- DL manuals
- U-Line
- Refrigerator
- ADA24R
- User Manual
U-Line ADA24R User Manual - page 8
USER GUIDE
Cutout Dimensions 1
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Cutout Dimensions
PREPARE SITE
Your U-Line product has been designed for either free-
standing or built-in installation. When built-in, your unit
does not require additional air space for top, sides, or
rear. However, the front grille must NOT be obstructed,
and clearance is required for an electrical connection in
the rear.
CAUTION
!
Unit can NOT be installed behind a closed cabinet
door.
CUTOUT DIMENSIONS
4"
(102 mm)
7"
(178 mm)
24"
(610 mm)
24-1/4"
(616 mm)
32"
(813 mm)
to
33"
(838 mm)
Preferred location
for electrical
outlet is in
adjacent
cabinet.
5/8"
(16 mm)
Summary of ADA24R
Page 1
User guide safety • installation & integration • operating instructions • maintenance • service ada series • ada24r • 24" solid door refrigerator right product. Right place. Right temperature. Since 1962..
Page 2
User guide u-line.Com contents safety • installation & integration • operating instructions • maintenance • service intro safety safety and warning disposal and recycling installation environmental requirements electrical cutout dimensions product dimensions side by side installation anti-tip bracke...
Page 3
User guide introduction 1 u-line.Com welcome to u-line congratulations on your u-line purchase. Your product comes from a company with over five decades and three generations of premium modular ice making, refrigeration, and wine preservation experience. U-line continues to be the american leader, d...
Page 4
User guide safety and warning 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service safety and warning notice please read all instructions before installing, operating, or servicing the appliance. Use this appliance for its intended purpose only and follow...
Page 5
User guide disposal and recycling 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service disposal and recycling danger ! Risk of child entrapment. Before you throw away your old refrigerator or freezer, take off the doors and leave shelves in place so child...
Page 6
User guide environmental requirements 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service environmental requirements this model is intended for indoor/interior applications only and is not to be used in installations that are open/ exposed to natural ele...
Page 7
User guide electrical 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service electrical warning ! Shock hazard — electrical grounding required. Never attempt to repair or perform maintenance on the unit until the electricity has been disconnected. Never rem...
Page 8
User guide cutout dimensions 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service cutout dimensions prepare site your u-line product has been designed for either free- standing or built-in installation. When built-in, your unit does not require additional...
Page 9
User guide product dimensions 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service product dimensions 23-1/4 " (591 mm) 32 " to 33” (813 mm 838 mm) 24 " (610 mm) not including handle.
Page 10
User guide side-by-side installation 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service side-by-side installation two units may be installed side-by-side. Cutout width for a side-by-side installation is the cutout dimension of a single unit times two. N...
Page 11
User guide anti-tip bracket 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service anti-tip bracket 1. Slide unit out so screws on top of unit are easily accessible. 2. Remove the two screws from the opposite side of the hinge assembly using a t-25 torx dri...
Page 12
User guide general installation 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service general installation leveling information 1. Use a level to confirm the unit is level. Level should be placed along top edge and side edge as shown. 2. If the unit is not...
Page 13
User guide grille - plinth installation 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service grille - plinth installation removing and installing grille warning ! Disconnect electric power to the unit before removing the grille. When using the unit, the g...
Page 14
User guide door swing 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service door swing units have a zero clearance for the door to open 90°, when installed adjacent to cabinets. Stainless steel and black and white models require 2-1/8" (54 mm) door clearan...
Page 15
User guide door stop 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service door stop your u-line unit was shipped to you with the optional 90° pin(s). (models that are 15" wide include 1 pin. Models that are 24" wide include 2 pins.) the unit’s door will o...
Page 16
User guide door adjustments 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service door adjustments door alignment and adjustment align and adjust the door if it is not level or is not sealing properly. If the door is not sealed, the unit may not cool prope...
Page 17
User guide door adjustments 2 u-line.Com safety • installation & integration • operating instructions • maintenance • service 3. Remove bottom hinge from cabinet by removing three screws. Support the door and hinge assembly and remove it from the cabinet. 4. Remove four screws from hinge holes on th...
Page 18
User guide first use 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service first use all u-line controls are preset at the factory. Initial startup requires no adjustments. Notice u-line recommends allowing the unit to run overnight before loading with pro...
