1. DL manuals
  2. Triple S
  3. Floor Machine
  4. Ace 20T
  5. User Manual

Triple S Ace 20T User Manual

Manual is about: Auto Scrubber

Summary of Ace 20T

  • Page 1

    Page 1 of 35 ace 20t auto scrubber the contents of this manual are based on the latest product information available at the time of publication. Triple s reserves the right to make changes or improvements to its machines without notice. Carefully inspect all components to ensure that there is no con...

  • Page 2: Safety Instructions

    Page 2 of 35 safety instructions 1) you must have training in the operation of the machine before using it. Read the instruction book. If you do not understand any instruction, ask your supervisor. 2) make sure all labels, decals, warnings, cautions and instructions are fastened to the machine. 3) r...

  • Page 3

    Page 3 of 35 symbols used on the automatic scrubber water valve indicator brush drive motor control switch vacuum motor control switch brush release switch battery charge indicator main machine power key switch forward – reverse traction drive switch traction drive speed control squeegee lift contro...

  • Page 4: Machine Preparation

    Page 4 of 35 machine preparation 1) unpacking the machine a) take off the outer packaging. B) the machine is fastened to the pallet with wooden wedges that block the wheels. Remove tie down straps. C) disconnect traction motor black lead wire located near the vacuum motor support. D) using a ramp, p...

  • Page 5: Machine Preparation

    Page 5 of 35 machine preparation battery installation (cont.) d) place the batteries in the battery compartment. E) connect the battery connector to the machine connector f) replace the recovery tank and reassemble the vacuum cover and squeegee hose. 3) battery charge level indicator the battery ind...

  • Page 6: Machine Preparation

    Page 6 of 35 machine preparation 4) squeegee assembly installation the squeegee is assembled to the machine by lifting the locking latches and sliding the squeegee assembly onto the 2 posts at the rear of the squeegee swing arm. Push on the locking latches down. Lower the squeegee and install vacuum...

  • Page 7: Machine Preparation

    Page 7 of 35 machine preparation 7) recovery tank open the lid and confirm the following connections are secure: a) the vacuum cover is securely attached. Align the notches and rotate the cover clockwise to close. The vacuum hose must also be attached. B) confirm that the squeegee hose is properly c...

  • Page 8: Machine Operation

    Page 8 of 35 machine operation 1) connect machine connector to the battery connector. 2) turn on the main power key switch. Battery charge indicator will illuminate indicating the charge level of the batteries. If the indicator is flashing the batteries need to be charged. 3) turn on the brush motor...

  • Page 9: Machine Operation

    Page 9 of 35 machine operation 10) machine motion this machine is equipped with traction wheel propulsion. To move machine forward, rock traction directional switch forward and depress the handle switch lever. Adjust the forward speed with the traction drive speed control knob. During the first few ...

  • Page 10

    Page 10 of 35 upon completion of machine use after finishing your work and before any type of maintenance is done, it is necessary to do the following : 1) close the water valve by raising the solution flow control lever. 2) raise the brush base by stepping down locking the brush base lift lever. To...

  • Page 11: Daily Machine Maintenance

    Page 11 of 35 daily machine maintenance cleaning the recovery tank 1) empty the recovery tank by removing the drain plug from the drain hose. Warning: use gloves for protection from contact with dangerous solution. 2) lift the cover of the recovery tank. 3) take off the vacuum cover by rotating it c...

  • Page 12: Daily Machine Maintenance

    Page 12 of 35 daily machine maintenance cleaning the squeegee to obtain the best drying results, keep the squeegee clean. To clean the squeegee it is necessary to: 13) remove the vacuum hose from the squeegee. 14) lift locking latches. Remove the squeegee assembly by pulling rearward. 15) clean the ...

  • Page 13: Daily Machine Maintenance

    Page 13 of 35 daily machine maintenance brush / pad driver removal 24) lift the brush base by depressing the foot level at the rear of the machine. 25) turn on brush motor switch. 26) depress handle switch lever to start the brush spinning. 27) release handle switch lever and quickly depress brush r...

  • Page 14: Weekly Machine Maintenance

    Page 14 of 35 weekly machine maintenance cleaning the squeegee hose to obtain the best drying results, keep the squeegee hose clean. To clean the squeegee hose it is necessary to: 1) take off the vacuum hose from its vacuum port on the squeegee. 2) remove the other end of the vacuum hose from the re...

  • Page 15: Water Solenoid Maintenance

    Page 15 of 35 water solenoid maintenance in the event that the water solenoid begins to leak when turned off debris must be cleared at the valve seat. Water solenoid.

