VADDIO WallVIEW HD-USB PRO System Installation And User Manual - page 13
WallVIEW HD-USB PRO Camera System
WallVIEW HD-USB PRO Camera System Document Number 342-0467 Rev. B
Page 13 of 28
S
TEP BY
S
TEP
I
NSTRUCTIONS TO INSTALL THE
W
ALL
VIEW
HD-USB
PRO
C
AMERA
S
YSTEM
Step 1: Locating the Camera
Locate the camera mounting position while paying close attention to camera
viewing angles, lighting conditions, possible line of site obstructions, and
checking for in-wall obstructions where the camera is to be mounted. Pick a
mounting location to optimize the performance of the camera.
Like all Vaddio WallVIEW systems, the WallVIEW HD-USB PRO is easy to
install and operate. The product was specifically designed with CAT-5 cable
connectivity for the extension both the power and USB 2.0 signals.
Step 2:
After determining the optimum location of the camera system, run two (2) CAT-5 or better cables (if using both the
Extreme USB 2.0 Extenders and the Power Extension Module) from the computer location to the camera location.
Using both extenders together will limit the overall CAT-5 cable distance to distance to 150’. If using the Extreme
USB 2.0 Extenders alone with local camera power, the a single CAT-5 cable can be run up to 328.1’ (100m)
between the extenders TX and RX units. Make sure to mark and test the CAT-5 cable(s) and use real RJ-45
crimper and connectors using the 568B straight-through wiring standard. Please do not use the “feed-thru” type
RJ-45 connectors for professional installations.
Step 3:
Using the Thin Profile Wall Mount directions, install the mount. If mounting to the drywall with wall anchors, use
four (4) quality wall anchors. Make sure to level the mount and tighten the mounting screws.
Step 4:
Connect the CAT-5 cable to the EZ POWER VIDEO RJ-45 port on the back panel of the HD-USB camera.
Connect 1’ (305mm) USB 2.0 Cable Type-B Male into the USB Type-B Female on the back panel of the HD-USB
camera. Connect the Type-A Male into the Extreme USB 2.0 Extender TX unit’s Type-A Female jack. Plug the
USB CAT-5 cable into the RJ-45 Link Port of the TX Extender unit. With the supplied 1’ (305mm) EIAJ-03 to
EIAJ-03 power cable, connect one side to the 5 VDC supply on the camera and the other end to the Extreme
USB 2.0 TX Extender unit’s 5 VDC input. With the supplied Velcro, find a place on the back of the mount to
attach the USB extender and field dress the cabling to hide as much as possible.
NOTE: Check all CAT-5 cables for continuity in advance of the connection. Do not plug
the Power Extension Module CAT-5 cable into any other RJ-45 port but the EZ POWER
VIDEO port. There is 24 VDC Volts on Pins 1 & 2. Plugging into any other port may cause
damage to the camera system and void the warranty.
Step 5: At the Head-End
Plug the other end of the Power Extension Module’s CAT-5 cable into the RJ-45 port of the Power Extension
Module Marked EZ POWER VIDEO. Plug the USB extender’s CAT-5 cable into the RJ-45 Link Port of the
Extreme USB 2.0 Extender RX unit at the computer. With a USB 2.0 cable connect the USB Type-B Male to the
Type-B Female on the extender and the other end, Type-A Male into the computer.
Step 6: Last Chance to check the wiring
After double checking the wiring, plug the 24 VDC power supply into the Power Extension Module and plug the
power supply into the power outlet. The HD-USB camera should home and also should be sending USB 2.0
MJPEG video to the computer.
Checking out the Installation:
A.
On the RX and TX units, check that the Power, Host, and Link LEDs are on and that the Activity LED is
blinking. If the Link LED is permanently off, then the cabling between the LEX and REX unit is not installed
properly or is defective.
B. For Windows users (2000, XP, Vista, Windows 7), open Device Manager to confirm that the “Generic USB
Hub” has been installed.
WallVIEW HD-USB PRO