- DL manuals
- Tripp Lite
- Welding System
- APS 1024 INT
- Owner's Manual
Tripp Lite APS 1024 INT Owner's Manual - • Equalize Battery Charge
7
• Equalize Battery Charge
(DIP Switch #3, Group B)
This DIP Switch is momentarily engaged to begin the process of equalizing the internal resistance
of your battery's cells. This can extend the useful life of certain types of batteries; consult with
your battery's manufacturer to determine if your batteries could benefit from this process. The
charge equalization process is automatic and once started can only be stopped by removing the
input power.
• Move to “Equalize” (DOWN) position for three seconds.
• Move to “Reset” (UP) position and leave it there.
Battery Charge
Switch Position
Reset Up*
Equalize Down
* Factory default setting.
• Limit Battery Charger
(DIP Switch #4, Group B)
Your APS has a high powered charger. To prevent it from overheating smaller batteries, its charg-
er is initially set to deliver only a fraction of its maximum power rating to connected batteries. If
you are using it with a larger battery or battery system (over 100 amp-hours), you may switch
your charger to full power without overheating your batteries.
Battery Charger
Switch Position
Partial (
1
/
3
) Charging Power
Up*
Full Charging Power
Down
* Factory default setting.
Configuration
continued
Setting Procedure:
CAUTION: Battery charge equalization should only be performed in
strict accordance with the battery manufacturer’s instructions and
specifications.
CAUTION: Do not leave DIP switch #3 in the down position after
beginning process.
4 3 2 1
Partial*
Full
200201192 UL-Listed APS Manual.qxd 5/17/02 12:41 PM Page 7
Summary of APS 1024 INT
Page 1
Owner’s manual 1111 w. 35th street chicago, il 60609 usa customer support: (773) 869-1234 • www.Tripplite.Com introduction 2 important safety instructions 4 configuration & connection 5 features 11 maintenance and service 14 copyright © 2002 tripp lite. Powerverter ® is a registered trademark of tri...
Page 2: Introduction
2 introduction congratulations! You’ve purchased the most advanced, feature-rich integrated inverter/battery charger on the market. Your aps powers connected equipment, switching manually or automat- ically from utility power to power inverted from an external battery or batteries. In addition to re...
Page 3: 3-Stage Battery Charger
3 3-stage battery charger your aps recharges your battery faster than conventional chargers because its three-stage charger profile (bulk, absorption and float) are optimized, regardless of the type of battery you use (wet or gel).* in addition, the advanced charging system protects against over-cha...
Page 4: Important Safety Instruction
4 important safety instruction save these instructions this manual contains important instructions and warnings that should be followed during the installation, operation and storage of all tripp lite aps systems. Aps location warnings • install your aps indoors, away from excess moisture or heat, d...
Page 5: Configuration
5 configuration dip switch group a battery type / voltage point using a small tool, set the 4 “battery type / voltage point” configuration dip switches, group a (located on the front panel of your aps; see diagram 1, p. 35) to select battery type and set the voltage range outside of which your aps w...
Page 6: Dip Switch Group B
6 dip switch group b load sharing/equalize battery charge the “load sharing” configuration dip switches, #1 and #2 of group b (located on the front panel of your aps; see diagram 1, p. 35), should be set with a small tool according to the guide- lines below. Dip switch #3, group b should be kept in ...
Page 7: • Equalize Battery Charge
7 • equalize battery charge (dip switch #3, group b) this dip switch is momentarily engaged to begin the process of equalizing the internal resistance of your battery's cells. This can extend the useful life of certain types of batteries; consult with your battery's manufacturer to determine if your...
Page 8: Battery Selection
8 battery selection select a battery or system of batteries that will provide your aps with proper dc voltage and an adequate amp hour capacity.* select ‘deep-cycle’ batteries to enjoy optimum performance from your aps. Batteries of either wet-cell (vented) or gel-cell/absorbed glass mat (sealed) co...
Page 9: Battery Connection
9 for ease and safety, tripp lite recommends using tripp lite battery packs with your aps. 1. Make sure that your aps batteries have proper overcurrent protection. Nec article 551 requires that you install a recognized ul component fuse block and ul listed fuse within 18 inches of the battery. The f...
Page 10: Ac Connection
10 aps systems must be connected to a grounded, permanent wiring system. For most installations, the negative battery conductor must be bonded to the grounding system at one (and only one) point in the system. All installations must comply with national and local codes and ordinances. When figuring ...
Page 11: Ac Connection
11 plug the line cord into an outlet providing 120v ac, 60 hz. Power. Make sure that the circuit you connect your aps to has adequate overload protection, such as a circuit breaker or a fuse. Simply plug your equipment into the unit’s ac receptacles. • switch to “auto/remote” when you are using conn...
