VacuMaid Turbocat pb-480blk Instruction Manual - page 4
The needle bearing sits at an angle. The flat side of the washer goes to
the rear. The flat side of the idler shaft goes to the front. Be sure the
needle bearing is reinserted as shown to ensure proper operation
(Fig. 6).
6. Place new belt on turbine sprocket and slide over brush roller. Be sure
belt is properly twisted to the right as shown in the illustration
(Fig. 5A).
7. Place brush roller and shaft supports back into housing. Push bumper
back onto housing (Fig. 5B).
8. Place metal base plate onto housing and reinsert three screws.
CA
CA
CA
CA
CAUTION
UTION
UTION
UTION
UTION
Mo
Mo
Mo
Mo
Moving par
ving par
ving par
ving par
ving parts--disconnect fr
ts--disconnect fr
ts--disconnect fr
ts--disconnect fr
ts--disconnect from v
om v
om v
om v
om vacuum system bef
acuum system bef
acuum system bef
acuum system bef
acuum system befor
or
or
or
ore ser
e ser
e ser
e ser
e servicing unit.
vicing unit.
vicing unit.
vicing unit.
vicing unit.
FIG. 6
If any of these problems occur:
1. Turbine runs slow
2. Brush makes knocking noise
Then, follow these steps:
1. Check bottom plate
2. Check belt and tension
3. Check beater brush
4. Check all intake areas for
obstructions and brush rotation
direction
Pg. 3-4
Pg. 4-5
Pg. 3
Pg. 3
TR
TR
TR
TR
TROUBLESHOO
OUBLESHOO
OUBLESHOO
OUBLESHOO
OUBLESHOOTING
TING
TING
TING
TING TURBINE PO
TURBINE PO
TURBINE PO
TURBINE PO
TURBINE POWERHEADS
WERHEADS
WERHEADS
WERHEADS
WERHEADS
If problem persists, check central vacuum cleaner system:
Non-Bag Model
1. Check dirt receptacle
2. Check guard screen
3. Check all filter screens
4. Check hoses for air leaks or
obstructions
Bag Model
1. Check paper bag
2. Check cloth bag
3. Check air filters
4. Check hoses for air leaks or
obstructions
3. Brush bounces in use
4. Brush is hard to push
GSH-230
GSH-230
GSH-230
GSH-230
GSH-230
Lo
Lo
Lo
Lo
Low
w
w
w
w V
V
V
V
Volta
olta
olta
olta
oltaggggge Swi
e Swi
e Swi
e Swi
e Swivvvvvel Hose*
el Hose*
el Hose*
el Hose*
el Hose*
•
Crush-proof hose
•
Light and Flexible
•
360° swivel--reduces cleaning
effort and strain on wrist. The
swivel also extends hose life.
W
W
W
W
W-419C
-419C
-419C
-419C
-419C
Chr
Chr
Chr
Chr
Chrome
ome
ome
ome
ome T
T
T
T
Telescopic R
elescopic R
elescopic R
elescopic R
elescopic Raaaaatc
tc
tc
tc
tchet
het
het
het
het W
W
W
W
Wand
and
and
and
and
•
Friction-fit design
•
From 22” to 39” extension length
•
Nylon collar ensures a smoother edge
and better fit.
T
T
T
T
Telescopic
elescopic
elescopic
elescopic
elescopic W
W
W
W
Wand Oper
and Oper
and Oper
and Oper
and Operaaaaating Instr
ting Instr
ting Instr
ting Instr
ting Instructions
uctions
uctions
uctions
uctions
T
T
T
T
To e
o e
o e
o e
o extend w
xtend w
xtend w
xtend w
xtend wand:
and:
and:
and:
and: Push the black button in the direction of the
arrow and hold in place. This releases the ratchet and allows the inner
wand to be extended. The wand can be locked into the desired length by
releasing the button at any of the notches. To retract the wand, hold
down on the black button and push the wand back into the outer wand.
T
T
T
T
To a
o a
o a
o a
o attac
ttac
ttac
ttac
ttach hose f
h hose f
h hose f
h hose f
h hose for use:
or use:
or use:
or use:
or use:
Lift valve door and insert cuff into hole.
T
T
T
T
To oper
o oper
o oper
o oper
o operaaaaate:
te:
te:
te:
te:
Slide switch on top of handle to ON position, then switch
OFF when finished.
*****Must be used with standard pin-jack valves.
Attaching tools or hose handle to the wand:
Attaching tools or hose handle to the wand:
Attaching tools or hose handle to the wand:
Attaching tools or hose handle to the wand:
Attaching tools or hose handle to the wand:
The straight, outer wand is designed to fit into your hose
handle. Turn the wand 1/4 turn in any direction to ensure
a good fit. The notched inner wand is designed to fit
into your cleaning tools. Once again, a 1/4
turn ensures a good fit. To remove the wand,
give a 1/4 turn in the opposite direction and
pull the cleaning tool or handle from the wand.
May need lubrication with wheel bearing grease.
Do not use any other type of lubricant.
5
6