Valencia Euro EGZ90GSV Use, Installation And Maintenance Instructions

Manual is about: BUILT-IN HOT PLATES

Summary of EGZ90GSV

  • Page 1

    We ask that you carefully read the instructions within this booklet to enable you to abtain quality results from the outset. The appliance must be installed only by an authorised person in compliance with the instructions provided. The manufacturer declines all responsability for improper installati...

  • Page 2: Model:  Egz90Gsv

    2 natural u-lpg 1 ultra rapid gas burner/wok 14.5 mj 11.4 mj 2 rapid gas burner 12.0 mj 10.4 mj 3 semi-rapid gas burner 7.1 mj 6.2 mj 4 auxiliary gas burners 4.1 mj 3.5 mj 5 fish gas burner 12.0 mj 10.4 mj 6 right trivet 2 burners 7 left trivet 2 burners 8 central u.Rapid burner/ wok trivet 9 centra...

  • Page 3: Use

    1) burners a diagram is screen-printed above each knob on the front panel. This diagram indicates to which burner the knob in question corresponds. After having opened the gas mains or gas bottle tap, light the burners as described below: - manual ignition push and turn the knob corresponding to the...

  • Page 4: Use

    4 use notes: use of a gas cooking appliance produces heat and moisture in the room in which it is installed. The room must therefore be well ventilated by keeping the natural air vents clear (fig. 3) and by activating the mechanical aeration device (suction hood or electric fan fig. 4 and fig. 5). I...

  • Page 5: Cleaning

    Cleaning fig. 6 5 important: always disconnect the appliance from the gas and electricity mains before carrying out any cleaning operation. 2) hot plate periodically wash the hot plate, the enamelled steel pan support, the enamelled burner caps “c” and the burner heads “m” (see fig. 6) with lukewarm...

  • Page 6: Installation

    Installation technical information for the installer this appliance shall be installed only by authorised personnel and in accordance with the manufacturer’s installation instructions, local gas fitting regulations, municipal building codes, water supply regulations, electrical wiring regulations, a...

  • Page 7: Installation

    5) gas connection the gas connection is located in the rear and on the underside of the appliance 100 mm from the right hand side. There are two ways to carry out the connection to the main gas line: a. The hotplate can be connected with rigid pipe as specified in as5601 table 3.1. B. If installing ...

  • Page 8: Installation

    6) electrical connection the appliance is supplied with a 1800 mm long flexible supply lead. The point of attachment for this lead is located at the rear and on the underside of the appliance 380 mm from the right hand side. The voltage and power consumption are detailed on the underside of the appl...

  • Page 9: Adjustments

    9 adjustments fig. 14/a always disconnect the appliance from the electricity main before making any adjustments. All seals must be replaced by the technician at the end of any adjustments or regulations. Our burners do not require primary air adjustment. A) data label the data label is located on th...

  • Page 10: Conversions

    Conversions 8) u-lpg to natural gas conversion procedure appliance models: gas stainless steel hotplate model: egz90gsv 1. Remove each burner cap and burner skirt. 2. Remove the u-lpg main injector with a 7 mm/vf tube spanner and replace with the appropriate size natural gas injector for each burner...

  • Page 11: Conversions

    11 conversions 10) replacing the injectors the burners can be adapted to different types of gas by installing injectors suited to the type of gas required. To do this, first remove the burner tops using a wrench “b”. Now unscrew injector “a” (see fig. 15) and fit a injector corresponding to the type...

  • Page 12: Servicing

    12 servicing always turn off the electrical ignition before proceeding with any servicing operation. Servicing should be carried out only by authorised personnel. 11) replacing hot plate parts to replace the components fitted inside the hob, take off the knobs, all the movable parts of the hobs (tri...

  • Page 13: Servicing

    13 servicing type of type of single - phase hot plate cable power supply cable types and sections attention!!! If the power supply cable is replaced, the installer should leave the ground wire longer than the phase conductors (fig. 19) and comply with the recommendations given in paragraph 6. Fig. 1...

  • Page 14

    14 technical assistance and spare parts before leaving the factory, this appliance will have been tested and regulated by expert and specialized personnel in order to guarantee the best performances. Any repairs or adjustments which may be subsequently required may only be carried out by qualified p...

  • Page 15

    15.

  • Page 16

    16.