Page 12: Indicator Lights
12 4. “line” : this green light will turn continuously on whenever connected equipment is receiving utility-supplied ac power and your aps is set to “auto/remote”, meaning that it will automatically switch to battery power if ac power becomes unavailable. It will flash inter- mittently when connecte...
Page 13: Other Features
13 8. Dc power terminals: these terminals should be wired to your battery terminals. See “battery connection”, p. 9 for instructions. 9. Ac receptacles: nema 5-15r (corded models only): these receptacles allow you to connect equipment that would normally be plugged into a utility outlet. They featur...
Page 14: Maintenance & Service
14 your aps model requires no maintenance but should be kept dry at all times. Periodically check all connections both at the unit and at the battery. Clean and tighten connections as necessary. If returning your aps to tripp lite, please pack the aps carefully, using the original packing material t...
Page 15: Troubleshooting
15 try these remedies for common aps problems before calling for help. Call tripp lite customer service at (773) 869-1234 before returning your aps for service. Symptom problems corrections aps does not provide aps not properly connected to connect aps to utility power. Ac output (ac input present) ...
Page 16: Specifications
16 corded models: aps1012ul series number: agap100012mv2 weight: 26.8 lbs. Regulatory approval: ul458 inverter continuous power (@ 20° c): 1000 w surge power (5 seconds): 2000 w efficiency (full load): 88% minimum/maximum dc fuse rating: 150a/300a dc input current @ nominal v dc full load 95 a no lo...
Page 17: Specifications
17 hardwired models: aps2012ul series number: agap200012mv2 weight: 38.8 lbs. Regulatory approval: ul458 inverter continuous power (@ 20° c): 2000 w surge power (5 seconds): 4000 w efficiency (full load): 87% minimum/maximum dc fuse rating: 300a/500a dc input current @ nominal v dc full load 192 a n...
Page 18: Manual Del Propietario
Manual del propietario 1111 w. 35th street chicago, il 60609 ee. Uu. Atención al cliente +1 (773) 869-1234 • www.Tripplite.Com introducción 19 instrucciones de seguridad importantes 21 configuración y conexión 22 características 28 mantenimiento y servicio 31 © 2002 tripp lite. Powerverter ® es una ...
Page 19: Introducción
19 introducción ¡felicitaciones! Usted ha comprado el inversor/cargador de batería integrado más avanzado del mercado, que presenta infinidad de características. El equipo aps proporciona energía al equipo conectado, y puede ser conmutado manual o automáticamente de suministro de energía eléctrica a...
Page 20: Etapas
20 cargadores de batería de tres etapas el aps recarga la batería más rápido que los cargadores convencionales porque su perfil de tres etapas (a granel, absorción y flotación) se optimizan, sin tomar en cuenta el tipo de batería que se use (húmeda o de gel).* el sistema avanzado de carga sirve tamb...
Page 21: Guarde Estas Instrucciones
21 instrucciones de seguridad importantes guarde estas instrucciones este manual contiene advertencias e instrucciones importantes que deben seguirse durante la instalación, operación y almacenaje de todos los sistemas aps de tripp lite. Advertencias sobre la colocación del aps • instale el sistema ...
Page 22: Configuración
22 configuración interruptor dip, grupo a tipo de baterÍa / punto de voltaje use una pequeña herramienta, para colocar en posición los 4 interruptores dip de configuración “tipo de batería / punto de voltaje”, grupo a (ubicados en la parte frontal del panel del aps; refiérase al diagrama 1, en la pá...
Page 23: Configuración
23 configuración continuación 4 3 2 1 puntos limitantes del cargador de batería puntos más limitantes (#1 y #2 up*): los puntos limitantes del cargador tienen efecto en el momento en que se aplica cualquier carga, la salida del cargador baja gradualmente de voltaje de salida total sin carga a ningún...
Page 24: Configuración
24 • carga de batería igualada (interruptor dip #3, grupo b) este interruptor dip se dedica momentáneamente a iniciar el proceso de igualación de la resistencia internade las celdas de su batería. Esto puede ampliar la vida útil de ciertos tipos de baterías; consulte con el fabricante de su batería ...
Page 25: Selección De Las Baterías
25 selección de las baterías seleccione una batería o sistema de baterías que suministrarán al aps el voltaje de cc adecuado y una capacidad de amperios hora adecuada. *seleccione baterías ‘deep-cycle’ para disfrutar de un rendimiento óptimo del aps. Las baterías de fabricación con celdas húmedas (v...
Page 26: Conexión De Las Baterías
26 para facilidad y seguridad, tripp lite recomienda que se utilicen los paquetes de baterías tripp lite con el aps. 1. Confirme que las baterías del aps cuenten con adecuada protección para sobrecargas de corriente. El artículo nec 551 requiere que usted instale un bloque de fusibles de componente ...
