- DL manuals
- U-Line
- Refrigerator
- 1215R
- User manual
U-Line 1215R User manual - page 14
USER GUIDE
Integrated Panel Installation 1
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Integrated Panel Installation
1. Fully open door/drawer.
2. Starting at corner, pull
gasket away from door/
drawer.
3. Continue to pull gasket
free from gasket channel.
4. Upon removal, lay gasket down on a flat surface.
5. The panel should be aligned with the outside edge
(opposite the hinge) and high enough to align with the
highest point in the door/drawer.
NOTICE
Due to differences in floor construction or
surrounding cabinetry, the panel may not sit
flush with the top of the door/drawer.
6. Secure integrated
panel to door/drawer
using clamps. A
robust tape may also
be used. U-Line
recommends the use
of bar clamps to
secure the panel to
the door/drawer. If
using tape, be
certain the tape will
not damage panel
finish upon removal.
7. Using a 7/64" (3 mm)
drill bit, drill 6 pilot
holes into the wood
panel 1/2" (12 mm)
deep using the holes in the door/drawer frame as a
guide.
NOTICE
It is important to ensure that all drilled holes are
drilled to the correct depth in order to avoid
splits in the wood when hardwood is installed.
8. Locate 6 of the #6x 1-1/4" (32 mm) screws provided
with your unit.
9. Using a Phillips screwdriver, place one screw into each
of the 6 pilot holes and screw down. Do not overtighten
screws.
10.Be sure the screws force their way past the opening on
the gasket channel and sit flush against the bottom of
the channel.
Align Panel
Against
Door/Drawer
Edge First
Align Top Of Panel With Highest Point Of Door/Drawer
Door
Panel
Wood
Panel
Door/Drawer
Bar
Clamp
Bar
Clamp
Integrated Panel
Integrated Panel
Summary of 1215R
Page 1
User guide safety • installation & integration • operating instructions • maintenance • service 1000 series • 1224r • 24" solid door refrigerator right product. Right place. Right temperature. Since 1962..
Page 2
User guide u-line.Com contents safety • installation & integration • operating instructions • maintenance • service intro safety safety and warning disposal and recycling installation environmental requirements electrical cutout dimensions product dimensions side by side installation anti-tip bracke...
Page 3
User guide introduction 1 u-line.Com welcome to u-line congratulations on your u-line purchase. Your product comes from a company with over five decades and three generations of premium modular ice making, refrigeration, and wine preservation experience. U-line continues to be the american leader, d...
Page 4
User guide safety and warning 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service safety and warning notice please read all instructions before installing, operating, or servicing the appliance. Use this appliance for its intended purpose only and follow...
Page 5
User guide disposal and recycling 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service disposal and recycling danger ! Risk of child entrapment. Before you throw away your old refrigerator or freezer, take off the doors and leave shelves in place so child...
Page 6
User guide environmental requirements 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service environmental requirements this model is intended for indoor/interior applications only and is not to be used in installations that are open/ exposed to natural ele...
Page 7
User guide electrical 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service electrical warning ! Shock hazard — electrical grounding required. Never attempt to repair or perform maintenance on the unit until the electricity has been disconnected. Never rem...
Page 8
User guide cutout dimensions 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service cutout dimensions prepare site your u-line product has been designed for either free- standing or built-in installation. When built-in, your unit does not require additional...
Page 9
User guide product dimensions 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service product dimensions 3-9/16" (91 mm) 34-1/8" to 35-1/8" (867 mm to 892 mm) 23-1/4" (591 mm) (includes 3/4" [20 mm] integrated panel) 24" (610 mm).
Page 10
User guide side-by-side installation 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service side-by-side installation two units may be installed side-by-side. Cutout width for a side-by-side installation is the cutout dimension of a single unit times two. N...
Page 11
User guide anti-tip bracket 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service anti-tip bracket 1. Slide unit out so screws on top of unit are easily accessible. 2. Remove the two screws from the opposite side of the hinge assembly using a t-25 torx dri...
Page 12
User guide general installation 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service general installation leveling information 1. Use a level to confirm the unit is level. Level should be placed along top edge and side edge as shown. 2. If the unit is not...
Page 13
User guide integrated panel dimensions 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service integrated panel dimensions integrated panel notice due to differences in surrounding cabinetry the panel may not perfectly align with door. The procedure below is...
