Www.U-lineservice.Com phone (414) 354-0300 • fax (414) 354-7905 service & parts tech lines phone (800) 779-2547 • fax (414) 354-5696 onlineservice@u-line.Com ©2005 u-line corporation 02/2005 wh95tp, bi95btp and bcm95 ice makers for marine or recreational vehicle use installation guide.
Www.U-lineservice.Com 2 02/2005 wh95tp, bi95btp and bcm95 ice makers contents exterior cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 cut-out dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 product dimensions . . . . . . . . . . . . . . . . . . . . . . . . ...
02/2005 3 www.U-lineservice.Com wh95tp, bi95btp and bcm95 ice makers general precautions use this appliance for its intended purpose only and follow these general precautions along with those listed throughout this guide: warning shock hazard — electrical grounding required. • keep the unit unplugge...
Www.U-lineservice.Com 4 02/2005 wh95tp, bi95btp and bcm95 ice makers your u-line product has been designed for built-in installation. When built-in, your unit does not require additional air space for top, sides or rear. However, the front grille must not be obstructed and clearance is required for ...
02/2005 5 www.U-lineservice.Com wh95tp, bi95btp and bcm95 ice makers reversing the door all units may be left- or right-hand opening. Note: the grille should not yet be installed. If it has been installed, remove it for door reversing. See page 10. To reverse the door: 1. Remove travel pin from cabi...
Www.U-lineservice.Com 6 02/2005 wh95tp, bi95btp and bcm95 ice makers 9. Gently slide upper hinge through flange and fasten upper hinge to unit (three screws). Partially tighten screws. See figure 11. 10. Place door on lower hinge pin. 11. Align door pivot hole with pivot hole in upper hinge and inse...
02/2005 7 www.U-lineservice.Com wh95tp, bi95btp and bcm95 ice makers (bi95btp units only) units will accept a custom 1/4" thick insert to harmonize with or accent the surrounding decor. If this treatment is not included in this installation, go on to 5 adjust door. Custom 1/4" thick door panel inser...
Www.U-lineservice.Com 8 02/2005 wh95tp, bi95btp and bcm95 ice makers checking door alignment the unit’s door is aligned at the factory before shipment. However, its alignment could have been disturbed during shipment or during door panel installation. Important properly aligned, the door's gasket sh...
02/2005 9 www.U-lineservice.Com wh95tp, bi95btp and bcm95 ice makers 2. Locate the compression fitting and ferrule packed with the unit. Slide the compression fitting and ferrule over the 1/4-inch od water supply line. Do not use thread sealing compound or tape. Using two wrenches, tighten the compr...
Www.U-lineservice.Com 10 02/2005 wh95tp, bi95btp and bcm95 ice makers leveling information important it is extremely important that the unit sits on a level surface, as it does not have feet levelers. If it is not level, the ice mold will not fill evenly. Use a level to check the levelness of the un...
02/2005 11 www.U-lineservice.Com wh95tp, bi95btp and bcm95 ice makers 4. Insert the screw. Do not overtighten. Installation troubleshooting problem q: water is leaking under the unit. Solution a: a water leak under the unit is most likely caused by a bad connection in the water supply line. Make sur...
?2005 u-line corporation publication no. 30070e 02/2005 u-line corporation, located in milwaukee, wi, is a family operated manufacturer of built-in undercounter icemakers, combo ® icemaker/refrigerators, wine captain ® wine storage units, refrigerators, refrigerated drawers and refrigerator/freezers...
