5131426/01 model 823 electric heater fitted with one of the following fascia: liberty or vermont. (gc no. Ef-032-29) this guide is intended to help you install and care for your valor fires electric heater. Please read carefully before installing and using your heater. However, if further informatio...
© baxi heating u.K. Limited 2008. All rights reserved. No part of this publication may be reproduced in any material form (including photocopying), stored in any medium by electronic means (including in any retrieval system or database) or transmitted, in any form or by any means, whether electronic...
Safety first. Valor fires heaters are ce approved and designed to meet the appropriate british standards and safety marks. Quality and excellence. All valor fires heaters are manufactured to the highest standards of quality and excellence and are manufactured to iso 9001 customer care thank you for ...
1. Handling and unpacking before continuing any further with the installation of this heater please read the following: important safety instructions. The approximate lifting weights (kg) of the heater parts are listed below: - heater heat engine fascia rear spacer front spacer coals liberty 5.5 6.9...
Never never leave children unsupervised in a room where the heater is on and unguarded. Never obstruct or cover the fan outlet or force items into heater openings. Never install or use the heater anywhere where water is in use, i.E. Bathrooms, kitchens, shower rooms and swimming pools etc. Never use...
3. Fitting the heater the installation of this heater requires a reasonable level of diy skills. Please read this guide thoroughly before commencing installation and if in doubt, seek help from a competent person. Do i need any tools? 1. You may need the following screwdrivers: - a pozidrive / phill...
Page 7 installer and owner guide © baxi heating u.K. Limited 2008. Figure 1. Contents (items are not to scale) contents qty (illustrations are not to scale) contents qty (illustrations are not to scale) heater 1 cover plate 1 rear spacer frame 1 wall mounting bracket 2 front spacer frame 1 bag of co...
Heater dimensions. Moving the cable guide. At the base of the heater you will find an electric cable which runs through a rectangular plastic cable guide. As supplied the cable guide is fitted into the rectangular cut-out on the right side of the heater. If required, the cable guide can be removed a...
Cable guide will open (see figure 3 - item 2). 3. Lift the electric cable clear of the cable guide. 4. Hold the bottom of the cable guide close to the heater then gently pull the cable guide away from the rectangular slot (see figure 3 - item 3). Fitting the cable guide. When fitting the cable guide...
Heater fixing. All fixings necessary to install the heater have been identified in figure 1. The heater must be fixed into position. Fitting a wall mounting bracket to the wall. Supplied with the heater are two wall mounting brackets (see figure 1). Fix one of these brackets to the wall as follows. ...
Fitting the spacer frames. (see figure 5). The heater is supplied with two spacer frames. Identifying the spacers is easy as the front spacer has two brackets screwed to the top. 1. Position the front spacer so that the narrow flange is at the front. Hold the spacer above the heater and lower it ove...
2. Supplied with the heater is a lower securing bracket (see figure 1). Offer one side of the bracket into the slot at the rear base of the heater (see figure 7). Swing the opposite side into place, until the bracket is horizontal, then pull down to hold in place (see figure 7). The bracket will rem...
Fitting the diffuser. The heater is supplied with a diffuser (see figure 1). 1. Locate the diffuser on the ledge immediately below the screen (see figure 9). Fitting the fascia before fitting the fascia complete the last page of this guide. 1. Remove the fascia from its packaging. 2. The heater is s...
4. Using the heater the heater is supplied with a battery operated, infra red remote control handset. It provides ‘on / off’, ‘lamp’, ‘heat 1’ and ‘heat 2’ functions (see figure 12). The heater is fitted with an ‘off’ / ‘function’ button should the handset be lost or the batteries fail (see figure 1...
5. Cleaning and maintaining the heater how do i clean my heater? The heater fascia and glass parts need only to be wiped clean with a dry soft cloth, do not use polishes or abrasive materials. This may not work on the fascia when removing fingerprints etc. In this case apply a very small amount of ‘...
2. My heater is on but there is no light or heat. The first thing to do is check the wall socket. To do this plug in a known working appliance. If the appliance you have plugged in works then there is a good chance that the problem lies with the 13amp fuse in the heater plug. If either fuse or socke...
7. Warranty and service information for the customer standard warranty terms & conditions the warranty is for 12 months subject to contract. In the united kingdom servicing can be carried out either by a heateam service engineer or a corgi registered installer. You must register your heater with hea...
What this warranty does not cover repairs to heaters which haven’t been installed properly and as set out in this guide. Faults caused by inadequate supply of electricity. Reimbursement of any third party repair or replacement costs that we haven’t been told about or agreed with you in advance. Comp...
To be completed by the customer: page 19 installer and owner guide © baxi heating u.K. Limited 2008. Brand (please tick) baxi valor wonderfire other........................ D d m m y y date of installation fascia name (block capitals) fascia code - can be found close to the information label (block ...
© baxi heating u.K. Limited 2008..