Page 14
User guide integrated panel installation 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service integrated panel installation 1. Fully open door/drawer. 2. Starting at corner, pull gasket away from door/ drawer. 3. Continue to pull gasket free from gasket c...
Page 15
User guide integrated panel installation 2 u-line.Com safety • installation & integration • operating instructions • maintenance • service 11.Remove clamps from door/drawer. Notice if panel requires additional adjustment after removing clamps, slightly loosen each screw and adjust panel as necessary...
Page 16
User guide grille - plinth installation 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service grille - plinth installation removing and installing grille warning ! Disconnect electric power to the unit before removing the grille. When using the unit, the g...
Page 17
User guide door swing 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service door swing units have a zero clearance for the door to open 90°, when installed adjacent to cabinets. Stainless steel and black and white models require 2-1/8" (54 mm) door clearan...
Page 18
User guide door stop 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service door stop your u-line unit was shipped to you with the optional 90° pin(s). (models that are 15" wide include 1 pin. Models that are 24" wide include 2 pins.) the unit’s door will o...
Page 19
User guide door adjustments 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service door adjustments door alignment and adjustment align and adjust the door if it is not level or is not sealing properly. If the door is not sealed, the unit may not cool prope...
Page 20
User guide door adjustments 2 u-line.Com safety • installation & integration • operating instructions • maintenance • service 3. Remove bottom hinge from cabinet by removing three screws. Support the door and hinge assembly and remove it from the cabinet. 4. Remove four screws from hinge holes on th...
Page 21
User guide free standing kit 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service free standing kit the free standing kit is an optional accessory. It is only used when unit is not installed in surrounding cabinetry. To install the kit: 1. Remove grille (...
Page 22
User guide first use 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service first use all u-line controls are preset at the factory. Initial startup requires no adjustments. Notice u-line recommends allowing the unit to run overnight before loading with pro...
Page 23
User guide control operation 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service control operation door alert notification when the door is left open for more than 5 minutes: • an audible tone will sound for several seconds every minute. • the alert led ...
Page 24
User guide sabbath mode 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service l sabbath mode this unit is star-k certified and offers a sabbath mode. Sabbath mode disables system responses to user initiated activities and all external functions, including ...
Page 25
User guide airflow and product loading 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service airflow and product loading notice the unit requires proper airflow to perform at its highest efficiency. Do not block the front grille, or the unit will not perfo...
Page 26
User guide interior shelves 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service interior shelves removing and installing interior shelves for models equipped with glass shelves having recessed shelf supports, remove the shelves as follows: 1. Pull shelf ...
Page 27
User guide cleaning 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service cleaning exterior cleaning vinyl clad (black or white) clean surfaces with a mild detergent and warm water solution. Do not use solvent-based or abrasive cleaners. Use a soft sponge ...
Page 28
User guide cleaning 2 u-line.Com safety • installation & integration • operating instructions • maintenance • service high ambient temperature and excessive humidity can also produce frost. Caution ! Do not use an ice pick or other sharp instrument to help speed up defrosting. These instruments can ...
Page 29
User guide cleaning condenser 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service cleaning condenser interval - every six months to maintain operational efficiency, keep the front grille free of dust and lint, and clean the condenser when necessary. Depe...
Page 30
User guide extended non-use 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service extended non-use vacation/holiday, prolonged shutdown the following steps are recommended for periods of extended non-use: 1. Remove all consumable content from the unit. 2. ...
Page 31
User guide troubleshooting 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service troubleshooting before calling for service if you think your u-line product is malfunctioning, read the control operation section to clearly understand the function of the con...
Page 32
User guide troubleshooting 2 u-line.Com safety • installation & integration • operating instructions • maintenance • service checking product temperature to check the actual product temperature in the unit: 1. Partially fill a plastic (nonbreakable) bottle with water. 2. Insert an accurate thermomet...
Page 33
User guide warranty 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service warranty u-line corporation limited warranty 1. U-line corporation (“u-line”) warrants each u-line product to be free from defects in materials and workmanship for a period of one ye...
Page 34
User guide warranty 2 u-line.Com safety • installation & integration • operating instructions • maintenance • service of pool water, or directing a spray from a hose or similar device into and around the unit. 7. If a product defect is discovered during the applicable warranty period, you must promp...
