1. DL manuals
  2. Valor
  3. Indoor Fireplace
  4. Retrofire F24BN
  5. Installation And Owner's Manual

Valor Retrofire F24BN Installation And Owner's Manual

Manual is about: Gravity Vent Fireplace insert

Summary of Retrofire F24BN

  • Page 1

    4001003-12 © 2010 miles industries ltd. All rights reserved patents pending model rf24bn/bp gravity vent fireplace insert installation and owner’s manual warning: if the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury...

  • Page 2: Do Not Put

    2 we recommend that our gas hearth products be installed and serviced by professionals who are certified in the united states by nfi (national fireplace institute ® ). Thank you ... For purchasing a valor retrofire. Your new radiant gas heater is a technical appliance that must be installed by a qua...

  • Page 3

    3 safety and warning information.......................................................... 4 specifications .......................................................................................5 dimensions and clearances ................................................................6 venting ......

  • Page 4

    4 safety and warning information children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid burns or clothing ignition. Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young children and othe...

  • Page 5

    5 safety and warning information specifications this appliance as supplied is intended for installation into existing masonry or factory built solid-fuel burning fireplaces only, unless the separately supplied zero clearance kit ra24zc is used. See separate instructions packaged with the zero cleara...

  • Page 6

    6 dimensions— for solid-fuel burning fireplace insert only see separate framing dimensions for zero clearance applications with the zero clearance kit ra24zc. Minimum cavity dimensions —for solid-fuel burning fireplace insert (see separate framing dimensions for zero clearance applications in the ze...

  • Page 7

    7 vent materials use a 3” diameter aluminium flex liner approved for gas venting when installing as an insert (existing chimneys). Use a 4” diameter type “b” vent when installing with a ra24zc zero clearance kit. See separate instructions packaged with the zero clearance kit. The minimum vent length...

  • Page 8

    8 existing fireplace preparation a few points must be considered before inserting the rf24 into an existing fireplace cavity. Generally, modifications to the existing fireplace that will compromise its integrity are not allowed. Components that are bolted or screwed on, such as dampers or baffles, m...

  • Page 9

    9 supply gas • it is preferable to rough-in the gas line at this point before proceeding with the firebox installation. • the gas supply inlet connection is a 3/8” npt female connector. For detailed location of this connector, see illustration in section dimensions. If a circulating fan or isolating...

  • Page 10

    10 3” dia. Aluminum liner rough-in the 3” diameter vent liner into existing chimney system being careful not to tear or damage the liner in the process. Leave plenty of liner at the bottom end if the heater will be connected while on the hearth—see diagram in connect liner to the firebox section. Wh...

  • Page 11

    11 connect liner to the firebox the vent plate will ultimately locate approximately 19” above the base of the fireplace once inserted. 1. Trim the liner accordingly so it will not be too long once the firebox in raised. 2. Connect the liner to the vent plate using the gear clamp provided. 3. Stretch...

  • Page 12

    12 reinstall the burner module note: if the circulating fan is to be installed, it should be done at this point before installing the burner module. See instructions packaged with the fan for installation details. Reinstall the burner module using the 4 screws removed previously. Note: the upper baf...

  • Page 13

    13 install the ceramic brick liner install the ceramic brick liner taking care not to damage them as the material is fragile. The top rounded edges of the side panels should face inwards and the front edge is bevelled. Place the side brick panels flat up high against the side of the firebox and slid...

  • Page 14

    14 place r/h cross log onto locating pins l/h log locating pins place middle cross log across gap in front log place l/h cross log onto locating pins install the ceramic log set hook the window over the top edge of the firebox and fasten the bottom two spring-loaded bolts by pushing in and turning 9...

  • Page 15

    15 air shutter in open position air shutter in closed position air shutter air shutter retainer air shutter components remote control installation operation check and aeration adjustment 1. Connect the wiring harness to the receiver box, by pushing the wire connector on to the receiver circuit board...

  • Page 16

    16 install the fret retainer brackets 1. Release the two thumbscrews on the each side of the fireplace. 2. Fit the slotted holes in the fret retainers over the thumbscrews and push the retainers down. 3. Tighten the thumbscrews. Install the cast iron fret 1. Adjust the screw heads on the back of the...

  • Page 17

    17 owner’s information spring-loaded fastening studs (2) 1/4 turn please read the safety and warning information section at the beginning of this manual. Operating your fire for your safety, this appliance is fitted with a flame supervision device which will shut-off the gas supply if, for any reaso...

  • Page 18

    18 owner’s information batteries replacement all appliances use four 1.5 v aa alkaline batteries for remote control receivers and the handset uses a 9 v alkaline battery. Batteries are accessible by removing the lid of the remote control receiver. Batteries should last one to two seasons, depending ...

  • Page 19

    19 remote control operation caution do not use a screwdriver or other metallic object to remove the batteries from the receiver or the handset! This could cause a short circuit to the receiver. Setting the temperature use this setting when you come in and want to enjoy a specific temperature. 1. Pus...

  • Page 20

    20 options fuel rf24bn—natural gas installations rf24bp—propane gas installations accessories (sold separately) decorative cast iron frets ra24cv—contemporary, vintage iron finish ra24av—avant-garde, vintage iron finish ra24tb—traditional, black finish 1225vfb—ventana fret, black finish venting pipe...

  • Page 21: Lighting Instructions

    21 lighting instructions for your safety read before lighting warning: if you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot, which must be lighted by hand. When lighting the pilot, foll...

  • Page 22: Lor

    22 warranty 1. Extended warranty coverage for a period of up to ten (10) years, miles industries ltd., (the “company”) or its appointed distributor will at its option pay the initial purchaser for the repair of, or will exchange the following parts or components which are found to be defective in ma...

  • Page 23

    23 parts key description part number 1 firebox assembly 4000634ah 2 vent plate 4001010 3 convection baffle 4001009 4 lh fret support 4000693 5 wing nuts (2) 4000741 6 lh leg 4000662 7 screw m5 x 50mm, hex hd (2) 4000242 8 log support 4000621 9 rh leg 4000663 10 rh fret support 4000694 11 thumbscrew ...

  • Page 24

    24 parts.

  • Page 25

    Thank you ... For purchasing a valor by miles industries. Your new radiant gas heater is a technical appliance that must be installed by a qualified dealer. Please circle where appropriate - ask your installer if in doubt:information provided will be used for customer records only. Online warranty r...

  • Page 26

    Tape shut thank you for choosing a valor product postage needed were you given all documentation and manuals for your product? Yes no miles industries ltd. 190 - 2255 dollarton highway north vancouver, bc v7h 3b1 canada fold here online warranty registration at www.Valorfireplaces.Com.