This manual contains instructions to install the engine only. A front is also required to complete this installation. A barrier screen is pro- vided with the front. Refer to the manual sup- plied with the front for installation. — do not store or use gasoline or other fl ammable vapors and liquids i...
Table of content designed and manufactured by / for miles industries ltd. 190–2255 dollarton highway, north vancouver, bc, canada v7h 3b1 tel. 604-984-3496 fax 604-984-0246 www.Valor fi replaces.Com © copyright miles industries ltd., 2016 the information contained in this installation manual is beli...
Safety precautions ! Children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid burns or clothing ignition. Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young children and others may be su...
Safety and your fireplace please follow these important child safety precautions and recommendations, • parts of your valor fireplace become extremely hot while in operation. • the glass viewing window temperature can exceed 500 f at full capacity. Momentary contact with a hot glass surface can caus...
Operating your fireplace for the first time when operating your new fi replace for the fi rst time, some vapors may be released due to the burning of curing compounds used in the manufacture of the appliance. They may cause a slight odor and could cause the fl ames to be the full height of the fi re...
Bottom of window (wider frame) owner’s information cleaning your fireplace important - glass cleaning - mineral deposits one of the by-products of the combustion process in a gas appliance is a mineral which can show up as a white fi lm on the ceramic glass of the viewing door. The composition of th...
Owner’s information 4. If the hot glass warning plate has been removed from the front lower corner of the window, reinstall it by sliding it between the glass and the frame as indicated. 5. Replace the front or trim with the barrier screen attached. Checking pilot and burner flames a periodic check ...
Owner’s information locating lighting, operation and rating information card the lighting, operation and rating information card is located under the burner. Pull the card out out to read it. There is important information on both sides of the card. Servicing your fireplace if any attention is requi...
Remote control operation your fi replace remote control helps you get the comfort, convenience and aesthetics you want from your gas fi replace. The remote controls your fi replace in different ways. Important: before you begin, please note that on this system, the settings of time, temperature and ...
Remote control operation setting the fl ame use this setting when you want a particular fl ame level. For instance, you want to watch fl ames burn at their highest level and you don’t mind if the room is too hot. 1. To raise the fl ame, press and hold the ▲ button until the flame gets to the desired...
Options required kits* fuel beds (choose one) 739lsk log set 739rsk rock set 739dwk driftwood kit liners (choose one) 739rgl re fl ective glass liners 739fbl fluted black liners 739vrl valor red brick liners inner fronts (choose one) barrier screen 741 contemporary steel front 4003360 742 traditiona...
Lighting instructions for your safety read before lighting warning: if you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot, which must be lighted by hand. When lighting the pilot, follow ...
X x ratings model ng lpg gas natural propane altitude (ft.)* 0-4,500 feet* input maximum (btu/h) 24,000 24,000 input minimum (btu/h) 6,500 13,000 manifold pressure (in w.C.) 3.95 9.5 minimum supply pressure (in w.C.) 5.0 11.0 maximum supply pressure (in w.C.) 10.5 14.0 main burner injector marking 8...
Overview this appliance, as supplied, may only be installed in an existing unal- tered, functioning solid-fuel burning fi replace with a working fl ue and con- structed of non-combustible material. This appliance is approved for installation into combustible type con- struction only when using the 7...
28-5/8” (727 mm) 19-1/2” (495 mm) 7-7/8” - 9-7/8“ (200 - 251 mm) varies with outer trim options 20” (508 mm) gas inlet gas connection optional outer trim or surround sold separately 12 - 14” (305 - 357 mm) varies with outer trim options x y dimensions cavity check that masonry step does not interfer...
9” (229 mm) a b do not put furniture or objects within 36” (914 mm) of the front of appliance combustible mantel clearances *measure taken from the underside of the mantel to fi nished hearth or surface that the unit is sitting on. Finishing materials combustible materials: material such as wood, co...
Approved termination required max. 36” offset at 10’-0” min. Vertical 3” liner 3” min. Bend radius m in. 10 f eet (with off set) m in. 8 f eet (without off set) minimum vent liner radius allowable vent configurations minimum vent lengths. For other allowable configurations, refer to the venting tabl...
Installation planning installer—read this first 1. You need to know from the homeowner what accessories (surround, door, etc.) will be installed with this fi replace; 2. Unpack the appliance. 3. Check that you have everything. 4. Clean cavity, chimney, ash dumps, clean-outs. 5. Install venting pipe....
Unpack the appliance beware of sharp edges! Wear gloves! 1. Unpack the appliance. 2. Unpack any loose items from around the appliance and check against the pack content list provided in the documentation package. 3. Remove the window and set aside in a safe place to avoid damage. 4. Verify that you ...
Connect vent important: this appliance’s venting system requires room air to be used in the combustion process. 1. Rough-in one 3” diameter vent liner into the existing chimney system from the roof. Be careful not to tear or damage the liner in the process. Leave plenty of liner at the bottom to fac...
