Summary of IP Survlliance
Page 1
- 1 - 1.3mega pixel ip camera user’s manual v_1.5 ip survlliance.
Page 2: Contents Table
- 2 - contents table over view ............................................................................................................................ 1 1.1 features ...................................................................................................................... 1 1.2 cms ...
Page 3: Over View
- 1 - over view 1.1 features 1.3 megapixel cmos sensor real-time h.264 built-in high sensitive microphone (optional) supports onvif standard to simplify integration and enhance interoperability supports h/w watchdog 1.2 cms camera management software you can install cms on a pc to management your ...
Page 4: Installation
- 2 - installation 2.1 minimum pc requirement hardware: intel○ r pentium○ r dual core tm 2 gb system memory or above sound card: directx○ r 9.0c compatible sound card video card: 3d hardware accelerator card required – 100% directx○ r 9.0c compatible ethernet network port/card 10/100 ethernet swit...
Page 5
- 3 - click [change adapter settings] double click [local area connection] click [properties].
Page 6
- 4 - double click [internet protocol version4(tcp/ipv4)] select [use the following ip address] and enter ip address, subnet mask and default gateway then press [ok]..
Page 7
- 5 - login ip camera with a web browser you may visit ipcamera’s homepage by ie or other compatible web browsers. Running a browser and enter ip camera’s ip‐ 192.168.1.221 in uri. Default account: admin default password: admin it displays system information after you login ip camera..
Page 8: 2.2 Live View
- 6 - 2.2 live view if you prefer using safari○ r , chrome○ r or firefox○ r , you have to install quicktime○ r player or the browsers can’t display video. If you use windows internet explore it will ask you install activex program when you first login..
Page 9
- 7 - you may need to change security parameter for live view player playing video well. Enter [control panel] then click [view network status and tasks]. Click [internet options]..
Page 10
- 8 - enter [security] page then click [custom level]. Set [download unsigned activex controls] to be [prompt]..
Page 11: 2.3 Status
- 9 - 2.3 status 2.3.1 information it displays hardware and firmware version of ip camera. 2.3.2 ping use “ping” to verify if a remote peer is reachable. Enter a remote ip address and click “test” to ping the remote host. The result would be shown on result table..
Page 12: 2.4 Settings
- 10 - 2.4 settings 2.4.1 video in this page you can set parameters for video stream. Camera: type the camera title. Resolution: select the required image resolution for the streams. Tab for stream 1‐ stream 2: for setting individual parameters for each stream. Frame rate: select the required frame ...
Page 13
- 11 - 2.4.2 camera brightness: select the required brightness level that ranges from 1 to 255. A brighter scene appears, if you choose higher level of brightness. Contrast: select the required range. The range available is between 1 to 255. Saturation: select the required saturation level that rang...
Page 14
- 12 - 2.4.3 audio enable audio: this will switch on/off the audio in camera. Audio mode: you can change the audio mode in the network camera in one of the following ways: ◎ only mic: enables only audio capture in camera. Encoding: set which codec is used for encoding. G711 and pcm..
Page 15
- 13 - 2.4.4 date time the ntp configuration allows ip camera obtain time from an ntp server or sync with your computer. Pc time: it displays current time on your computer. Device time: it displays current time on ip camera. Manual: click [pc time] then [accept] button to sync ip camera’s time with ...
Page 16: 2.5 Maintenance
- 14 - 2.5 maintenance 2.5.1 user account there are three operating levels when entering the web ui. Logging‐in as the admin allows you to change all settings. Admin: you can operate all functions in web interface. Operator: you can operate all functions in web interface except user account. Viewer:...
Page 17
- 15 - 2.5.2 profile backup configurations: click the backup settings button to save your current settings to a file. Restore configurations: you can backup settings to a file and restore settings from that file. You also can restore all settings back to default by selecting restore default configur...
Page 18
- 16 - 2.5.4 restart tick [restart] then click [accept] button to restart ipcamera. 2.5.5 language select a language for web gui..
Page 19
- 17 - appendix a – ipsearcher for searching ip camera on lan there is a tool which can running on a computer to search ip camera in local area network. It allows you to change ip camera’s ip address much easier. enter the folder [tools] in the cd. double click [ipsearcher]..
Page 20
- 18 - running [ipcamerasearcher] (it may show “ipcamerasearcher.Exe” if your windows○ r displays full file name.) click [search(s)].
Page 21
- 19 - it displays searched device(s) in 5‐10 seconds, please select an ip camera then click [updataip(i)]. enter user name and password then enter new ip, netmask and gateway. (the default user name is “admin”, password is “admin”) press ok then open a browser for connecting to this ip camera...
Page 22
- 20 - appendix b – http/rtsp streaming url ip camera supports http/rtsp streaming url for third part cms/nvr or software to get video from ip camera. http url: http:///video0.M4v example: http://192.168.1.221/video0.M4v rtsp 1st stream url: rtsp://.
Page 23
- 21 - appendix c –waterproof tape working process apply to the ip camera, rj-45 and dc power jack connector junction, when exposed in the outdoor environment, increase its water-resistance. Waterproof tape (attached as accessories with vehicle camera) rj45 connector junction dc jack power connect...