Thermador GP24WK Installation instructions manual

Other manuals for GP24WK: Care And Use Manual, Service Manual
Manual is about: Professional range series

Summary of GP24WK

  • Page 1

    Installation instructions manual professional cooktops 24" model – gp24wk 36" models – pcs364gd, pcs364gl, pcs366 48" models – pcs484gg, pcs486gd, pcs486gl, pcs484wk important: save these instructions for the local electrical inspector’s use. Installer: please leave these installation instructions w...

  • Page 2

    Page 2 important installation information warning: improper installation, adjustment, alteration, service or main- tenance can cause injury or property damage. Refer to this manual. For assistance or additional information consult a qualified installer, service agency, manufac- turer (dealer) or the...

  • Page 3

    Page 3 step 1: ventilation requirements it is strongly recommended that a suitable exhaust hood be installed above the appliance. Downdraft ventilation should not be used. The table below indicates the thermador hoods, by model number, that are recommended for use with the 24" wok and 36" and 48" co...

  • Page 4

    Page 4 step 2: cabinet preparation 1. To ensure professional results, the cabinet and countertop openings should prepared by a qualified cabinet worker. 2. The clearances shown in fig. 1 are required. The same clear- ances apply to island installa- tions, except for the overhead cabinets, which must...

  • Page 5

    Page 5 step 2: cabinet preparation ∆ as defined in the “national fuel gas code” (ansi z223.1, latest edition). 0" bottom 18" min. 12" both sides 0" sides 24" for 24" wok 36" for 36" cooktop 48" for 48" cooktop **island – 36" for 24" wok island – 48" for 36" cooktop island – 60" for 48" cooktop count...

  • Page 6

    Page 6 3” to center line gas inlet 23-3/8” 2” 1” 26-3/8” 9” 1/2” 12” countertop cabinet face for installation with projecting control panel 3/4” 22-5/8” cabinet face for installation with flush control panel fig. 5 side view of cooktop fig. 9 front - bottom of unit 1/2" close nipple (supplied with u...

  • Page 7

    Page 7 step 3: unpacking, moving, placing & anchoring the cooktop 1. Remove the outer carton and pack- ing material from the shipping base. Ensure that you have all cooktop components before pro- ceeding. 2. Remove the top grate castings, burner caps and grill grate (if so equipped) to reduce unit w...

  • Page 8

    Page 8 step 4: gas requirements & hookup “the appliance must be isolated from the gas supply piping system by closing its individual manual shut- off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (3.5kpa.).” “the appliance and its ...

  • Page 9

    Page 9 step 5: electrical requirements, connection & grounding • always disconnect appliance electric supply cord from wall receptacle before servicing this appliance. • all cooktop models must be plugged into a mating 3-prong, grounding-type receptacle. The receptacle must be connected to a properl...

  • Page 10

    Page 10 step 6: backguard installation a low back backguard must be installed when there is less than a 12" clearance between combustibles and back edge of cooktop. (see fig. 1 and 5.) for island installations and other installations with over 12" clearance, an optional stainless steel trim channel ...

  • Page 11

    Page 11 step 7: test and adjustment caution thermador recommends that burner adjustments be made by a qualified technician at the time of installation. Extreme care should be used when adjustments are made after installation. Improper or lack of adjustments may void your warranty. Install any loose ...

  • Page 12

    Page 12 5551 mcfadden avenue, huntington beach, ca 92649 • 800/735-4328 eco 14028 • 15-12-598d • © 2001 bsh home appliances corp. • litho u. S. A. 4/01 thermador is a leading manufacturer of convection micro thermal ovens, convection thermal ovens, thermal electric ovens, warming drawers, free-stand...