1. DL manuals
  2. Valor
  3. Indoor Fireplace
  4. Legend 936XN
  5. Installation and owner's manual

Valor Legend 936XN Installation and owner's manual

Manual is about: FREESTANDING DIRECT VENT GAS FIREPLACE HEATER

Summary of Legend 936XN

  • Page 1

    Legend stove models 936xn (natural gas) 936xp (propane) freestanding direct vent gas fireplace heater installation and owner’s manual for pedestal base with contemporary front or legs with traditional front please read this manual before installing and operating. Vous pourrez vous procurer un exempl...

  • Page 2

    2 contents page safety information 3 installation options 4 general data 4 location in room 5 vent location 5 supply gas 8 pack contents 8 installing • appliance preparation 8 • vent opening preparation 9 • gas supply installation 10 • base & main appliance installation 10 • pedestal base 10 • base ...

  • Page 3

    3 safety information due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies. Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns or clothing ignition. Young children should be ca...

  • Page 4

    4 13 7 / 8 ” 35” 71 1 / 4 ” 47 5 / 8 ” 84” 120 1 / 4 ” height from floor to center of vent duct horizontal length from vent elbow center to outside face of wall 2 kits required 1 kit required no kit required (minimum distance to inside wall face 7”) with pedestal base 13 7 / 8 ” 35” 71 1 / 4 ” 46” 8...

  • Page 5

    5 2.4 orifice data for verification only. Do not attempt to drill or otherwise modify appliance input. Model orifice type no.Of holes diameter (ins.) 936 xn pilot front rear amal 40 cat.18-340 cat.18-380 1 7 7 0.022 0.025 0.027 936 xp pilot front rear cat.960-10 cat.960-110 cat.960-130 1 1 1 0.01 0....

  • Page 6

    6 with plinth with legs fig.2 dimensions & clearances.

  • Page 7

    7 key vent terminal locations - minimum distances minimum clearance see figure 3 ins cms a clearance above grade, verandah, porch, deck or canopy 12 30 b clearance to window or door that may be opened 12 30 c clearance to permanently closed window (recommended to prevent condensation on window) 12 3...

  • Page 8

    8 fig.5 window removal 4. Supply gas the supply connection is 3 / 8 ”npt. Openings for the gas supply are provided for rear or under-floor connection (see figure 2). 5. Pack contents the complete appliance is contained in three packs. One of the alternative base support and front designs will be inc...

  • Page 9

    9 6.3 fit exhaust port cover (see figure 6a) remove four screws from under the top of the firebox. Fit the exhaust port cover and secure with the four screws. 7. Vent opening preparation important: this appliance is supplied with a vent unit requiring the center of the vent hole to be 47 5 / 8 ” abo...

  • Page 10

    10 7.11 insert the shield tube into the wall from the outside wall. Push the tube firmly in so that it locates fully over the dished diameter of the inside wall plate. Trim the tube if necessary (see figure 9). The outside end of the tube can be temporarily held in place by inserting wedges of cardb...

  • Page 11

    11 9.2 base with legs 9.2.1 detach the door retaining bracket (located near the rear right corner of the appliance main unit) by removing two screws (see figure 11). 9.2.2. Swing the bottom of the door forward to release the bottom pin from the slot in the case and lift the door clear (see figure 11...

  • Page 12

    12 10.1 if using any optional vent extension kits #905vek, cut to the required sizes - see venting graph figure 1. 10.2 identify the appliance top decorative collar. The collars have identification labels. Remove the label. Place the collar over the vertical section of the elbow or vertical extensio...

  • Page 13

    13 10.17 place a piece of card, thick paper, etc. Over the top of the appliance to protect it. Secure the elbow or extension at the appliance ducts by drilling and securing with two #6 tapping screws provided (lift the decorative vent collar clear while working). See figure 17. Make sure that the dr...

  • Page 14

    14 11.5 connect the other end of the inlet pipe to the elbow attached to the supply line. 12. System check 12.1 pressure test the supply line for leaks. • the appliance and its individual shut-off valve must be disconnected from the gas supply piping system during any pressure testing of that system...

  • Page 15

    15.

  • Page 16

    16 15. Ceramic fuel bed assembly 15.1 place the ceramic back wall in position centrally at the back of the firebox. It must rest on the metal ledge at the back of the firebox (see figure 23). 15.2 place the ceramic side walls in position at the sides of the firebox. The sides are left and right hand...

  • Page 17

    17 15.5 place the two front logs in position on the front rail of the firebox. It may be necessary to raise the center log slightly in order to fit the left-hand front log. 16. Controls operation check 16.1 refit the control cover panel. Refit the two control knobs 16.2 if installed with a pedestal ...

  • Page 18

    18 18. Facia installation 18.1 contemporary front only : fit the ashlip to the facia unit with 4 screws (see figure 30). 18.2 locate the facia unit to the appliance front - see figure 31. Locate at the top corners and at the bottom. We suggest the following order: 1) angle the top of the facia again...

  • Page 19

    19 20. Operating procedure the operating instructions are also inside the control panel door. 20.1 for your safety this appliance is fitted with a flame supervision device which will shut off the gas supply if, for any reason, the pilot flames go out. This device incorporates a fixed probe which sen...

  • Page 20: Lighting Instructions

    20 for your safety read before lighting warning : if you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions ...

  • Page 21: Heating

    21 manufactured by heating birmingham, england because our policy is one of constant development and improvement, details may vary slightly from those given in this publication. © valor ltd. 1999.