Valcom V-9923B Instruction Manual

Other manuals for V-9923B: User Manual, Datasheet

Page of 8

Download

Print this page

Bookmark us

Issue

947923

V-9923B

CODE CALL UNIT

INTRODUCTION

The V-9923B Code Call Unit provides two or

three digit code call paging via a loop start trunk

port on a PABX or by the use of a spare line

button on a key system.

The V-9923B complies with Part 68 of the FCC

Rules and Regulations and has been granted

FCC Registration #BAFUSA-68753-KX-N.

The ringer equivalence is 0.1B and the unit

requires a USOC RJ21X connector.

In accordance with FCC Rules and applicable

tariffs, this code call unit may only be installed

with the authorization of the owner of the host

system.

The FCC Registration #BAFUSA-68753-KX-N

will be listed in the affidavits filed with the

telephone company; it will also be recorded in

the system log kept by installation and

maintenance personnel. The local telephone

company is to be notified of the FCC registration

number when this code call unit is installed.

SPECIFICATIONS

The V-9923B is capable of providing code

signaling for paging purposes; it provides for

"meet me" answer of code call and provides talk

circuit and signaling tone.

Features

• Trunk level access on PABX's, station level

answer

• Can be used with 1A2 type key systems

• 81 two digit codes or 729 three digit codes

• Uses rotary or tone dial signaling

• Dial tone to calling party

• Coded tone output for paging systems

• Switch controlled code verification tone

• Automatically discontinues code sending

when answered

• Capable of being used with another V-9923B

to provide two link operation

• Uses standard 1A2 key system voltages

• Mounts on the wall, in a key cabinet, or in

the PABX Cabinet

Capacity

Each V-9923B Code Call Unit provides the

necessary equipment for 1 link of Code Call.

For an additional link of Code Call, another

V-9923B is required (two links maximum).

Dimensions

7.1"H x 5.9"W x 2.1"D

(18.03cm H x 14.99cm W x 5.33cm D)

Power Requirements

Valcom V-9923B requires –24VDC talk battery

and –24VDC signal battery. Below shows

current consumption and voltage range:

"A" Battery:

Range: –21.5 to –26VDC

Idle: 0mA

Operating: 65mA

"B" Battery:

Range: –21.5 to –26VDC

Idle: 75mA

Operating: 125mA

1 2 3 4 5 6 7 Next › »

Summary of V-9923B

Page 1
Issue 5 1 947923 v-9923b code call unit introduction the v-9923b code call unit provides two or three digit code call paging via a loop start trunk port on a pabx or by the use of a spare line button on a key system. The v-9923b complies with part 68 of the fcc rules and regulations and has been gra...
Page 2
2 947923 nominal timing and frequency specifications the timing and frequency specifications of the valcom v-9923b code call unit are shown in table 1. Figure 1 is a timing chart showing the nominal timing of a code call. Table 1 dial tone frequency 180hz coded tone frequency 550hz time tones broadc...
Page 3
3 947923 installation precautions all precautions have been taken at the factory to insure that the equipment functions properly when installed correctly. Please follow the precautions listed below before applying power to the equipment or the equipment may be damaged and the warranty voided. A) if ...
Page 4
4 947923 power connections the connections required to connect the v-9923b to a power supply are shown in figure 6. Correct polarity must be observed for the unit to function properly. Output connections the v-9923b contains a tone generator and isolation transformer to allow direct hook-up to the p...
Page 5
5 947923 table 2 troubleshooting chart problems probable causes and solutions no dial tone no tone output unit doesn't answer unit cuts off on answer verify power connections; check operation of unit by placing test telephone across the t and r leads and going off hook. If dial tone present, check w...
Page 6
6 947923 26 1 27 2 28 3 29 4 30 5 31 6 32 7 33 8 34 9 35 10 36 11 37 12 38 13 39 14 40 15 41 16 42 17 43 18 44 19 45 20 46 21 47 22 48 23 49 24 50 25 w/bl bl/w w/o o/w w/g g/w w/br br/w w/s s/w r/bl bl/r r/o o/r r/g g/r r/br br/r r/s s/r bk/bl bl/bk bk/o o/bk bk/g g/bk bk/br br/bk bk/s s/bk y/bl bl/...
Page 7
7 947923 part of pbx loop start outgoing c.O. Trunk (rotary or t.T.) pbx analog station port t r t r t r to ro w/bl (1) bl/w (2) w/br (7) br/w (8) figure 4 connections of v-9923b to pabx t r w/bl (1) bl/w (2) part of connecting block row b inh l g/w (6) w/o (3) o/w (4) ls to 10 vac on power supply t...
Page 8
8 947923 bk/bl bl/bk diode 1n4003 or eq. (portion of connecting block) dc power supply depends on relay requirements relay coil figure 7 connections of v-9923b for operating a dc slave relay three digit operation two digit operation no code verification code verification must be in the on position s...