Page 35
User guide wire diagram 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service wire diagram 42313_b wiring diagram 120 volt plug neutral hot relay embraco compressor green or green w/ yellow ground: overload cap 1 10 control board fuse 16 8 9 1 6 1 10 5 tes...
Page 36
User guide product liability 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service product liability important note: service or repairs must not be performed on any unit suspected to be involved in a property damage situation. If a unit has been altered or...
Page 37
User guide warranty claims 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service warranty claims the following information defines the parameters for filing a warranty claim: • valid serial number needed • valid model number needed • narda (or equivalent) ...
Page 38
User guide ordering replacement parts 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service ordering replacement parts parts may be ordered on-line, by fax or on the phone. See our contact information below: www.U-lineservice.Com (with service login) fax n...
Page 39
User guide system diagnosis guide 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service system diagnosis guide refrigeration system diagnosis guide system condition suction pressure suction line compressor discharge condenser capillary tube evaporator watt...
Page 40
User guide compressor specifications 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service compressor specifications danger ! Electrocution can cause death or serious injury. Burns from hot or cold surfaces can cause serious injury. Take precautions when s...
Page 41
User guide troubleshooting - extended 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service troubleshooting - extended specific errors and issues the technically advanced diagnostic capabilities of the electronic controls utilized on the 1200 and 2200 seri...
Page 42
User guide troubleshooting - extended 2 u-line.Com safety • installation & integration • operating instructions • maintenance • service refrigeration system diagnosis guide errors *all errors are logged in memory. *only door error is displayed on the display and has an audible signal. *for clear ice...
Page 43
User guide troubleshooting - extended 3 u-line.Com safety • installation & integration • operating instructions • maintenance • service testing the main control if the main control is suspected of being faulty, the following procedure should be performed to verify main control for functionality. Rel...
Page 44
User guide troubleshooting - extended 4 u-line.Com safety • installation & integration • operating instructions • maintenance • service thermistor failure zone thermistor if the zone thermistor fails, the unit will continue to operate in a timed limp mode which varies by model. The unit will otherwi...
Page 45
User guide control operation - service 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service control operation - service ui button layout 1. Hidden button -accesses service menu -no led 2. Up button -increases temperature -navigates through service menu 3....
Page 46
User guide control operation - service 2 u-line.Com safety • installation & integration • operating instructions • maintenance • service 1. Viewing actual temperature in viewing temperature in these modes any offsets are taken into account. This means that if you place a thermistor in a known temper...
Page 47
User guide control operation - service 3 u-line.Com safety • installation & integration • operating instructions • maintenance • service service mode guide number service mode menu item to navigate/access 1 view thermistor #1 cabinet temp no offsets use up/down to access and light bulb key to view 2...
Page 48
User guide control operation - service 4 u-line.Com safety • installation & integration • operating instructions • maintenance • service service mode guide 1. Thermistor 1 — temperature this will show the pure thermistor reading with no offsets taken into account. When placed in ice water this therm...
Page 49
User guide control operation - service 5 u-line.Com safety • installation & integration • operating instructions • maintenance • service 19. Individual component toggle relay #2. ... Relay #3. Will start the ice maker module and forward it through a full harvest cycle relay #4. Will send voltage to ...
Page 50
User guide control defaults 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service control defaults * 115v models default to fahrenheit. 220-240v models default to celsius. ** offset and differential always expressed in °f. Default value fahrenheit/celsius*...
Page 51
User guide service mode 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service service mode service mode quick guide number service mode menu item to navigate/access 1 view thermistor #1 cabinet temp no offsets use up/down to access and light bulb key to vi...
Page 52
User guide service mode 2 u-line.Com safety • installation & integration • operating instructions • maintenance • service errors *all errors are logged in memory. *only door error is displayed on the display and has an audible signal. *for 68118 models, pump error is displayed via alert light with n...
Page 53
User guide thermistor 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service thermistors thermistors are used for various temperature readings. Thermistors provide reliable temperature readings using a resistance which varies based on surrounding temperatur...
Page 54
User guide defrost 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service defrost these units are automatic (cycle) defrost unit will defrost itself when the control/sensor is satisfied of internal temperatures. Defrost mode ends when control/sensor asks fo...