Page 19
User guide control operation 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service control operation door alert notification when the door is left open for more than 5 minutes: • an audible tone will sound for several seconds every minute. • the alert led ...
Page 20
User guide sabbath mode 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service l sabbath mode this unit is star-k certified and offers a sabbath mode. Sabbath mode disables system responses to user initiated activities and all external functions, including ...
Page 21
User guide airflow and product loading 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service airflow and product loading notice the unit requires proper airflow to perform at its highest efficiency. Do not block the front grille, internal fans or vents at ...
Page 22
User guide interior shelves 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service interior shelves wire shelf removal and installation for ada models equipped with wire racks, reposition the shelves as follows: 1. Remove shelf retention clip. 2. Pull shelf...
Page 23
User guide cleaning 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service cleaning exterior cleaning vinyl clad (black or white) clean surfaces with a mild detergent and warm water solution. Do not use solvent-based or abrasive cleaners. Use a soft sponge ...
Page 24
User guide cleaning 2 u-line.Com safety • installation & integration • operating instructions • maintenance • service high ambient temperature and excessive humidity can also produce frost. Caution ! Do not use an ice pick or other sharp instrument to help speed up defrosting. These instruments can ...
Page 25
User guide cleaning condenser 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service cleaning condenser interval - every six months to maintain operational efficiency, keep the front grille free of dust and lint, and clean the condenser when necessary. Depe...
Page 26
User guide extended non-use 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service extended non-use vacation/holiday, prolonged shutdown the following steps are recommended for periods of extended non-use: 1. Remove all consumable content from the unit. 2. ...
Page 27
User guide troubleshooting 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service troubleshooting before calling for service if you think your u-line product is malfunctioning, read the control operation section to clearly understand the function of the con...
Page 28
User guide troubleshooting 2 u-line.Com safety • installation & integration • operating instructions • maintenance • service checking product temperature to check the actual product temperature in the unit: 1. Partially fill a plastic (nonbreakable) bottle with water. 2. Insert an accurate thermomet...
Page 29
User guide warranty 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service warranty u-line corporation limited warranty 1. U-line corporation (“u-line”) warrants each u-line product to be free from defects in materials and workmanship for a period of one ye...
Page 30
User guide warranty 2 u-line.Com safety • installation & integration • operating instructions • maintenance • service of pool water, or directing a spray from a hose or similar device into and around the unit. 7. If a product defect is discovered during the applicable warranty period, you must promp...
Page 31
User guide wire diagram 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service wire diagram 42313_b wiring diagram 120 volt plug neutral hot relay embraco compressor green or green w/ yellow ground: overload cap 1 10 control board fuse 16 8 9 1 6 1 10 5 tes...
Page 32
User guide product liability 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service product liability important note: service or repairs must not be performed on any unit suspected to be involved in a property damage situation. If a unit has been altered or...
Page 33
User guide warranty claims 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service warranty claims the following information defines the parameters for filing a warranty claim: • valid serial number needed • valid model number needed • narda (or equivalent) ...
Page 34
User guide ordering replacement parts 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service ordering replacement parts parts may be ordered on-line, by fax or on the phone. See our contact information below: www.U-lineservice.Com (with service login) fax n...
Page 35
User guide system diagnosis guide 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service system diagnosis guide refrigeration system diagnosis guide system condition suction pressure suction line compressor discharge condenser capillary tube evaporator watt...
Page 36
User guide compressor specifications 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service compressor specifications danger ! Electrocution can cause death or serious injury. Burns from hot or cold surfaces can cause serious injury. Take precautions when s...
Page 37
User guide troubleshooting - extended 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service troubleshooting - extended specific errors & issues caution ! Never attempt to repair or perform maintenance on the unit until the main electrical power has been di...
Page 38
User guide troubleshooting - extended 2 u-line.Com safety • installation & integration • operating instructions • maintenance • service ice maker diagnosis flow chart does the unit refrigerate? Sealed system leak electrical failure compressor failure fan motor failure defrost system failure low volt...
Page 39
User guide troubleshooting - extended 3 u-line.Com safety • installation & integration • operating instructions • maintenance • service product temperature causes which affect the internal temperatures of the cabinet include: • temperature setting. • ambient temperature where installed. • installati...
Page 40
User guide troubleshooting - extended 4 u-line.Com safety • installation & integration • operating instructions • maintenance • service refrigeration system diagnosis guide ice maker operating cycles freeze cycle temperature control terminals 2 and 3 are closed. Power to the compressor. Power to the...
