5129777/01 installer and owner guide © baxi heating u.K. Limited 2007. Model 834 electric heater fitted with one of the following fascia hanging deco, distinction 2, panache or washington. (gc no. Ef-032-24) this guide is intended to help you install and care for your valor fires electric heater. Pl...
© baxi heating u.K. Limited 2007. All rights reserved. No part of this publication may be reproduced in any material form (including photocopying), stored in any medium by electronic means (including in any retrieval system or database) or transmitted, in any form or by any means, whether electronic...
Safety first. Valor fires heaters are ce approved and designed to meet the appropriate british standards and safety marks. Quality and excellence. All valor fires heaters are manufactured to the highest standards of quality and excellence and are manufactured under a bs en iso 9001 quality system ac...
1. Handling and unpacking fascia parts may be covered in protective film. Ensure that this has been removed before using the heater. Before continuing any further with the installation of this heater please read the following: important safety instructions. ! The lifting weights of the heater parts ...
2. Safety this appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety...
Important electrical safety the heater must not be located in front of or under an electrical socket, the socket must always be accessible in order to disconnect the heater from the electrical supply for maintenance and cleaning. On the panache and washington models the electrical socket must not be...
3. Fitting the heater the installation of this heater requires a reasonable level of diy skills. Please read this guide thoroughly before commencing installation and if in doubt, seek help from a competent person. Before fitting the fuel support ensure that the back page of this guide is completed. ...
Securing the heater. The contents have been identified as in figure 2 (the fascia is not shown). Additional fixings may be required if fitting the heater to a plasterboard wall that has a wooden frame behind it. In such cases we recommend the use of heavy duty cavity fixings. Page 8 installer and ow...
Fitting the heater. Hanging deco and distinction 2 models. 1. There is a lower support bracket supplied with the heater. Secure this to the rear base of the heater with the two screws supplied (see figure 3). 2. Decide the location of the heater. 3. ‘hanging deco’ fascia only - if the heater is to b...
Shoulder screw and therefore cannot be fitted level with the hearth or finished floor level as the ‘hanging deco’ above. 4. If fitting to a conventional brick wall then use the outer slotted holes in the bracket. If fitting to a plasterboard wall that has a wooden frame behind it then use all four f...
Six screws supplied (see figure 5). 2. Place the surround and plinth assembly against the wall ensuring that the electrical cable is on the required side of the surround. Fitting the hanging deco fascia. 1. On the underside of the fascia top are two sets of pilot holes. Align the holes in the fascia...
2. The bottom of the fascia has a bracket with two holes. Secure the bottom of the fascia to the heater using the two knurled shoulder screws supplied (see figure 8). Fitting the fuel support (all models). Before fitting the fuel support ensure that the back page of this guide is completed. 1. Locat...
4. Using the heater important safety never cover the heater or obstruct the openings at the base of the heater, this could cause overheating and consequent risk of fire. What are the three switches for? The heater is operated by three switches located below the hood on the left hand side of the heat...
5. Cleaning and maintaining the heater how do i clean my heater? The heater fascia and plastic parts need only to be wiped clean with a dry soft cloth, do not use polishes or abrasive materials. I have a problem with my heater! Important safety before undertaking maintenance or replacing the lamp(s)...
3. My heater is on but there is no heat. A cut out device is fitted to the heater to prevent damage due to over heating. If it operates due to an obstruction in the airflow, the heater must be turned off and allowed to cool for 15 minutes and the obstruction removed before restarting. 4. I have a pr...
7. Warranty and service information for the customer standard warranty terms & conditions the warranty is for 12 months subject to contract. In the united kingdom servicing can be carried out either by a heateam service engineer or a corgi registered installer. You must register your heater with hea...
What this warranty does not cover repairs to heaters which haven’t been installed properly and as set out in this guide. Faults caused by inadequate supply of electricity. Reimbursement of any third party repair or replacement costs that we haven’t been told about or agreed with you in advance. Comp...
Page 18 installer and owner guide © baxi heating u.K. Limited 2007..
To be completed by the customer: page 19 installer and owner guide © baxi heating u.K. Limited 2007. Brand (please tick) baxi valor wonderfire other........................ D d m m y y date of installation a label containing the fascia code may have been placed inside this box. Fascia name (block ca...
© baxi heating u.K. Limited 2007..
