C1 inset live fuel effect gas fire (gc no. 32-032-46) incorporating the control (manufacturer ref. 640) 3002526/03 owner’s guide when converted using conversion kit no.0591301 this appliance is for use with propane gas (g31) this appliance is for use in the united kingdom (gb) and the republic of ir...
Owner’s guide page 2 safety first. This fire is ce approved and designed to meet the appropriate british standards and safety marks. Quality and excellence this fire has been manufactured to the highest standards of quality and excellence and was manufactured under a bs en iso 9001 quality system ac...
Owner’s guide page 3 l i s t o f c o n t e n t s safety ........................................................................................................................... 4 appliance dimensions......................................................................................... 6 gas co...
Owner’s guide page 4 graph 1. Combustible shelf clearances. S a f e t y if you smell gas don’t smoke extinguish all naked flames don’t turn electrical switches on or off turn off the gas supply at the meter open doors and windows to get rid of the gas immediately call the gas emergency service - see...
Owner’s guide page 5 do provide a suitable guard that complies with bs 6539 or 6778 for the protection of young children, the elderly and the infirm. Such a guard is also recommended for the protection of pet animals. (although this fire conforms to all the applicable standards, it is a heating appl...
Owner’s guide page 6 a p p l i a n c e d i m e n s i o n s dimension x is 50mm. This can be deleted when installing into a pre-cast or clay flue block system. Figure 1 appliance dimensions..
Owner’s guide page 7 g a s c o n s u m p t i o n model 640 has a maximum natural gas input of 6.85kw (gross) has a maximum natural gas output of 4.0kw (gross) has a minimum natural gas input of 2.7kw (gross) has a minimum natural gas output of 1.34kw (gross) model 640 when converted using kit number...
Owner’s guide page 8 figure 2. The control to light the fire the slide control is shown in figure 2. 1. Slide the control button to the bottom (ignition) position marked . In this position, the electronic ignition system should cause a series of sparks which should light the pilot. Within four secon...
Owner’s guide page 9 figure 3. Lighting with a taper iv) if operating the appliance for long periods it is beneficial occasionally to change the settings. This will also help to remove any carbon deposits that may form during operation. To turn the fire off slide the button up past the high heat pos...
Owner’s guide page 10 c l e a n i n g to maintain the high performance and quality finish of your fire please follow these guidelines: • before attempting to clean the fire, please remember to turn off the fire and wait for the appliance to cool. The fire will retain heat for some time before cleani...
Owner’s guide page 11 figure 5. Front coal location figure 4. Ceramic base location f u e l b e d r e f i t t i n g 1. Place the ceramic base coal in the burner compartment. The bottom rear face of the coal should rest on the angled ledges at the back of the burner compartment. The bottom front edge...
Owner’s guide page 12 5. Install the 12 loose coals as follows. The underside of each coal is marked with a letter ‘a’ to ‘l’ and an arrow. 6. The coals should be positioned so that the arrows always point towards the back of the firebox. When located into position the stem of each arrow should be a...
Owner’s guide page 13 11. Hold coal ‘d’ upright with the arrow pointing to the top. Locate coal ‘d’ as shown in figure 9. 12. Hold coal ‘e’ upright with the arrow pointing to the top. Locate coal ‘e’ as shown in figure 10. 13. Hold coal ‘f’ upright with the arrow pointing to the top. Locate coal ‘f’...
Owner’s guide page 14 15. Locate coals ‘g’ to ‘k’ so that they are firmly seated in the valleys in the coal base. 16. Hold coal ‘g’ upright with the arrow pointing to the top. Locate coal ‘g’ as shown in figure 12. 17. Hold coal ‘h’ upright with the arrow pointing to the top. Locate coal ‘h’ as show...
Owner’s guide page 15 19. Hold coal ‘j’ upright with the arrow pointing to the top. Locate coal ‘j’ as shown in figure 15 20. Hold coal ‘k’ upright with the arrow pointing to the top. Locate coal ‘k’ as shown in figure 16 21. Hold coal ‘l’ upright with the arrow pointing to the top. Locate coal ‘l’ ...
Owner’s guide page 16 m a i n t e n a n c e battery replacement this appliance requires one 9v pp3 ever ready silver seal (or equivalent) battery. To replace the battery remove the bottom front cover casting. Fit the new battery firmly to the connections on the ignition block (see figure 18). Regula...
Owner’s guide page 17 a) model and gc number. B) serial number (to be found on a ‘swing’ plate located below the burner and behind the bottom front cover). • if you wish to replace any of the owner replaceable parts listed below, please quote the part number when ordering. Description part no. Base ...
