaker box or fuse box before installing the dishwasher. • electrically ground dishwasher. • use copper conductors only. Failure to follow these instructions could ...

  • Page 6

    Mounting bracket bent for mounting to side of cabinet figure 8. 2. Straighten the hot water supply line and the elec- trical cable so that it can be easily pulled through the channel under the dishwasher. See figure 10. 3. Guide the drain hose carefully as the dishwasher is slid into the cabinet ope...

  • Page 7

    Mounting brackets drain hose hot water line electric supply cable air gap entry must be above trap rubber connector min. 20" (500mm) clearance to floor t min. 20" (500 mm) clearance to floor see fig. 2 figure 11. Do not use a drain hose or fittings less than 5/8” i.D. Figure 12. Drain hose if the 7 ...

  • Page 8

    Min. 20" (500 mm) clearance to floor air gap entry must be above trap rubber connector figure 14. 2 1 figure 15. Apply teflon ® tape or other pipe sealant to 90 ° elbow fitting and connect directly to water inlet valve. Attach other end of fitting to your water supply line. When connecting threaded ...

  • Page 9

    Black wires white wires green or bare wires u.L.Listed conduit connector warning electrical shock hazard • disconnect electrical power at the circuit breaker box or fuse box before installing the dishwasher. • electrically ground dishwasher. • use copper conductors only. Failure to follow these inst...

  • Page 10

    25" (636mm) 23-1/16" (586 mm) 1/4" max. (6mm) the remaining pictograms on the template: pictogram 7 on template shows how to adjust the door tension, which is discussed under following section titled door tension adjustment and shown below in figure 20. Pictogram 8 on template shows the fastening of...

  • Page 11

    Door tension adjustment after installation of the dishwasher open and close the door several times. The door should open and close easily with very little force required to lift the door when fully open. If the door closes too quickly, or if the door falls open the spring tension should be adjusted....

  • Page 12

    Specifications are for planning purposes only. Refer to installation instructions and consult your countertop supplier prior to making counter opening. Consult with a heating and ventilating engineer for your specific ventilation requirements. We reserve the right to change specifications or design ...