- DL manuals
- U-Line
- Refrigerator
- 2075
- User Manual
U-Line 2075 User Manual
Summary of 2075
Page 1
P . O . B o x 2 4 5 0 4 0 milwaukee, wi 53224-9540 p h o n e : 4 1 4 . 3 5 4 . 0 3 0 0 f a x : 4 1 4 . 3 5 4 . 7 9 0 5 w w w . U - l i n e . C o m p r i n t e d i n u . S . A . P / n 3 0 0 0 1 É c h e l o n ™ u s e r m a n u a l.
Page 2
U-line corporation limited warranty u-line corporation warrants each u-line product to be free from defects in materials and workmanship for a period of one year from the date of purchase; and warrants the sealed system (consisting of the compressor, the condenser, the evaporator, the hot gas bypass...
Page 3
Introduction congratulations on your purchase of the u-line 2075dwrr drawer unit. A pioneer in the field for more than 40 years, u-line is the world’s number one manufacturer of built-in, under-counter ice making and spe- cialty refrigeration products. U-line dedicates 100% of its research and devel...
Page 4
If you do not return your product registration card, u-line will use the date of sale to the u-line distributor as the first date of warranty for your unit. Please also record the purchase date of your u- line unit and your dealer’s name, address and telephone number. Model number: _________________...
Page 5
Safety precautions do not attempt to install or operate your unit until you have read the safe- ty precautions in this manual. Safety items throughout this manual are labeled with a danger, warning or caution based on the risk type. Definitions danger means that failure to follow this safety stateme...
Page 6
General precautions risk of child entrapment. Before you throw away your old refrigerator or freezer, take off the doors and leave shelves in place so that children may not easily climb inside. • never attempt to repair or perform maintenance on the unit until the electricity has been disconnected. ...
Page 7
Installation site preparation your u-line drawer unit must be installed under a counter or in a wall. The unit is designed so it can be installed next to a wall, because the crisper can be accessed from either side. 1. Position the unit on a flat, level surface, capable of supporting the entire weig...
Page 8
Your u-line drawer unit is designed so it can be installed next to the wall on either side because the crisper can be accessed from either side (figure 1, 2). Figure 1 – right wall installation the anti-tip kit must be installed on this unit before it is used. Never use the drawers as steps or a she...
Page 9
Figure 2 – left wall installation figure 3 – front clearance dwr003 24" min. Cabinet or wall dwr002 7.
Page 10
4. Position the unit to allow free air flow through the front grille (figure 4). Figure 4 leveling the unit it is important that the unit is level. All Échelon™ series units are equipped with adjustable feet for leveling and height adjustment (figure 5). To level the unit: 1. Adjust all four levelin...
Page 11
4. Place the unit in position where it is to be installed. Re-check cabi- net height and levelness (figure 6) and adjust if necessary. Figure 5 figure 6 dwr021 level two places dwr005 raise lower 9.
Page 12
10 user’s manual built-in installation your u-line product is designed for built-in installation only. When built-in, it does not require additional air space for the top, sides, or rear. However, the front grille must not be obstructed. Note to ease unit installation and removal, it is recommended ...
Page 13
Figure 7 custom drawer panels two types of custom drawer panels can be installed on your u-line unit to harmonize with or accent the surrounding decor. Full overlay drawer panel full overlay drawer panels completely cover the drawer frames and han- dle to give a built-in appearance. See table 1 for ...
Page 14
Overlay panel kit parts • the total weight of both drawer panels must not weigh more than 20 lbs. • the thickness of the drawer panel must be 3/4". Remove existing drawer front from cabinet: 1. Open drawer. Pull door gasket (figure 8) out of the groove (top edge of door only). Start in the mid- dle ...
Page 15
13 5. On a clean surface, place the wood panel face down and tape the existing drawer panel (removed in step 3) on the back of the wood panel (figure 10) and drill the five (5) holes (5/32" drill 3/8" deep) through the coated steel panel and 3/8" into the wood panel according to the diagram (figure ...
Page 16
User’s manual 14 6. Attach the drawer panel to the wood panel using #10 x 5/8" (p/n 42121) wood screws and nylon spacers (p/n 42120). The nylon spacers fit between the wood panel and the drawer panel as shown (figure 12). Figure 12 drawer panel and wood panel must be aligned properly or drawer will ...