  • Page 16: Trouble Shooting Guide

    Page 16 of 35 trouble shooting guide 1) insufficient water to the brushes a) make sure the solution flow control valve is open. B) confirm that there is water in the solution tank. C) make sure solution dispensing tubes are not clogged or obstructed. 2) the machine does not clean satisfactorily a) c...

  • Page 17

    Page 17 of 35 brush deck assembly drawing 1.

  • Page 18

    Page 18 of 35 drawing 1 part number description & specification qty note 841102 wheel bushing 1 841107 bushing 2 841109 bushing 1 841307 brush deck base weldment 1 epoxy paint 842003 hose clamp 3 ss 842309 base cover 1 843301 fitting barbed 1 843302 fitting barbed 2 843606 splash guard 1 845004 key ...

  • Page 19

    Page 19 of 35 main frame assembly drawing 2.

  • Page 20

    Page 20 of 35 drawing 2 part number description & specification qty note 840307 brush desk lift arm weldment asm 1 840308 brake lever arm weldment 1 840309 brush deck idle arm weldment 1 841106 rubber bushing 2 841108 bushing 2 842003 hose clamp 2 842008 clamp bar 1 842306 pedal cover 1 842311 pedal...

  • Page 21

    Page 21 of 35 squeegee arm assembly drawing 3.

  • Page 22

    Page 22 of 35 drawing 3 part number description & specification qty note 840304 squeegee link arm weldment 1 epoxy paint 840501 squeegee adjuster bolt asm 1 zinc 841103 wheel bushing 2 842405 squeegee lift cable 2 842407 squeegee lift cable 1 845001 adjustment knob 3 845601 squeegee mount base 1 epo...

  • Page 23

    Page 23 of 35 squeegee assembly drawing 4.

  • Page 24

    Page 24 of 35 drawing 4 part number description & specification qty note 840705 squeegee blade front 1 840706 squeegee blade rear 1 841304 squeegee attachment block 2 zinc 842010 band clamp-front 1 ss 842011 band clamp-rear 1 ss 843204 squeegee frame weldment 1 epoxy paint 843312 filler - squeegee 2...

  • Page 25

    Page 25 of 35 solution tank assembly drawing 5.

  • Page 26

    Page 26 of 35 drawing 5 part number description & specification qty note 841300 rear battery bracket 1 zinc 841303 side battery bracket 1 zinc 842003 hose clamp 2 ss 842705 sound deadener 1 843308 fitting barbed 1 843309 fitting barbed 1 843310 filter basket 1 843401 battery plastic gasket 1 843402 ...

  • Page 27

    Page 27 of 35 recovery tank assembly drawing 6.

  • Page 28

    Page 28 of 35 drawing 6 part number description & specification qty note 842007 hose clamp 1 842305 solution tank cover 1 842308 recovery tank cover 1 842403 chain 2 842411 chains for lift 1 843405 tank gasket 1 844101 recovery tank vacuum hose 1 844102 squeegee vacuum hose 1 844103 drain hose 1 845...

  • Page 29

    Page 29 of 35 vacuum assembly drawing 7.

  • Page 30

    Page 30 of 35 drawing 7 part number description & specification qty note 840305 lever arm weldment 1 zinc 840805 bracket-weldment 1 epoxy paint 841104 bushing 2 brass 841305 lever bracket 1 epoxy paint 842014 hose clamp 50mm 1 ss 842702 vacuum motor sound deadener 1 842703 vacuum motor sound deadene...

  • Page 31

    Page 31 of 35 switch box assembly drawing 8.

  • Page 32

    Page 32 of 35 drawing 8 part number description & specification qty note 841306 bezel - rocker switch 5 842301 cover upper switch box 1 842302 cover lower switch box 1 842307 cover - rocker switch 5 842310 cover - small rocker switch 1 843801 grommet 1 844001 fuse holder 1 845101 scrubber lever - sw...

  • Page 33

    Page 33 of 35 electrical schematic drawing 9.

  • Page 34

    Page 34 of 35 drawing 9 part number description & specification qty note 844507 wire harness 1 844509 wire harness 1 844514 wire harness 1 844518 wire harness 1 844519 wire harness 1 844520 wire harness 1 844521 wire harness 1 844522 wire harness 1 844526 wire harness 1 844527 wire harness 1 844530 ...

  • Page 35

    04/2008 page 35 of 35 pn 845672 warranty policy triple s limited warranty the triple s ace 20t has been manufactured, tested and inspected in accordance with specific engineering requirements. This machine is warranted to be free from defects in workmanship and materials for periods as follows from ...