Easy stik 15 epp arf instruction manual specifications wingspan: 41.0 in (1040 mm) length: 35.8 in (910 mm) wing area: 315 sq in (20.3 sq dm) flying weight: 1.4 lbs (650 g).
Www.Valuehobby.Com/easystik15-epp.Html 2 dear customer, congratulations on your purchase of easy stik 15 epp arf from value hobby. We thank you for your generous support, and hope you enjoy your new airplane. At value hobby, we hope to offer competitive prices, good performance, and products that yo...
Www.Valuehobby.Com/easystik15-epp.Html 3 safety in flying this is not a toy! It is a very high-performance rc airplane capable of high speeds and extreme maneuvers. It should only be operated by a competent pilot in a safe area with proper supervision. Only fly your aircraft in a safe, open area, aw...
Www.Valuehobby.Com/easystik15-epp.Html 4 recommended radio equipment product sku quantity radio flysky t6 6ch transmitter and receiver set fly-rc-2563 1 servo towpro mg90 metal gear micro servo twp-sv-0359 4 servo extension universal servo extension 12-inch ams-ac-0560 2 y-harness universal servo y-...
Www.Valuehobby.Com/easystik15-epp.Html 5 main parts and accessories:.
Www.Valuehobby.Com/easystik15-epp.Html 6 list: 1. M3*15 (0.6 in) socket head screw for mounting motor 4pcs 2. M3 blind nut 3pcs 3. 150mm (5.9in) hook and loop tape 4. Main landing gear 5. Plywood spacer for securing the landing gear 6. Wheel collar 2pcs 7. Wheel x 2 8. Wing tube (1000mm fiberglass r...
Www.Valuehobby.Com/easystik15-epp.Html 7 section1. Servo and wing installation step1. Use a hobby knife to cut a notch on the wing for burying the aileron servo lead. Step2. Press the wire lead into the slot. Step3. Use hot glue to glue the servo into the wing. Step4. Insert two wing tubes into the ...
Www.Valuehobby.Com/easystik15-epp.Html 8 step7. Cut off the excess wing tube protruding from the wing. Section2. Aileron servo linkage installation step1. Use a drill bit to enlarge the hole in the control horn. Step2. Install a pushrod connector to the servo arm. Step3. Install the servo arm to the...
Www.Valuehobby.Com/easystik15-epp.Html 9 section3. Horizontal tail and vertical tail installation step1. Use a ruler to make the center line in the horizontal tail. Step2. Lay the plane upside down and place the fuselage in position. Don’t push the stabilizer against the fuselage to make sure the el...
Www.Valuehobby.Com/easystik15-epp.Html 10 step.3 install the servo arm to the rudder servo. Install the z bend to the control horn and slide the pushrod wire through the pushrod connector. Position the control horn on the rudder to make the pushrod wire is 90 degree aligned with the servo arm and th...
Www.Valuehobby.Com/easystik15-epp.Html 11 section5. Landing gear installation step1. Slide one wheel collar onto the wheel axle, then the wheel and then the remaining wheel collar. Tighten the set screws to hold the wheel on the center of the axle. Step2. Insert the landing gear into the slots. Step...
Www.Valuehobby.Com/easystik15-epp.Html 12 section6. Installing the wing to fuselage step1. Glue the two carbon fiber strips to the wing as shown. Step2. Slide the 100mm carbon fiber rod into the pre-drilled hole in the front of the fuselage. Center the rod so it extends equally from the both sides o...
Www.Valuehobby.Com/easystik15-epp.Html 13 section7. Motor installation step1. Install the motor onto firewall using four blind nuts and four m3*15mm socket head screws. Section8. Cg and control throws the recommended cg is 56mm (2.2in) from the leading edge of the wing. Control throws aileron 25 deg...
Www.Valuehobby.Com 2013-8-19.