Supply pressure test tapping manifold pressure test tapping installation connect gas supply the gas supply inlet connection is a 3/8” npt female connector and is located on the left hand side of the control valve. Use only new black iron or steel pipes or copper tubing if acceptable—check local code...
Push-on connector connect remote control receiver 1. Connect the wiring harness to the receiver box, by pushing the wire connector on to the receiver circuit board. The plug will only go on one way so please ensure that the wires are pointing up and the slot in the board is in line with the tab on t...
Rotate anchor up and insert panel position of panel in relation to burner plate edge of burner plate side panels should be parallel to edge of burner plate installation change fuel bed support (if necessary) the appliance is supplied with the log support already installed. If installing the log set ...
Port cover installed installation 4. Rotate the anchor up and out of the way and slide the right hand side panel against the fi rebox side. The panel should be parallel to the edge of the burner plate. Rotate the anchor back down to hold the panel. 5. Tighten the side brick anchors on each side of t...
Pilot area pilot area rear log support rear log outline burner burner top view install 739lsk ceramic logs unpack the ceramic logs very carefully to avoid damaging the fragile material. Install the logs as shown below. Please note that the position of the logs is critical to ensure proper performanc...
Notch in rear log pin in front right log installation 4. Place the front right log on the burner and slide it to the left against the front left log. 5. Locate the top right log on the two pins on the right side of the rear log. Ensure a tight fi t against the fl at area around the pins in the rear ...
To p bottom 1 2 installation fuel bed base installed install 739rsk ceramic rocks the use of the 739rsk ceramic rock set requires a change from the factory-installed log support to the rock support supplied with this kit. See section change fuel bed support on page 23 for instructions on how to chan...
Rock identi fi cation triangular hole in ceramic base all rocks installed glass panel installed 4. The underside of each ceramic rock is identi fi ed by a number and a speci fi c protruding positioning triangle. Install the six rocks from left to right starting with rock no. 1. 5. Place the glass pa...
Install 739dwk driftwood kit the log support is factory-installed in a speci fi c position which can be adjusted if necessary. Moving the support forward will allow more impigement/glow/ fl ame height on the left side of the fi re; moving the support backward will do the opposite. Unpack the driftwo...
4. Identify the right side cross log, the longest, and place it across the rear log. The narrow end of the log rests in a notch of the rear log. The wide end of the log lays fl at on the platform, fl ush with the edge as indicated. 5. Identify the left side cross log which has one pin at one end. In...
Open open close close ng flashback shield (for lpg only) lpg air shutter slider open close lpg ng air shutter slider & cover hot glass warning plate bottom of window (wider frame) re-install and check window 1. To re fi t the window, hook its top part to the fi rebox’s opening frame. Make sure that ...
Packing contents: 1 wall bracket a 2 screws b 1 screw c 2 wall anchor d 1 spacer e (detach before assembly) 1 wall bracket f switch plate alternative 1 alternative 2 alternative 3 install handset wall holder the remote control kit for this fi replace comes complete with a wall-mounted holder. This h...
Warranty warr an ty pr og ram warr an ty pr og ram va lor co m fo r t va lor co m fo r t va lor co m fo r t 1. Extended warranty coverage for a period of up to ten (10) years, miles industries ltd., (the “company”) or its appointed distributor will at its option pay the initial owner for the repair ...
Spare parts code description part number 1 exhaust slide assembly 4000127 2 port cover 4001820ah 3 log support 4004353 4 side bricks anchors (2) 4001283 5 top mounting bracket 4000136az 6 side mounting brackets (2) 4000135az 7 window assembly 4001378 8 burner assembly ng 4001180 burner assembly lpg ...
Spare parts code description part number 65 front support—platform 4001835by 66 ceramic platform 4001832 67 rock support 4001768 68 driftwood kit 739dwk 69 rear log 4005615 70 base log 4005617 71 rh cross log 4005616 72 front log 4005819 73 lh cross log 4005618 74 small beige beach pebble (3) 400308...
Spare parts ng lpg 55 56 57 58 59 60 61 54 62 63 67 64 65 66 1 2 3 4 5 6 7 9 10 11 12 13 14 15 16 24 27 26 25 30 28 29 49 50 51 52 48 41 42 43 44 45 46 47 12a ng lpg 11a 32 35a, 35b 36 37 38 39 40 53 18 23 19 20 21 22 17 31 36 owner’s information.
Thank you ... For purchasing a valor by miles industries. Your new radiant gas heater is a technical appliance that must be installed by a quali fi ed installer. Please fi ll in the information below. The information provided will be used for customer records only. Online warranty registration at ww...
Tape shut thank you for choosing a valor product postage needed miles industries ltd. 190 - 2255 dollarton highway north vancouver, bc v7h 3b1 canada fold here online warranty registration at www.Valor fi replaces.Com.