Page 41
User guide troubleshooting - extended 5 u-line.Com safety • installation & integration • operating instructions • maintenance • service harvest-1 cycle temperature control terminals 2 and 3 are open - 2 and 1 close. No power to the compressor or condenser fan. If bin arm is down, power goes through ...
Page 42
User guide troubleshooting - extended 6 u-line.Com safety • installation & integration • operating instructions • maintenance • service harvest-2 cycle ice maker ejector blades reach approximately 2:00 position and cam depresses the hold switch. Power goes through the hold switch to the ice maker mo...
Page 43
User guide troubleshooting - extended 7 u-line.Com safety • installation & integration • operating instructions • maintenance • service water fill cycle ice maker ejector blades reach approximately 10:00 position and cam depresses the water fill switch. Power to the water valve. Ice maker mold fills...
Page 44
User guide troubleshooting - extended 8 u-line.Com safety • installation & integration • operating instructions • maintenance • service temperature control specifications these temperature controls are double throw, single pole controls. The sensing tube is inserted into the ice maker mold and sense...
Page 45
User guide troubleshooting - extended 9 u-line.Com safety • installation & integration • operating instructions • maintenance • service limit switch specifications normally closed bi-metal switch open temperature: 104°f close temperature: 83°f the function of this switch is to open in the event of a...
Page 46
User guide troubleshooting - extended 10 u-line.Com safety • installation & integration • operating instructions • maintenance • service frost free refrigeration cooling mode bypass solenoid closed. Evaporator fan operating. Refrigerant flows through capillary tubes. Normal vapor/compression cycle r...
Page 47
User guide troubleshooting - extended 11 u-line.Com safety • installation & integration • operating instructions • maintenance • service air flow in at evaporator blade air flow out at evaporator outlet air passes though fin tube evaporator condensate drains down past the evaporator, into drain pan,...
Page 48
User guide control operation - service 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service control operation - service ui button layout 1. Hidden button: -accesses service menu -no led 2. Up button -increases temperature -navigates through service menu 3...
Page 49
User guide control operation - service 2 u-line.Com safety • installation & integration • operating instructions • maintenance • service electronic control descriptions quick guide except as noted, these functions are available on all models. 1. On/off the on/off mode allows the unit to be turned on...
Page 50
User guide control operation - service 3 u-line.Com safety • installation & integration • operating instructions • maintenance • service service mode quick guide number service mode menu item to navigate/access 1 view thermistor #1 cabinet temp no offsets use up/down to access and light bulb key to ...
Page 51
User guide control operation - service 4 u-line.Com safety • installation & integration • operating instructions • maintenance • service service mode quick guide 1. Thermistor 1 — temperature this will show the pure thermistor reading with no offsets taken into account. When placed in ice water this...
Page 52
User guide control operation - service 5 u-line.Com safety • installation & integration • operating instructions • maintenance • service 19. Individual component toggle relay #2. ... Relay #3. Will start the ice maker module and forward it through a full harvest cycle relay #4. Will send voltage to ...
Page 53
User guide service mode 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service service mode service mode quick guide number service mode menu item to navigate/access 1 view thermistor #1 cabinet temp no offsets use up/down to access and light bulb key to vi...
Page 54
User guide service mode 2 u-line.Com safety • installation & integration • operating instructions • maintenance • service errors *all errors are logged in memory. *only door error is displayed on the display and has an audible signal. *for 68118 models, pump error is displayed via alert light with n...
Page 55
User guide thermistor 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service thermistors thermistors are used for various temperature readings. Thermistors provide reliable temperature readings using a resistance which varies based on surrounding temperatur...
Page 56
User guide defrost 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service defrost these units are automatic (cycle) defrost unit will defrost itself when the control/sensor is satisfied of internal temperatures. Defrost mode ends when control/sensor asks fo...
Page 57
User guide remove fan and cover 1 u-line.Com safety • installation & integration • operating instructions • maintenance • service remove fan and cover convection cooling this unit is equipped with an advanced convection cooling system. Convection cooling stabilizes cabinet temperature, cools product...
Page 58
User guide remove fan and cover 2 u-line.Com safety • installation & integration • operating instructions • maintenance • service 11.While pulling the evaporator cover clear of the unit, it may be necessary to use your free hand to manipulate the fan plug end through the pass-through hole. 12.Remove...