V2 s.P.A. Corso principi di piemonte, 65/67 12035 racconigi (cn) italy tel. +39.0172.812411 - fax +39.0172.84050 info@ gatestore.Co.Uk www.Remotecontrolgates.Co.Uk easy3-4 centrale di comando analogica per serrande avvolgibili i analog control unit for roller shutters gb armoire de commande analogiq...
English 17 index important remarks ........................................................................................................18 declaration of conformity ........................................................................................18 description of the control unit.............
English 18 important remarks for any installation problem please contact our customer service at the number +39-0172.812411 operating monday to friday from 8:30 to 12:30 and from 14:00 to 18:00. V2 has the right to modify the product without previous notice; it also declines any responsibility to da...
English 19 description of the control unit the easy digital control unit is an innovative v2 product that guarantees safety and reliability for the automation of roller shutters. • 230 vac output for 1 single-phase motor • 230 vac output for flashing light or timed courtesy light • input for key swi...
English 20 electric connections table warning: normally closed inputs stop (l2), photocell (l5), edge (l6), fire (l7), if not used must be bridged through the common terminal (-) warning: a wrong connection of the antenna compromises seriously the radio working of the control unit. Easy4 only.
English 21 optical edge installation (easy4 only) the easy4 main control unit is configured for the installation of one 24 vdc powered optical edge and transmitter power regulation. Please note: only use feel optical edges (please refer to the v2 catalogue). Connect the transmitter and receiver in a...
English 22 operation with a timer the control unit allows the connection of a timer for programming door opening and closing times. To use this function, it is essential to set function 3 (see function table) to automatic logic the timer should be connected between the start (l1) and common (l3) ter...
English 23 cable gland assembly the casing can accept 4 cable glands in the special easy-break housings. The type of cable gland is indicated in the figure. Please note: • remove the electronic circuit board before drill the casing. • drill the container using a suitably sized cutter, according to t...
English 24 when the main control unit is in standby mode, the eight leds on the card display the status of the inputs control unit in standby displaying the status of the inputs start up open stop auto down photo edge dm fire canc light motor test error to display the operational logics set, press t...
English 25 altering the functions to alter the operational logics, proceed as follows: 1. Press and hold the menu button for at least 2 seconds: the leds come on (for 12 seconds) depending on the status of the various functions. 2. Press the menu button briefly: the start/up led flashes to indicate ...
English 26 function table (the highlighted boxes indicate the factory default settings) function (led) led off led on 1. Start/up start/stop logic the start/up input controls the step or automatic operational cycle based on the programmed operational logic. The down input is inactive up/down logic t...
English 27 function table (the highlighted boxes indicate the factory default settings) function (led) led off led on 6. Dm/fire man present logic inactive by simply using the start command, the user can activate the automation device in opening or closing. The maximum duration of opening or closing...
English 28 adjusting the operating time to alter the motor operating time, proceed as follows: 1. Press and hold the menu button for at least 2 seconds: the leds display the status of the various functions 2. Within 10 seconds, press the menu button for at least 2 seconds: the leds come on showing t...
English 29 adjusting the pause time to alter the motor pause time, proceed as follows: 1. Press and hold the menu button for at least 2 seconds: the leds display the status of the various functions 2. Within 10 seconds, press the menu button for at least 2 seconds: the leds come on showing the opera...
English 30 operation with remote control operation of the remote control units depends on the configuration of function 1. Start/stop logic: only the memorised button activates an open or close command. Up/down logic: each button on the remote control is associated with a function. Simply memorise a...
English 31 deleting all the remote control units the delete all the codes in the memory, proceed as follows: 1. Disconnect the power from the main control unit 2. While pressing and holding the menu button, reconnect the power: the light/del led flashes 3. Release the menu button within 5 seconds: a...
English 32 led off on flashing led (combined with led 8) led 8 is off or on led 8 is blinking 1. Start/up on the start/up terminal, the contact is open on the start /up terminal, the contact is closed start command received from remote control writing in flash at the end of the programming is failed...
V2 s.P.A. Corso principi di piemonte, 65/67 12035 racconigi (cn) italy tel. +39.0172.812411 fax +39.0172.84050 info@ gatestore.Co.Uk www.Remotecontrolgates.Co.Uk.
