1. DL manuals
  2. Value Hobby
  3. Toy
  4. Aviator Trainer25 ARF
  5. Instruction Manual

Value Hobby Aviator Trainer25 ARF Instruction Manual

Summary of Aviator Trainer25 ARF

  • Page 1

    Aviator trainer25 arf instruction manual specifications wingspan: 54.3in (1380mm) length: 45.2in (1150mm) wing area: 438sq in (34sq dm) flying weight: 3.8lbs (1700g).

  • Page 2

    Www.Valuehobby.Com/aviator-trainer-25-arf.Html 2 dear customer, congratulations on your purchase of aviator trainer 25 arf from value hobby. We thank you for your generous support, and hope you enjoy your new airplane. At value hobby, we hope to offer competitive prices, good performance, and produc...

  • Page 3

    Www.Valuehobby.Com/aviator-trainer-25-arf.Html 3 safety in flying this is not a toy! It is a very high-performance rc airplane capable of high speeds and extreme maneuvers. It should only be operated by a competent pilot in a safe area with proper supervision. Only fly your aircraft in a safe, open ...

  • Page 4

    Www.Valuehobby.Com/aviator-trainer-25-arf.Html 4 recommended radio equipment product sku quantity radio flysky t6 6ch radio fly-rc-2563 1 servo towerpro sg5010 standard servo twp-sv-0368 4 electric 5 nitro y-harness universal servo y-harness 12-inch (futaba "j" and jr compatible) ams-ac-0869 1 exten...

  • Page 5

    Www.Valuehobby.Com/aviator-trainer-25-arf.Html 5 main parts: accessories:.

  • Page 6

    Www.Valuehobby.Com/aviator-trainer-25-arf.Html 6 pack 1: steering arm x 1 pu wheel x 3 Φ55*24mm (1.0inch) wheel collar x 7 landing gear strap x 2 self-tapping screws for landing gear strap x 4 m3*12mm (0.5inch) pack2: 180cc fuel tank x 1 pack3: electric motor mount x 1 socket head screw m3*15mm (0.6...

  • Page 7

    Section1. Aileron installation step1. Place t-pin or something similar to this in the center of each hinge. Step2. Insert the hinges into the slots pre-cut in the aileron. Step3. Use the hinges to place the aileron in position. Use a hobby knife to set a gap between the aileron and the wing. Also ch...

  • Page 8

    Www.Valuehobby.Com/aviator-trainer-25-arf.Html 8 section2. Aileron servo & linkage installation step1. Locate the items shown in picture. (servos sold separately.) step2. Use a hobby knife to remove the coverings for the inboard servo and servo lead. Step3. Thread the servo arm through the wing out ...

  • Page 9

    Www.Valuehobby.Com/aviator-trainer-25-arf.Html 9 step8. Thread a clevis to the aileron servo pushrod ( Φ1.8x150mm (6.0inch)), and connect the clevis to the control horn. Step9. With the pushrod wire is 90-degrees to the hinge line and holes in the control horn aligned with the hinge line, use a dril...

  • Page 10

    Www.Valuehobby.Com/aviator-trainer-25-arf.Html 10 step3. Locate the items shown in the picture. Step4. Use the hobby knife to remove the coverings to expose the holes on the wing and wing bolt plate. Step5. Install the wing to the fuselage using two m3*30mm (1.2inch) screws and two m3 washers. Secti...

  • Page 11

    Www.Valuehobby.Com/aviator-trainer-25-arf.Html 11 step4. Use a felt-tipped pen to trace the outline of the fin on the stabilizer and fuselage. Step5. Use a hobby knife to remove the coverings from fuselage and stabilizer inside the line drawn. Step6. Use the epoxy to glue the fin and stabilizer to t...

  • Page 12

    Www.Valuehobby.Com/aviator-trainer-25-arf.Html 12 section5. Rudder elevator servo & linkage installation we recommend you to install the rudder servo on the left tray, elevator servo on the right tray. Step1. Slide the Φ1.8x600mm (23.6inch) elevator servo pushrod to the guiding tube. The threaded en...

  • Page 13

    Www.Valuehobby.Com/aviator-trainer-25-arf.Html 13 step5. Locate the items for nose wheel installation. Step6. Assemble the nose wheel as shown. The nose wheel mount is installed in factory. Step7. Locate the electric motor and install it to the fuselage. Step8. Connect the pushrod for nose wheel to ...

  • Page 14

    Www.Valuehobby.Com/aviator-trainer-25-arf.Html 14 step10. Install two servos to the fuselage. With rudder elevator and steering arm centered, tighten the screw to secure the pushrods to the arm. Step11. Install the electric motor to the mount. Section6. Nitro engine installation step1. Position the ...

  • Page 15

    Www.Valuehobby.Com/aviator-trainer-25-arf.Html 15 step4. Install the throttle servo. Move the servo the throttle open position using the radio system. Manually move the throttle arm on the carburetor to the open position. Secure the pushrod wire to the servo arm. Step5. The fuel tank can be assemble...

  • Page 16

    Www.Valuehobby.Com/aviator-trainer-25-arf.Html 16 section7. Landing gear installation step1. Locate the items for installing main landing gear step2. Use two wheel collars to secure the wheel to the landing gear strut. Step3. Repeat steps 2 through 3 to install the other wheel. Step4. Use a hobby kn...

  • Page 17

    Www.Valuehobby.Com/aviator-trainer-25-arf.Html 17 section8. Set cg and control throws for the first flight, the recommended cg is 83.4mm (3.3inch) behind the leading edge of the wing against the fuselage. Use the battery pack, moving it forward or backward to achieve the correct balance. Control thr...

  • Page 18

    Www.Valuehobby.Com 2013-4-9.