39in epp edge-540 kit instruction manual specifications wingspan : 39.4in (1000mm) length : 40.2 in (1020mm) empty weight: 8.1oz (230g) flying weight : 15.9-17.6oz (450 - 500g).
Www.Valuehobby.Com/39in-edge540-epp.Html 2 dear customer, congratulations on your purchase of elite models edge-54039in epp kit from value hobby. We thank you for your generous support, and hope you enjoy your new airplane. At value hobby, we hope to offer competitive prices, good performance, and p...
Www.Valuehobby.Com/39in-edge540-epp.Html 3 safety in flying this is not a toy! It is a very high-performance rc airplane capable of high speeds and extreme maneuvers. It should only be operated by a competent pilot in a safe area with proper supervision. Only fly your aircraft in a safe, open area, ...
Www.Valuehobby.Com/39in-edge540-epp.Html 4 main parts: 1. Vertical fuselage x 1 2. Horizontal fuselage x 1 3. Wing panel x 2 4. Tail x 1.
Www.Valuehobby.Com/39in-edge540-epp.Html 5 accessories: list: 1. 3mm plywood motor mount x 1 2. Self-tapping socket head screw for motor x 4 m2.5 x 12mm 3. Hook and loop velcro tape x 1 length: 150mm 4. Fiberglass square tube (wing spar) x 1 4 x 4 x 850mm 5. Metal push rod connector x 4 diameter: 1....
Www.Valuehobby.Com/39in-edge540-epp.Html 6 recommended radio equipment product sku quantity radio flysky fs-i6 transmitter and receiver set fly-rc-4572 1 servo towerpro sg90 9g servo twp-sv -0352 4 y-harness universal y-harness 6in (15cm) ams-ac-2397 1 recommended power setup product sku motor gforc...
Step1. Locate the wood pieces for landing gear mount. Step2. Glue the wood pieces together as shown. Step3. Glue the assembled landing gear mount to the vertical fuselage. Step4. Glue two wing panels to the horizontal fuselage. Step5. Glue the wing spar to the slot pre-cut in the wing and fuselage. ...
Www.Valuehobby.Com/39in-edge540-epp.Html 8 step9. Install the extended servo arm using two m2 x 6mm self-tapping screws. Step10. Install a push rod connector to the servo arm. Step11. Install two aileron servos as shown using hot glue. Step12. Install elevator servo and rudder servo onto the fuselag...
Www.Valuehobby.Com/39in-edge540-epp.Html 9 step15. Cut a slot on the aileron for the control horn and install an aileron control horn. Step16. Install the rudder control horn and elevator control horn. (the slots for rudder and elevator control horn are pre-cut.) step17. Install the tail skid (92mm ...
Www.Valuehobby.Com/39in-edge540-epp.Html 10 step20. Cut the 160mm steel wire with z-bend to 2 wires. Step21. Attach the z-bend wire to the control horn, and one short wire to the push rod connector, then tighten the screw on the push rod connector. Step22. Use heat shrinking tube to connect the shor...
Www.Valuehobby.Com/39in-edge540-epp.Html 11 step28. Finish the rudder servo linkage installation. Step29. Prepare a motor with motor mount and prop adapter installed. Install the motor to the motor mount using four m2.5 x 12mm self-tapping screws. Step30. Install the prop to the motor. Step31. Cut t...
2015-10-05.
