Aeromaster-46 almost ‐ ready ‐ to ‐ fly nitro/electric aerobat instruction manual specifications wingspan: 59 in (1470mm) length: 49 in (1250mm) wing area: 604.5 sq in (39sq dm) flying weight: 4.4lb ‐ 4.85lb (2000 ‐ 2200g).
Http://www.Valuehobby.Com/ 2.
Http://www.Valuehobby.Com/ 3 dear customer, congratulations on your purchase of aeromaster ‐ 46 arf from value hobby. We thank you for your generous support, and hope you enjoy your new airplane. At value hobby, we hope to offer competitive prices, good performance, and products that you can setup a...
Http://www.Valuehobby.Com/ 4 only fly your aircraft in a safe, open area, away from spectators and vehicles–and where it is legal to fly. Never fly over an unsafe area, such as a road or street. Never fly too close to yourself or spectators. Never run your motor inside a house or building with the p...
Http://www.Valuehobby.Com/ 5 main parts of the airplane accessories and small parts not pictured configuration model qty radio 4 channel 1 motor size gforce g32 brushless outrunner motor (4250 ‐ 800kv) 1 speed control 80a brushless esc 1 recommended battery （ lipo ） gforce 30c 4000mah 4s14.8v lipo 1...
Http://www.Valuehobby.Com/ 6 section 1: aileron installation. 1. Drill a 1/16 ‐ inch hole into the center of each hinge slot in the aileron and wing panel. Trim the covering away from each hinge slot to ensure that the hinges will be properly glued in place. 2. Test fit a ca hinge into each of the h...
Http://www.Valuehobby.Com/ 7 section 2: aileron servos & pushrods installation. Before installation, confirm that the servos that you will be using will properly fit in the servo opening. Make adjustments as necessary for your brand servos. The servo openings shown in this section will fit standard ...
Http://www.Valuehobby.Com/ 8 5. Place one of the nylon control horn on the aileron, positioning it as shown in the sketch and aligning it with the servo arm using a straight edge as a guide. Mark the location for the screw holes. Using a Ф 1.8mm drill bit, drill a hole through the aileron at the mar...
Http://www.Valuehobby.Com/ 9 section 3: finish the wing panels 1. Use the wing tube to attach the wing halves to the fuselage. 2. Install the wing panels onto the wing tube and secure them to the fuselage using two nylon wing bolts. (test the cm5x20mm wing bolts into the blind nuts in the wing panel...
Http://www.Valuehobby.Com/ 10 3. Insert the vertical fin in the fuselage slot. Adjust it to be symmetric and equidistant from the left to right, perpendicular to the fuselage. 4. Temporarily insert a Ф 1.8x 730mm pushrod into each elevator pushrod exit slot. Use the position of the pushrod to align ...
Http://www.Valuehobby.Com/ 11 section 5: install the tail servos & pushrods 1. With the rudder in the neutral position and the rudder servo arm perpendicular to the pushrod, mark where the. 2. Attach two Ф 1.8x 730mm pushrods with nylon clevises and silicone clevis retainers to the third from outer ...
Http://www.Valuehobby.Com/ 12 3 attach the landing gear legs to the fuselage using two cm4x20mm shcs, two m4 flat washers, two m4 lock washers. Section7: installing a nitro motor 1. The fuel tank can be assembled as a two line system consisting of a vent (pressure) line to the muffler and a carb lin...
Http://www.Valuehobby.Com/ 13 3. Insert the tank into the fuselage with the correct side facing up. The fuel tubing should be routed through the hole in the center of the firewall. 4. Using four pm4x20mm shcs, four m4 fiat washers, four m4 lock washers, and thread locking compound, attach the engine...
Http://www.Valuehobby.Com/ 14 section 9: install the cowl 1. Drill 1/16" [1.6mm] holes at the marks you made on the cowl through the cowl mounting blocks. Remove the cowl and thread a pwa3x12mm self ‐ tapping screw into each hole in the cowl mounting blocks and back it out. Apply a couple drops of t...
Http://www.Valuehobby.Com/ 15 section 10: setting cg and control throws recommended cg for the first flights, the recommended center of gravity location is 124mm behind the leading edge of the wing against the fuselage. Use the battery pack, moving it forward or backward, to achieve the correct bala...
Http://www.Valuehobby.Com/ 16 finally... Enjoy your aeromaster-46 have a nice flight!.