Page 27: Conexión De Ca
27 nota: al instalar el aps, la lengüeta principal de conexión a tierra del panel posterior deberá conectarse al chasis del vehículo. Una unidad sin conexión a tierra podría causar riesgo de choque eléctrico. Precaución: nunca opere el aps desde un alternador sin la conexión de una batería tal como ...
Page 28: Conexión De Ca
28 enchufe el cable a una toma de corriente que suministre potencia de 120v de cc, 60 hz. Confirme que el circuito al que se ha conectado el aps cuente con protección de sobrecarga adecuada, tal como un interruptor automático o un fusible. Simplemente enchufe el equipo a los receptáculos de ca de la...
Page 29: Características
29 4. "line” (lÍnea): esta luz verde estará encendida continuamente siempre que el equipo conectado esté recibiendo energía de ca suministrada comercialmente y su aps esté configurado como "auto/remote", lo que significa que automáticamente se cambiará a energía de la batería si la energía de ca no ...
Page 30: Características
30 8. Terminales de energía de dc: estas terminales deben estar cableadas hacia las terminales de su batería. Consulte "conexión de la batería ", pág. 9, si necesita instrucciones. 9. Receptáculos de ca: nema 5-15r (sólo modelos con cable): estos receptáculos permiten conectar el equipo que normalme...
Page 31: Mantenimiento Y Servicio
31 el modelo aps no requiere mantenimiento pero debe conservarse seco en todo momento. Revise periódicamente todas las conexiones tanto en la unidad como en la batería. Limpie y ajuste las conexiones según sea necesario. En caso de devolución del aps a tripp lite, sírvase embalarlo con cuidado, usan...
Page 32: Solución De Problemas
Pruebe estas soluciones para los problemas comunes del aps antes de llamar para solicitar ayuda. Llame al departamento de servicios al cliente de tripp lite al (773) 869-1234 antes de devolver el aps para servicio. SÍntoma problemas correcciÓn aps no proporciona salida de el aps no está adecuadament...
Page 33: Ficha Técnica
33 modelos con cable: aps1012ul número de serie: agap100012mv2 peso: 26.8 libras aprobación reglamentaria: ul458 inversor potencia continua (@ 20° c): 1000 w corriente de sobretensión (5 segundos): 2000 w eficacia (carga completa): 88% tasa mínima/máxima de fusible de cc: 150a/300a corriente de entr...
Page 34: Ficha Técnica
34 modelos con conexiÓn directa al circuito: aps2012ul número de serie: agap200012mv2 peso: 38.0 libras aprobación reglamentaria: ul458 inversor potencia continua (@ 20° c): 2000 w energía de sobretensión (5 segundos): 4000 w eficacia (carga completa): 87% tasa mínima/máxima de fusible de cc: 300a/5...
Page 35: Diagramas/esquemas
18 35 hot in neutral in ground in ground out hot out “for use with copper wire only” neutral out diagramas/esquemas see “configuration”, pg. 5. 1.1 is dip switch group a. 1.2 is dip switch group b. Refiérase a la sección “configuración”, pg. 22. 1.1 representa el interruptor dip, grupo a. 1.2 repres...
Page 36: Diagramas/esquemas
36 x/2 volts x/2 volts aps see battery connection, pg. 9. 5.1 is the fuse. X = your aps’s inverter's nominal input voltage. (see specs.) refiérase a la sección conexión de baterías, pág. 26. 5.1 representa el fusible. X = voltaje nominal de entrada del inversor del aps. (refiérase a la ficha técnica...
Page 37: Diagramas/esquemas
20 37 aps 12v 12v basic 12vdc vehicular battery connection. See pg. 9. 8.1 is the alternator. 8.2 is the vehicle battery ground. 8.3 is the vehicle battery. 8.4 is the fuse. Conexión básica avanzada de batería vehicular de 12vcc. Refiérase a la pág. 26. 8.1 representa el alternador. 8.2 representa l...
Page 38: Diagramas/esquemas
38 1. Operating mode switch 2. Dip switch group a 3. Dip switch group b 4. “line” 5. “inv” (inverting) 6. “load” 7. “battery hi/med/lo” 8. Dc input terminals 9. Ac receptacles (corded models only) 10. Fixed ac input line cord fixed (corded models only) 12. Resettable circuit breakers 13. Remote modu...
Page 39: Diagramas/esquemas
Hot in neutral in ground in ground out hot out “for use with copper wire only” neutral out diagramas/esquemas 10b 1. Operating mode switch 2. Dip switch group a 3. Dip switch group b 4. “line” 5. “inv” (inverting) 6. “load” 7. “battery hi/med/lo” 8. Dc input connector 11. Ac input/output terminal st...
Page 40
93-2035 (200201192) 40 200201192 ul-listed aps manual- trans..Qxd 5/17/02 12:40 pm page 23.