Page 17
15 custom insert drawer panel custom drawer panels can be inserted into the drawer frames to match the surrounding decor. Custom drawer panels can be flat or raised, as long as the maximum panel thickness where inserted into the drawer reveal (channel) is 1/4" thick. For raised panels, the depth of ...
Page 18
Install the custom insert as follows: insert edges may be sharp! Use care when installing. 1. Open drawer. Pull drawer gas- ket out of groove (top edge of drawer only). Start in the mid- dle and pull outward, moving toward the edge (figure 14). This may take some force, be careful. 2. Remove the thr...
Page 19
5. Slide custom drawer panel insert into 1/4" channel in drawer front. 6. Attach the full handle to the lower handle using the 3 screws removed in step 2. 7. Holding drawer gasket out of the way, replace handle on drawer making sure it is seated properly on insert and that screw holes line up. 8. In...
Page 20
18 user’s manual temperature controller figure 17 the temperature controller (figure 17) is located in the top drawer. It consists of an led display, two led status indicator lights and three touch pad buttons. The led display shows the temperature set point and is calibrated in degrees fahrenheit. ...
Page 21
19 drawers the drawers should only be removed for servicing by a trained and certified repair person. Top storage bin grasp the bin handle and slide back- ward to access the contents below (figure 18). The bin may be completely removed for cleaning once it clears the guides on each side of the drawe...
Page 22
20 user’s manual operation drawer organizer adjust the drawer organizer to compensate for different size bottles or items. The organizer can be used in either drawer, but is shipped from the factory in the top drawer. The organizer may be adjusted left-to-right or front-to-back as required. When adj...
Page 23
21 be sure that items stored in the rear of the top drawer do not interfere with the sliding operation of the stor- age bin (figure 21). Tall items such as milk jugs can be stored toward the front of the drawer as long as they do not interfere with the closing of the drawer. Taller items can be stor...
Page 24
Light bulb replacement light bulb replacement in the Échelon™ series is simple. 1. Remove the light housing cover by sliding the cover toward the tab, swinging the end opposite the tab down and pulling down and away (figure 22). 2. Replace bulb with genuine u-line #31317 replacement. U-line p/n 3131...
Page 25
23 cleaning & maintenance periodic cleaning and proper maintenance will ensure efficiency, top per- formance, and long life. The maintenance intervals listed are based on normal conditions. You may want to shorten the intervals if you have pets, the unit is used outdoors, or other special considerat...
Page 26
24 user’s manual 5. Reconnect power to the unit. • do not use solvent cleaning agents or abrasives on the interior. These cleansers may damage or discolor the interior. Condenser cleaning - every 3 months disconnect electric power to the unit before cleaning the condenser. To remove and replace the ...
Page 27
25 do not touch the condenser fins. The condenser fins are sharp and can be easily damaged. 3. Clean the condenser coil using a soft brush with a “combing” action or vacuum cleaner. Do not touch the condenser coil. 4. Position the grille to align the screw holes with the cabinet. 5. Insert the grill...
Page 28
26 user’s manual troubleshooting before calling for service if the unit appears to be malfunctioning, read through normal opera- tion first. If the problem persists, check the troubleshooting guide. Locate the problem in the guide and refer to the cause and its remedy before calling for service. The...
Page 29
27 problem possible cause remedy the unit is not temperature not set set temperature controller to cold enough cold enough. Colder setting. See page 18. (continued) allow 24 hours for temperature to stabilize. Noise during certain sounds soft sounds from the operation. Are normal. Compressor and fan...
Page 30
28 user’s manual.
Page 31
P . O . B o x 2 4 5 0 4 0 milwaukee, wi 53224-9540 p h o n e : 4 1 4 . 3 5 4 . 0 3 0 0 f a x : 4 1 4 . 3 5 4 . 7 9 0 5 w w w . U - l i n e . C o m p r i n t e d i n u . S . A . P / n 3 0 0 0 1 ( r e v . 5 / 0 3 ) É c h e l o n ™ u s e r m a n u a l.