1. DL manuals
  2. Valore
  3. Ventilation Hood
  4. VLA-E30AS
  5. Use, Care And Installation Manual

Valore VLA-E30AS Use, Care And Installation Manual

Manual is about: Lateral Wall

Summary of VLA-E30AS

  • Page 1

    Use, care, and installation guide model number: serial number: lateral wall vla-e30as vla-e36as jun11.0101.

  • Page 3: Able of Contents

    1 safety notice ................................................................. 2-3 list of materials ....................................................... 4 installation ducting calculation sheet ....................................... 5 mounting height & clearance ................................

  • Page 4: Important Safety Notice

    Important safety notice read and save these instructions 2 warning to reduce the risk of fire or electric shock, do not use this fan with any solid-state control device. Warning to reduce the risk of fire electric shock, or injury to persons, observe the following: a. Use this unit only in the manne...

  • Page 5: Important Safety Notice

    Important safety notice 3 warning to reduce the risk of fire, use only metal ductwork. Caution to reduce risk of fi re and to properly exhaust air outside - do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces or garages. Not for use over an outdoor grill. Operation alway...

  • Page 6: List of Materials

    List of materials 4 (3) wire nuts (3) m6 x 1-1/2” (2) m6 x 1” (2) m3.5 x 8 parts not supplied - ducting, conduit and all installation tools - cable connector (if required by local codes) - extension duct cover accessory - v1c-00la - recirculating kit accessory - vrc-00la hardware package contents (1...

  • Page 7: Installation –

    5 duct pieces total equivalent number length x used = 3- 1/ 4” x 10” rect., straight 1 ft. X ( ) = ft. 8” round, straight 1 ft. X ( ) = ft. 3- 1/ 4” x 10” rect. 90 0 elbow 15 ft. X ( ) = ft. 3- 1/ 4” x 10” rect. 45 0 elbow 9 ft. X ( ) = ft. 3- 1/ 4” x 10” rect. 90 0 flat elbow 24 ft. X ( ) = ft. 3- ...

  • Page 8: Installation –

    Installation – mounting height & clearance 6 ducting a minimum of 6” round duct must be used to maintain maximum air fl ow effi ciency. Always use rigid type metal ducts only. Flexible ducts could restrict air fl ow by up to 50%. Use calculation worksheet to compute total duct work (page 5). Always,...

  • Page 9: Installation –

    7 warning fire hazard never exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside, unless using the recirculating option. Use single wall rigid metal ductwork only. Fasten all connections with sheet metal scr...

  • Page 10: Installation –

    8 installation – hood specifi cation 6 " cl 29 15/16” , 35 7/16 ” 14 1/8 ” 2 13/16 ” 20 1/16 ” standard min. Ducted - 26” min. Recirc. - 31” max. - 53” v1c-00la extension min. Ducted - 42” min. Recirc. - 46” max. - 80” 11” 7 1/16 ” 9 7/16 ” 10 9/16 ” 2 3/16 ” 3 9/16 ” 5” top side front.

  • Page 11: Installation –

    9 1. Measure from range top to desired hood bottom location and mark line a. (26” minimum from range top) . 2. Plum and mark center line. 3. Mark hood height line b. (11-1/16” from line a) 4. Mark mounting spread from c/l. (12-5/8” on line b) 5. Fasten (2) m6 x 1-1/2” screws into studs on line b but...

  • Page 12: Installation –

    10 ductless recirculation is intended for applications where an exhaust duct work is not possible to be installed. When converted, the hood functions as a recirculating hood rather than an exhaust hood. Fumes and exhaust from cooking are drawn and fi ltered by a set of optional charcoal fi lters. Th...

  • Page 13: Features & Controls -

    11 blower speed selection press to cycle through blowers speeds i, ii and iii blower on/off 1 lights bright/dim/off 3 3 lights bright/dim/off blower speed selection 2 delay off timer 4 blower on/off press to turn blower on and off. If lights are on they will also switch off when this button is press...

  • Page 14: Maintenance –

    12 surface maintenance: clean the hood surface periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent, or steel wool/scouring pads which will scratch and damage surface. For heavier soil use liquid degreaser. After cleaning it is recommended that you use...

  • Page 15: Maintenance –

    13 replacing light bulbs caution: light bulb becomes extremely hot when turned on. Do not touch bulb until switched off and cooled. Touching hot bulbs could cause serious burns. Make sure all power is turned off and bulbs are not hot. Remove by turning bulb counter clockwise. Note: bulb does not uns...

  • Page 16: Roubleshooting

    14 t roubleshooting troubleshooting procedures for vla issue cause what to do after installation, the unit doesn’t work. 1. The power source is not turned on. 1. Make sure the circuit breaker and the unit’s power is on. 2. The power line and the cable locking connector is not connecting properly. 2....

  • Page 17: Iring Diagrams

    15 w iring diagrams.

  • Page 18: List of Materials

    List of materials 16 description part# replacement parts light bulb gu-10 50w (each) z0b-0020 optional accessories recirculating kit vrc-00la replacement charcoal filters (qty 2) v0f-c002 extension duct cover v1c-00la order replacement parts from us by calling 1.888.750.1698 accessories can be order...

  • Page 19: Limited Warranty

    1-888-750-1698 staple your receipt here to obtain service under warranty or for any service related questions, please call: valore (referred to herein as “we” or “us”) warrants to the original consumer purchaser (referred to herein as “you” or “your”) of valore products (the “products”) that such pr...