1. DL manuals
  2. Valore
  3. Ventilation Hood
  4. VLT-E36AS
  5. Use, Care And Installation Manual

Valore VLT-E36AS Use, Care And Installation Manual

Summary of VLT-E36AS

  • Page 1

    Use, care, and installation guide model number: serial number: lateral island vlt-e36as vlt-e42as jun11.0101.

  • Page 3: Able of Contents

    1 safety notice ................................................................. 2-3 list of materials ....................................................... 4 installation ducting calculation sheet ....................................... 5 mounting height & clearance ................................

  • Page 4: Important Safety Notice

    Important safety notice read and save these instructions 2 warning to reduce the risk of fire or electric shock, do not use this fan with any solid-state control device. Warning to reduce the risk of fire electric shock, or injury to persons, observe the following: a. Use this unit only in the manne...

  • Page 5: Important Safety Notice

    Important safety notice 3 warning to reduce the risk of fire, use only metal ductwork. Caution to reduce risk of fi re and to properly exhaust air outside - do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces or garages. Not for use over an outdoor grill. Operation alway...

  • Page 6: List of Materials

    List of materials 4 (3) wire nuts (1) suction cup (4) ø12 od / ø5 id washers (4) m6 x 1-1/2” wood srews (2) 3/16 x 1/4” machine screws (12) m3 x 5 machine screws (8) m4 x 8 machine screws (1) hardware package (1) 6” round damper (pre-installed) (4) 3/16 *1/2” mounting screws (pre-installed) (1 in ea...

  • Page 7: Installation –

    5 duct pieces total equivalent number length x used = 3- 1/ 4” x 10” rect., straight 1 ft. X ( ) = ft. 8” round, straight 1 ft. X ( ) = ft. 3- 1/ 4” x 10” rect. 90 0 elbow 15 ft. X ( ) = ft. 3- 1/ 4” x 10” rect. 45 0 elbow 9 ft. X ( ) = ft. 3- 1/ 4” x 10” rect. 90 0 flat elbow 24 ft. X ( ) = ft. 3- ...

  • Page 8: Installation –

    Installation – mounting height & clearance 6 ducting a minimum of 6” round duct must be used to maintain maximum air fl ow effi ciency. Always use rigid type metal ducts only. Flexible ducts could restrict air fl ow by up to 50%. Use calculation worksheet to compute total duct work (page 5). Always,...

  • Page 9: Installation –

    7 and installer. Warning fire hazard never exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside, unless using the recirculating option. Use single wall rigid metal ductwork only. Fasten all connections with ...

  • Page 10: Installation –

    8 installation – hood specifi cation cl 35 7/8” , 41 7/8 ” 14” 3 15/16 ” 26 7/8 ” standard min. Ducted - 28” min. Recirc. - 30” max. - 41” v1c-00lt extension min. Ducted - 50 1/2” min. Recirc. - 54 1/2” max. - 79” 12” 4 5/8 " 2 3/16 " 6” top 12 3/8 " 9 1/2 ” 12 3/16 ” 7 1/16 ” front side.

  • Page 11: Installation –

    9 1 2 ceiling joists wood blocking top support frame support frame arm bottom support frame hood body blower housing 3 mounting screws (pre-installed) 4 installation – mounting the hood 1. Determine mounting location on ceiling and temporarily tape paper template (included with the hood) to the ceil...

  • Page 12: Installation –

    10 installation – mounting the hood 1 2 4 3 5 top duct covers top support frame bottom duct covers bottom support frame thin trim piece thick trim piece 5. Install electrical and duct work. A cable lock, not supplied, might be required by local codes. (fig.E) seal duct work with aluminum duct tape. ...

  • Page 13: Installation –

    11 air diverter plate ductless recirculation is intended for applications where an exhaust duct work is not possible to be installed. When converted, the hood functions as a recirculating hood rather than an exhaust hood. Fumes and exhaust from cooking are drawn and fi ltered by a set of optional ch...

  • Page 14: Features & Controls -

    12 blower speed selection press to cycle through blowers speeds i, ii and iii blower on/off 1 lights bright/dim/off 3 3 lights bright/dim/off blower speed selection 2 delay off timer 4 blower on/off press to turn blower on and off. If lights are on they will also switch off when this button is press...

  • Page 15: Maintenance –

    13 surface maintenance: clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent or steel wool/scouring pads which will scratch and damage surface. For heavier soil use liquid degreaser. After cleaning it is recommended that you use non-abrasive stai...

  • Page 16: Maintenance -

    14 replacing light bulbs caution: light bulb becomes extremely hot when turned on. Do not touch bulb until switched off and cooled. Touching hot bulbs could cause serious burns. Make sure all power is turned off and bulbs are not hot. Remove by turning bulb counter clockwise. Note: bulb does not uns...

  • Page 17: Roubleshooting

    15 t roubleshooting troubleshooting procedures for vlt issue cause what to do after installation, the unit doesn’t work. 1. The power source is not turned on. 1. Make sure the circuit breaker and the unit’s power is on. 2. The power line and the cable locking connector is not connecting properly. 2....

  • Page 18: Iring Diagrams

    16 w iring diagrams.

  • Page 19: List of Parts &

    List of parts & accessories 17 description part# replacement parts light bulb gu-10 50w (each) z0b-0020 optional accessories recirculating kit, vlt-e36as vrc-00lt recirculating kit, vlt-e42as vrc-01lt replacement charcoal filters (qty 2) v0f-c002 extension duct cover v1c-00lt order replacement parts...

  • Page 20: Limited Warranty

    1-888-750-1698 staple your receipt here to obtain service under warranty or for any service related questions, please call: valore (referred to herein as “we” or “us”) warrants to the original consumer purchaser (referred to herein as “you” or “your”) of valore products (the “products”) that such pr...