U-Line H-3071 Instructions Manual

Summary of H-3071

  • Page 1

    Page 1 of 18 0514 ih-3071 π h-3071 nail gun 1-800-295-5510 uline.Com instructions safety instructions warning! Eye protection which conforms to ansi specifications and provides protection against flying particles both from the front and side should always be worn by the operator and others in the wo...

  • Page 2: Instructions Continued

    Page 2 of 18 0514 ih-3071 instructions continued operation warning! Always handle the tool with care: 1) never engage in horseplay; 2) never pull the trigger unless nose is directed toward the work; 3) keep others a safe distance from the tool while tool is in operation as accidental actuation may o...

  • Page 3: Instructions Continued

    Page 3 of 18 0514 ih-3071 instructions continued modes of operation bostitch offers two modes of operation for this series tool. Sequential trip (gray trigger) the sequential trip requires the operator to hold the tool against the work surface before pulling the trigger. This makes accurate fastener...

  • Page 4: Instructions Continued

    Page 4 of 18 0514 ih-3071 instructions continued lubrication continued cold weather operation for cold weather operation near and below freezing, the moisture in the air line may freeze and prevent tool operation. We recommend the use of bostitch winter formula air tool lubricant (included) or perma...

  • Page 5: Instructions Continued

    Page 5 of 18 0514 ih-3071 fastener depth control adjustment continued to adjust the fastener depth control warning! Disconnect tool from air supply before attempting any parts disassembly and before changing the work contacting element adjustment. 1. Push in on locking button. 2. Adjust contact arm ...

  • Page 6: Instructions Continued

    Page 6 of 18 0514 ih-3071 instructions continued tool operation continued b. The sequential trip (gray trigger) allows "place nailing" without the possibility of driving a second, unwanted fastener on recoil as described below under "contact trip". 2. Contact trip (conventional) operation (black tri...

  • Page 7: Instructions Continued

    Page 7 of 18 0514 ih-3071 instructions continued tool operation check continued in addition to the other warnings contained in this manual observe the following for safe operation • use the bostitch pneumatic tool only for the purpose for which it was designed. • never use this tool in a manner that...

  • Page 8: Troubleshooting Continued

    Page 8 of 18 0514 ih-3071 operating issue cause correction failure to cycle air supply restriction tool dry, lack of lubrication worn head valve o-rings broken cylinder cap spring check air supply equipment use bostitch air tool lubricant replace o-rings replace cylinder cap spring lack of power; sl...

  • Page 9: Troubleshooting Continued

    Page 9 of 18 0514 ih-3071 operating issue cause correction skipping fasteners; intermittent feed feed piston dry feed piston o-rings cracked/worn check pawl binding canister bottom not set correctly broken weld wires in nail coil add bostitch air tool lubricant in hole in feed piston cover replace o...

  • Page 10: H-3071

    Page 10 of 18 0514 ih-3071 π h-3071 cloueuse 1-800-295-5510 uline.Ca instructions consignes de sÉcuritÉ avertissement! Une protection oculaire qui satisfait à la spécification ansi et qui protège les yeux contre les particules projetées à la fois de face et de cÔtÉ doit être portée en tout temps par...

  • Page 11: Instructions Suite

    Page 11 of 18 0514 ih-3071 instructions suite utilisation avertissement! Utilisez toujours l'outil avec précaution : 1) ne vous chamaillez jamais; 2) n'appuyez jamais sur la détente si l'outil n'est pas orienté vers l'ouvrage; 3) veillez à ce que les autres se tiennent à l'écart de l'outil lorsque c...

  • Page 12: Instructions Suite

    Page 12 of 18 0514 ih-3071 instructions suite modes d'utilisation bostitch offre deux modes d'utilisation pour cet outil. DÉclenchement sÉquentiel (dÉtente grise) le déclenchement séquentiel exige que l'utilisateur appuie l'outil sur la surface de travail avant d'appuyer sur la détente. Ceci facilit...

  • Page 13: Instructions Suite

    Page 13 of 18 0514 ih-3071 instructions suite lubrification, suite utilisation par temps froid pour l'utilisation par temps froid à ou au-dessous du point de congélation, l'humidité dans la conduite d'air peut geler et rendre l'outil inutilisable. Nous recommandons l'emploi du lubrifiant d'hiver bos...

  • Page 14: Instructions Suite

    Page 14 of 18 0514 ih-3071 rÉglage du contrÔle de profondeur des attaches, suite pour rÉgler le contrÔle de profondeur des attaches avertissement! Déconnectez l'outil de l'alimentation en air avant de tenter tout démontage de pièces et avant de modifier le réglage de l'élément de contact avec la sur...

  • Page 15: Instructions Suite

    Page 15 of 18 0514 ih-3071 instructions suite utilisation de l'outil, suite b. Le déclenchement séquentiel (détente grise) permet le « clouage de précision » sans la possibilité de propulser une seconde attache non désirée en raison du recul, tel que décrit ci-dessous sous la rubrique « déclenchemen...

  • Page 16: Instructions Suite

    Page 16 of 18 0514 ih-3071 instructions suite contrÔle du fonctionnement de l'outil, suite en plus des autres avertissements contenus dans ce manuel, respectez ce qui suit pour une utilisation sÉcuritaire • utilisez l'outil pneumatique bostitch uniquement aux fins pour lesquelles il a été conçu. • n...

  • Page 17: Dépannage Suite

    Page 17 of 18 0514 ih-3071 problÈme de fonctionnement cause correctif défaillance de l'activation restriction de l'alimentation en air outil desséché, manque de lubrification joints toriques de soupape de tête usés ressort de couvercle de cylindre brisé vérifiez le matériel d'alimentation en air uti...

  • Page 18: Dépannage Suite

    Page 18 of 18 0514 ih-3071 problÈme de fonctionnement cause correctif saut d'attaches; alimentation intermittente piston d'alimentation desséché joints toriques de piston d'alimentation desséchés/usés vérifiez si le cliquet est coincé fond de la cartouche incorrectement réglé fil de soudage brisé da...