- DL manuals
- U-Reach
- Computer Hardware
- PRO250
- User Manual
U-Reach PRO250 User Manual
Summary of PRO250
Page 1
Pro250 high speed portable hdd duplicator user guide mini duplicator v2.5 u-reach www.Ureach-inc.Com the data equipment expert en.
Page 3
Content index 3 disclaimer of warranties disclaimer of warranties 3 before you start important notice 4 safety precautions 5 content index content index 4 chapter ① - product introduction 1 features 6 2 product overview 7 2.1 system overview 7 2.2 lcd configuration 7 3 function table 8 chapter ➁ - f...
Page 4
Disclaimer of warranties 4 all hdd duplicators are made specifically for data backup with legal authorities from copyright owners. Any unauthorized action of copyright is strictly prohibited, and the original manufacturer disclaims all warranties or representations of illegal actions by users. The m...
Page 5
Before you start 5 important notice • read the complete operation instruction carefully contributes to better operation. • make sure the source device is correct and workable. • to guarantee data consistency, strongly suggest the capacity of source and targets should be the same. • it is strongly su...
Page 6
Chapter ➀- product introduction 6 1 features • high copy speed supports for duplication and comparison. • support reading/writing speed measuring function. • show the detailed information of hdd and its quality. • auto power control system helps to protect the hdd from any damage during the insertio...
Page 7
Chapter ➀- product introduction 7 2 product overview 2.1 system overview backward forward / ok cancel / back source port target port red : fail green : pass yellow : powering 2.2 lcd configuration function time (mm:ss) target hdd total size (source) copy progress % copied processed size (target) pro...
Page 8
Chapter ➀- product introduction 8 3 function table function description 1. Copy to copy source hdd to multiple target hdds. Refer to function [6.1 copy area] for 4 different copy modes selection. 2. Compare to compare data bit for bit between source and target hdds. 3.Copy +compare it makes copy fir...
Page 9
Chapter ➀- product introduction 9 5. Utility 5.1 show disk info. Select one port and enter the function. 5.1.1 model number to show hdd's model number. 5.1.2 version of firmware to show hdd's firmware version. 5.1.3 serial number to show the serial number of hdd. 5.1.4 device power cycle to show the...
Page 10
Chapter ➀- product introduction 10 6. Setup 6.1 copy area 6.1.1 system and files to copy source hdd's data area only. 6.1.2 all partitions to copy source hdd's all partitions. 6.1.3 whole hdd to copy the whole source hdd. 6.1.4 percentage(%) to copy percentage range of source hdd. 6.2 skip error set...
Page 11
Chapter ➁- function introduction 11 1 copy it copies data from the source hdd to the target hdd. Please ensure you have selected the copy mode require before executing the copying process. Refer to function [6.1 copy area] for details. Copy process copie time total data capacity copied data capacity...
Page 12
Chapter ➁- function introduction 12 4 erase there are quick erase, full erase, dod erase, dod erasecomp , and secure erase, totally 5 kinds of erasing modes. Select the appropriate erase method when you would like to dispose or reuse the hdds. Note •users can go to function [6.4.2 erase master] to s...
Page 13
Chapter ➁- function introduction 13 erasing erasing 1 hdd dod erase 2:05 [02] 465g erase[00] 4818m the system will show the result after finishing dod erase pass: 5 fail: 0 4.4 dod erase comp as well as dod erase, this function will also execute compare function to make sure the random bit was corre...
Page 14
Chapter ➁- function introduction 14 4.5 secure erase the international authorized high standard secure erase function. It overwrites every single track on the hard drive with "00". Even pa/dco or other data area which are not able to load, can be erased all together. Note •please do not disrupt duri...
Page 15
Chapter ➁- function introduction 15 5.1.4 device power cycle this function is to show the count of hdd's turning on and off. [disc info.] 4.Device power c [device power c] 99 5.1.5 power-on hours this function is to show the total hours of hdd powering-on. [disc info.] 5.Power-on hours [power-on hou...
Page 16
Chapter ➁- function introduction 16 5.1.8 seek error rate this function is to show the error rate of searching for data. It can represent the damage rate of data stored in the hdd. [disc info.] 8.Seek error rat [seek error rat] 0 5.1.9 temperature this function is to show the temperature of hdd. [di...
Page 17
Chapter ➁- function introduction 17 ⊳ download the bios from the pc to your hdd. Hdd enclosure pc hdd usb ⊳ plug the hdd into port 1of the duplicator, select function 5.2.1 to update bios, and wait for about 1 minute to finish the update process. [update system] 1.Update bios 5.3 system info. This f...
Page 18
Chapter ➁- function introduction 18 5.5 read speed this function is to measure the reading speed of the hdd by reading the whole hdd. R 2:30 465g 89.0m/s 12.8g 5.6 write speed this function is to measure the writing speed of the hdd by writing the whole hdd. W 1:08 465g 89.6m/s 4423m note •this func...
Page 19
Chapter ➁- function introduction 19 tatget hdd 320gb when choosing “system and files copy”, only 20g data will be copied, and it just takes 6.2% time compared to “whole hdd copy”. The target hdd will be exactly the same as source hdd after copy. Source hdd 320gb data : 20gb partition1 : 90gb note •s...
Page 20
Chapter ➁- function introduction 20 6.1.3 whole hdd this mode will copy the entire hdd, regardless of content, format, partition or free space. This mode will take much more time to duplicate the source hdd completely. [copy area] whole hdd tatget hdd 320gb when choosing “whole hdd copy”, completed ...
Page 21
Chapter ➁- function introduction 21 tatget hdd 500gb only percentage range from25% to 32% will be copied. Source hdd 500gb data:250gb partition:250gb 500gb 25% 32% 25% 32% 6.2 skip error this function sets the volume of errors that is acceptable for you to skip during the copy process. [skip error] ...
Page 22
Chapter ➁- function introduction 22 [unknown format] copy unknown 6.4.1.2 skip unknown the setting skips the unknown format area during copy process. [unknown format] skip unknown 6.4.2 erase master this function is to set if erasing the source or not when executing erasing function. [erase master] ...
Page 23
Chapter ➁- function introduction 23 6.4.3.2 big random data a set of different random character to be written into a set of area. This erase pattern method is safer for preventing from data recovered. [erase pattern] big random data 26a5c8781 bf51337e81 aa9641d3b 5cda756b1 3baff21ff4 1fbac4c99 7edaf...
Page 24
Chapter ➁- function introduction 24 ❶ copy and setting: yes, copy. Copy data from source to target including hpa area of source. It will not only set the target hdd the same hpa setting as the source hdd, but also copy the data in the hpa area. ❷ no, keep hpa: no, don't copy. Copy data from source t...
Page 25
Chapter ➁- function introduction 25 6.4.7 transfer rate you can select the best transfer rate from udma 2 to udma7 for your hdd duplication process. If you are not confident on the hdd quality or you find a high failure rate on copy or compare. It is recommended to slow down the udma mode. [transfer...
Page 26
Chapter ➂ - specification 26 product name carry mini super high speed hdd dupe product number pro250 targets 1:1 (2-port) support hdd interface directly 1.8”/2.5”/3.5” sata hdd and ssd control button 4 push buttons( ▲ , ▼ , ok, esc ) compatible hdd/ssd via adapter all major brand of 2.5"/3.5" ide hd...
Page 28
Www.Ureach-inc.Com.